Note For Parts List - Denon DN-S3700 Service Manual

NOTE FOR PARTS LIST

1. Parts for which "nsp" is indicated on this table cannot be supplied.
2. When ordering of part, clearly indicate "1" and "I" (i) to avoid mis-supplying.
3. Ordering part without stating its part number can not be supplied.
4. Part indicated with the mark "★" is not illustrated in the exploded view.
5. Not including General-purpose Carbon Film Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.)
6. Not including General-purpose Carbon Chip Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.)
WARNING:
Parts marked with this symbol z have critical characteristics.
Use ONLY replacement parts recommended by the manufacturer.
● Resistors
Ex.:
RN 14K
Type Shape
and per-
formance
RD : Carbon 2B : 1/8 W
RC : Composition 2E : 1/4 W
RS : Metal oxide film 2H : 1/2 W
RW: winding 3A : 1 W
RN : Metal film 3D : 2 W
RK : Metal mixture 3F : 3 W
3H : 5 W
* Resistance
1 8 2 1800ohm=1.8kohm
Indicates number of zeros after effective number.
2-digit effective number.
1 R 2 1.2ohm
1-digit effective number.
2-digit effective number, decimal point indicated by R.
: Units: ohm
● Capacitors
Ex.:
CE 04W
Type Shape Dielectric
and per- strength
formance
CE : Aluminum foil
electrolytic
CA : Aluminium solid
electrolytic
CS : Tantalum electrolytic
CQ : Film
CK : Ceramic
CC : Ceramic
CP : Oil
CM: Mica
CF : Metallized
CH : Metallized
* Capacity (electrolyte only)
2 2 2 2200μF
Indicates number of zeros after effective number.
2-digit effective number.
･ Units:μF.
* Capacity (except electrolyte)
2 2 2 2200pF=0.0022μF
Indicates number of zeros after efective number.
(More than 2)
2-digit effective number.
･ Units:pF
･ When the dielectric strength is indicated in AC,"AC" is included after the dieelectric strength value.
2E 182 G
Power Resist- Allowable Others
ance error
F : ±1%
P : Pulse-resistant type
G : ±2%
NL : Low noise type
: ±5%
J NB : Non-burning type
K : ±10%
FR : Fuse-resistor
M : ±20%
F : Lead wire forming
1H 3R2 M
Capacity Allowable Others
error
F : ±1%
0J : 6.3 V HS : High stability type
G : ±2%
1A : 10 V BP : Non-polar type
: ±5%
1C : 16 V J HR : Ripple-resistant type
K : ±10%
1E : 25 V DL : For change and discharge
M : ±20%
1V : 35 V HF : For assuring high requency
Z : ±80%
1H : 50 V
U : UL part
2A : 100 V
: - 20% C : CSA part
2B : 125 V P : +100%
W : UL-CSA part
C : ±0.25pF
2C : 160 V
F : Lead wire forming
D : ±0.5pF
2D : 200 V
2E : 250 V = : Others
2H : 500 V
2J : 630 V
DN-S3700
FR
BP
2 R 2 2.2μF
1-digit effective number.
2-digit effective number, decimal point indicated by R
･ Units:μF.
2 2 1 220pF
Indicates number of zeros after effective numver.
(0 or 1)
2-digit effective number.
･ Units:pF
57