EWM LP-XQ Operating Instructions Manual page 4

Contents
Notes on the use of these operating instructions
5.6.1
5.6.2
5.6.3
5.6.4
5.7 Options (additional components) ................................................................................................. 43
5.7.1
5.7.2
5.7.3
5.8 Access control .............................................................................................................................. 43
5.9 Voltage reducing device ............................................................................................................... 43
5.10 Special parameters (advanced settings) ...................................................................................... 43
5.10.1
5.10.2
5.11 Machine configuration menu ........................................................................................................ 54
5.11.1
5.11.2
5.11.3
6 Rectifying faults.................................................................................................................................... 58
6.1 Display machine control software version .................................................................................... 58
6.2 Error messages (power source) ................................................................................................... 58
6.3 Warnings ...................................................................................................................................... 60
6.4 Resetting JOBs (welding tasks) to the factory settings ................................................................ 61
6.4.1
6.4.2
7 Appendix A ............................................................................................................................................ 62
7.1 JOB-List........................................................................................................................................ 62
4
Welding task selection .................................................................................................. 41
5.6.1.1 Welding current setting .................................................................................. 42
Arcforce......................................................................................................................... 42
Hotstart ......................................................................................................................... 42
Antistick......................................................................................................................... 42
Electronic gas flow control (OW DGC) ......................................................................... 43
Wire reserve sensor (OW WRS) .................................................................................. 43
Wire spool heater (OW WHS) ...................................................................................... 43
Selecting, changing and saving parameters................................................................. 44
5.10.1.1 Ramp time for wire inching (P1) .................................................................... 46
5.10.1.2 Program "0", releasing the program block (P2) ............................................. 47
5.10.1.3 Display mode for Up/Down welding torch with one-digit 7-segment
display (P3) ................................................................................................... 47
5.10.1.4 Program limit (P4) ......................................................................................... 47
5.10.1.5 Special cycle in the operating modes special latched and non-latched
(P5) ................................................................................................................ 47
5.10.1.6 Correction operation, threshold value setting (P7) ........................................ 48
5.10.1.7 Switching programs with the standard torch trigger (P8) .............................. 49
5.10.1.8 Latched/special-latched tap start (P9) ........................................................... 50
5.10.1.9 "Single or dual operation" (P10) setting ........................................................ 50
5.10.1.10 Latched special tapping time setting (P11) ................................................... 50
5.10.1.11 JOB list switching (P12) ................................................................................ 51
5.10.1.12 Lower and upper limits of the remote JOB changeover process (P13,
P14) ............................................................................................................... 51
5.10.1.13 Hold function (P15) ........................................................................................ 51
5.10.1.14 Block JOB mode (P16) .................................................................................. 52
5.10.1.15 Selecting programs with the standard torch trigger (P17) ............................. 52
5.10.1.16 Mean value display for superPuls (P19) ....................................................... 52
5.10.1.17 Predefined execution of the pulsed arc welding process in the PA
program (P20) ............................................................................................... 53
5.10.1.18 Predefined absolute value for relative programs (P21) ................................. 53
5.10.1.19 Electronic gas flow control, type (P22) .......................................................... 53
5.10.1.20 Program settings for relative programs (P23) ............................................... 53
5.10.1.21 Correction or nominal voltage display (P24) ................................................. 53
5.10.1.22 JOB selection in Expert mode (P25) ............................................................. 53
5.10.1.23 Nominal value wire heater (P26) ................................................................... 53
5.10.1.24 Mode switching at welding start (P27) .......................................................... 53
5.10.1.25 Error threshold electronic gas flow control (P28) .......................................... 53
5.10.1.26 Units system (P29) ........................................................................................ 53
5.10.1.27 Selection option - Program sequence with welding power rotary knob
(P30) .............................................................................................................. 53
Reset to factory settings ............................................................................................... 54
Selecting, changing and saving parameters................................................................. 54
Aligning the cable resistance ........................................................................................ 56
Power-saving mode (Standby) ..................................................................................... 57
Resetting a single JOB ................................................................................................. 61
Resetting all JOBs ........................................................................................................ 61
099-00LPXQ-EW501
13.03.2018