Advertisement
Quick Links
See also:
Manual
GYROFOCUS:
INSTALLATION AND
USER MANUAL
Keep for future use
2
3
5
11
12
OBLICA
200 Argyle St
Fitzroy VIC 3065
03 9416 0400
Advertisement
Related Manuals for Oblica FOCUS SERIES
Summary of Contents for Oblica FOCUS SERIES
-
Page 1: Table Of Contents
GYROFOCUS: INSTALLATION AND USER MANUAL 1. TECHNICAL DATA 2. PRE-INSTALLATION 3. INSTALLATION 4. OPERATION 5. TESTING Keep for future use OBLICA 200 Argyle St Fitzroy VIC 3065 03 9416 0400... -
Page 2: Technical Data
Flue diameter 219mm Flue weight 16Kg/meter Standard bracket weight 20Kg External flue kit Triple skin 200/250/300mm DETERMINED UNDER TEST CONDITIONS: Nominal thermal output Efficiency 57,8% FLUE ø219 mm FIREBOX ø1250 mm OBLICA | GYROFOCUS INSTALLATION AND USER MANUAL PAGE 2... -
Page 3: Pre-Installation
Congratulations on your purchase of the GyroFocus. This appliance should be installed and checked by a qualified professional. Ensure you have read the operation guidelines thoroughly prior to first use. For any questions or concerns please contact Oblica on 03 9416 0400. The installation process is outlined below: –... - Page 4 IMPORTANT: For information on heat shielding please contact our Frames must also be considered. Timber window office on 03 9416 0400 or email info@oblica.com.au. frames must be treated as combustible surfaces (see 2.3). Aluminium frames can be treated as non-combustible surfaces (see 2.2).
-
Page 5: Installation
200 X 250 X 300 (8’ x 10’ x 12’) RUBBER FLASHING Insulative pad CROSS BAR SET IN-BETWEEN RAFTERS ( Plaster Ceiling Minimum Gap) CEILING FLANGE SUSPENSION BRACKET CONNECTOR LOWER FLUE 219mm dia. OBLICA | GYROFOCUS INSTALLATION AND USER MANUAL PAGE 5... - Page 6 3. INSTALLATION (CONTINUED) PITCHED ROOF INSTALLATION (CUSTOM MADE BRACKET) OBLICA | GYROFOCUS INSTALLATION AND USER MANUAL PAGE 6...
- Page 7 The top of the flue must be 1200mm above the roofline. Alternatively, there must be a minimum distance of 3 meters from any higher section of roof. > 3 m – > 120 cm – > 120 cm > 120 cm – – OBLICA | GYROFOCUS INSTALLATION AND USER MANUAL PAGE 7...
- Page 8 2. Engage the firebox with the bolt bearings as per the diagram below. Black steel single skin lower flue Thrust ball bearings ø21/40 Washers ep. 3mm Bearing holder ø13/27 M12 nuts Safety split pin OBLICA | GYROFOCUS INSTALLATION AND USER MANUAL PAGE 8...
- Page 9 FLOOR PROTECTOR LAID ON JOIST Combustible 300mm Insulative board (20mm) 300mm Combustible Insulative board (20mm) floor (eg. timber) + non combustible finish floor (eg. timber) + non combustible finish Joist Joist OBLICA | GYROFOCUS INSTALLATION AND USER MANUAL PAGE 9...
- Page 10 (eg. timber) (eg.tiles) Concrete TOP VIEW 300mm FIREBOX Floor protector / non combustible finish Combustible floor (eg. timber) 300mm FIREBOX Floor protector / non combustible finish Combustible floor (eg. timber) OBLICA | GYROFOCUS INSTALLATION AND USER MANUAL PAGE 10...
-
Page 11: Operation
• The maximum load capacity for the GyroFocus is 20kg of wood. • Burning only seasoned hardwood helps to protect the environment and lower emissions. For details of a wood supplier in your area please call our office on 03 9416 0400 or email info@oblica.com.au. WARNING: •... -
Page 12: Testing
The maximum carbon dioxide output by the appliance during the high burn rate prescribed in AS/NZS 4013:1999 was 4.54%. CONCLUSION: This appliance meets the requirements of AS/NZS 4013:1999 section 1.2.3 (f) and is classified as an excluded appliance. OBLICA | GYROFOCUS INSTALLATION AND USER MANUAL PAGE 12...