Replacement Parts; Specifications - Omron H5CR series Manual

H5CR

REPLACEMENT PARTS

Description
Panel mounting bracket (one supplied with H5CR-B and H5CR-S models)
RANGE AND OPERATION MODE SELECTION
Range selection Time unit
- . - - - s 0.001 second
- - . - - s 0.01 second
- - - . - s 0.1 second
- - - - s 1 second
- - min - - s 1 second
- - - . - min 0.1 minute
- - - - min 1 minute
- - hr - - min 1 minute
- - - . - hr 0.1 hour
- - - - hr 1 hour

Specifications

Part number
Classification
Supply
AC
voltage
DC
Operating voltage
Power AC
consumption
DC
Inputs Types available
Signal, Type
reset ON impedance
and gate Residual voltage
OFF impedance
Pulse width
Key Type
protect ON impedance
Residual voltage
OFF impedance
Response time
Control
Type Time limit
output
Instantaneous
Relay Max. load
Min. load
Solid- Max. load
state Residual voltage
Repeat accuracy Power start
Signal start
Setting error
Resetting system
Resetting time Power reset
Indicators
2
Maximum setting
9.999 seconds
99.99 seconds
999.9 seconds
9999 seconds
99 minutes 59 seconds
999.9 minutes
9999 minutes
99 hours 59 minutes
999.9 hours
9999 hours
H5CR-L
Economy type
100 to 240 VAC, 50/60 Hz,
24 VAC, 50/60 Hz
12 to 24 VDC, 20% max.
permissible ripple
85% to 110% of rated voltage
3 VA at 60 Hz, 240 VAC
1 W at 24 VDC
Reset and start signal
No-voltage input
1 kΩ max. (Approx. 2 mA when 0Ω)
2 V max. in ON state
100 kΩ minimum
1 ms or 20 ms selectable for reset and signal
20 ms for gate
No-voltage input
100 kΩ max. (Approx. 2 mA when 0Ω)
1 V max. in ON state
100 kΩ minimum
1 second
SPDT relay output or NPN open collector transistor output (H5CR- S)
—
5 A, 250 VAC resistive load (p.f. = 1)
10 mA, 5 VDC
100 mA, 30 VDC
2 V max., 1 V typical
±0.01%, ±0.05 second max.
±0.005%, ±0.03 second max. (rate for set value)
—
Power reset (A, A-1, A-2, B, D and E modes)
External, manual, automatic resets (may be internal depending on A-1, B, B-1, D and E
operation modes)
0.5 second minimum (A, A-1, A-2, B, D and E modes)
4-digit LCD alphanumeric
display without backlighting
8 mm (0.32 in) H present
value, 4 mm (0.16 in) H
set value
Mode Operation
A ON-delay
A-1 Sustained start signal ON-delay one-shot*
A-2 Power ON-delay
A-3 Power ON-delay/non-power
resettable
B Repeat cycle
B-1 Repeat cycle/non-power
resettable
D OFF-delay
E One-shot
F Cumulative signal ON-delay
*One-shot time, seven choices selectable:
0.1 sec, 0.5 sec, 1 sec, 5 sec, 10 sec, 15 sec, 20 sec
H5CR-B H5CR-S
Standard type Short body type
100 to 240 VAC, 50/60 Hz, —
24 VAC, 50/60 Hz
— 12 to 24 VDC, 20% max.
permissible ripple
—
— 2 W at 24 VDC
Reset, gate, start signal, and key protect
4-digit LCD alphanumeric display with backlighting
8 mm (0.32 in) H present value, 4 mm (0.16 in) H set value
H5CR
Part number
Y92F-30
Output type
Sustained or
Sustained