Subscribe to Our Youtube Channel
Related Manuals for Clarke LOGBUSTER 9
Summary of Contents for Clarke LOGBUSTER 9
- Page 1 8 TONNE LOG SPLITTER MODEL NO: LOGBUSTER 9 PART NO: 3402043 OPERATION & MAINTENANCE INSTRUCTIONS LS0318 ISS 4...
-
Page 2: Specifications
INTRODUCTION Thank you for purchasing this CLARKE 8 Tonne Log Splitter. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. -
Page 3: Safety Symbols
SAFETY SYMBOLS Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 4: General Safety Rules
GENERAL SAFETY RULES WARNING: READ ALL INSTRUCTIONS. FAILURE TO FOLLOW ALL INSTRUCTIONS LISTED BELOW MAY RESULT IN SERIOUS INJURY. WARNING: SAVE THESE INSTRUCTIONS. WORK AREA 1. Keep the work area clean and well lit. Cluttered and dark areas invite accidents. 2. -
Page 5: Additional Precautions For Log Splitters
SERVICE 1. Have your log splitter serviced by a qualified repair person using only identical replacement parts. This will ensure that safety is maintained. ADDITIONAL PRECAUTIONS FOR LOG SPLITTERS • All personnel must read the manual or receive correct training before they use the log splitter. -
Page 6: Attach The Handles
ASSEMBLY ATTACH THE HANDLES 1. Attach a handle to each side of the log splitter. 2. Use the lock washer and hex nut to lock the handgrip in position. ATTACH THE HYDRAULIC PUMP 1. Use the two inner hex screws supplied to attach the hydraulic pump to the base. -
Page 7: Attach The Base Feet
ATTACH THE BASE FEET 1. Carefully lay the Log Splitter on it’s back. 2. Attach the stabilisers to each side of the bottom of the log splitter. 3. Use two hex bolts two Lock Washers and two hex nuts. to secure each stabiliser. 4. -
Page 8: Attach The Log Cradle
ATTACH THE LOG CRADLE 1. Attach the log cradle to the main post by using hex bolts and lock washers. PREPARATION PREPARING THE LOGS 1. Cut the logs to a suitable length to fit into the log splitter. 2. Put the log on the table. 3. -
Page 9: Adjust The Wedge Height
ADJUST THE WEDGE HEIGHT 1. With the log is placed securely on the table, pull and hold the two wedge release pins and lower the wedge to a little higher than the top of the log. 2. Release the pins, making sure they both engage into the nearest post holes. -
Page 10: Operating The Log Buster
OPERATING THE LOG BUSTER This Logbuster is designed to be operated by one person only. • Do not try to split a log that is larger than those shown in the picture. 230 mm • Do not put your hands anywhere near the splitting wedge during use. -
Page 11: Maintenance
3. Lay the pump horizontal and remove the oil plug from the rear of the pump. 4. Add hydraulic oil until the cylinder is approximately 3/4 full. IMPORTANT: Only use CLARKE HYDRAULIC OIL, available from your nearest dealer. Part No: 1Ltr -3050830 5Ltr -3050835 5. -
Page 12: Troubleshooting
Refer to “Operating the Log Buster” on page 10. Wedge cutting edge is blunt. Refer to “Sharpening The Wedge” on page 11. Oil leaks. Contact the Clarke service department. Unauthorised adjustment was Contact the Clarke service made to the Maximum department. -
Page 13: Exploded Diagram - Parts List
EXPLODED DIAGRAM - PARTS LIST Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... - Page 14 EXPLODED DIAGRAM - PARTS LIST DESCRIPTION PART NO Sleeve with Thread SCLOGB901 SCLOGB902 Ring SCLOGB903 Pressure Spring SCLOGB904 Foot Pedal SCLOGB905 Hex Bolt SCLOGB906 Main Post SCLOGB907 Handle SCLOGB908 Inner Hex Screw SCLOGB909 Wedge Assembly SCLOGB910 Table SCLOGB911 Hydraulic Pump SCLOGB912 Tension Spring SCLOGB913...
-
Page 15: Declaration Of Conformity
DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
Need help?
Do you have a question about the LOGBUSTER 9 and is the answer not in the manual?
Questions and answers