Related Manuals for Fujitsu MB2140 Series
Summary of Contents for Fujitsu MB2140 Series
- Page 1 FUJITSU SEMICONDUCTOR CM42-00406–1E CONTROLLER MANUAL MC FAMILY MICROCONTROLLER EMULATOR MB2140 SERIES MAIN UNIT (MB2141A) HARDWARE MANUAL...
- Page 2 June 1995 1995 FUJITSU LIMITED All Rights Reserved. Circuit diagrams utilizing Fujitsu products are included as a means of illustrating typical semiconductor applications. Complete information sufficient for construction purposes is not necessarily given. The information contained in this document has been carefully checked and is believed to be reliable.
- Page 3 Preface This manual describes the MB2140 Series Main Unit (MB2141A) which is an application of the F MC Family microcontroller. The main unit operates as an emulator when connected to an emulation pod. This manual is composed of: Chapter 1 Product Handling Describes product and handling Read this chapter thoroughly before using the main unit.
-
Page 4: Table Of Contents
Table of Contents 1. PRODUCT HANDLING ..........1.1 PACKAGE CHECK . - Page 5 Tables Table 1-1 Options ............... . . Table 1-2 Operating and Storage Environments .
- Page 6 Figures Fig. 2.1 System Configuration ............. . Fig.
-
Page 7: Product Handling
1. PRODUCT HANDLING 1.1 PACKAGE CHECK ......1.2 OPTIONS ........1.3 PRECAUTIONS . -
Page 8: Package Check
PRODUCT HANDLING This chapter describes the product and its handling. 1.1 PACKAGE CHECK Check the package for the following parts before using the main unit. Main unit: 1 AC power cable: 1 Pod interface cable A: 1 Pod interface cable B: 1 Pod interface cable C: 1 1.2 OPTIONS The main unit has the options listed in NO TAG. -
Page 9: Precautions
PRODUCT HANDLING 1.3 PRECAUTIONS Take the following precautions when using the main unit. Turn off the power before connecting/disconnecting cables. Hold the case/connector when disconnecting a cable. Never touch any connector pins to avoid a dielectric breakdown. Do not obstruct the ventilation holes. Install and use the main unit according to the User’s Manual . -
Page 10: Product Description
2. PRODUCT DESCRIPTION 2.1 SYSTEM CONFIGURATION ..... . 2.2 APPEARANCE AND NAMES OF COMPONENTS . . . 2.3 SPECIFICATIONS OF MAIN UNIT . -
Page 11: System Configuration
PRODUCT DESCRIPTION 2.1 SYSTEM CONFIGURATION The main unit operates as an emulator when connected to an emulation pod (pod). Remember that the main unit cannot operate by itself. A host computer is connected to the main unit for con- trol. Figure 2.1 shows the hardware system configuration of the main unit. -
Page 12: Appearance And Names Of Components
PRODUCT DESCRIPTION 2.2 APPEARANCE AND NAMES OF COMPONENTS This section describes the names of components. For more information on connections, read Chapter 3. Figures 2.2 and 2.3 show the appearance of the main unit and the names of components, respectively. READY LED POWER LED HARD ERROR LED... -
Page 13: Fig. 2.3 Appearance Of Main Unit (Rear View)
PRODUCT DESCRIPTION Reset switch External TRIG output connec- External EMUL output connec- Power switch RESET TRIG EMUL POWER RS-232C ACIN COM PORT F92100001 RS-232C connector LAN adapter connector AC inlet Fig. 2.3 Appearance of Main Unit (Rear View) Reset switch . -
Page 14: Specifications Of Main Unit
2.3 SPECIFICATIONS OF MAIN UNIT NO TAG lists the specifications of the main unit. Table 2-1 Specifications of Main Unit Item Specifications Name MB2140 series main unit Model MB2141A Power supply 85 to 264 Vac, 3.5 A, 50/60 Hz Operating temperature... -
Page 15: Specifications Of Pod Interface Cable
To connect the main unit and pod, see 3.1. Table 2-2 Components of Pod Interface Cable (per cable) Component name Remarks Connector FCN-237R068-G/E Fujitsu Cover FCN-230C068-D/E Fujitsu Rivet C630-5296-X801 Fujitsu Table 2-3 Specifications of Pod Interface Cable... -
Page 16: Specifications Of Rs-232C Port
PRODUCT DESCRIPTION 2.5 SPECIFICATIONS OF RS-232C PORT The main unit has an RS-232C port. NO TAG lists the specifications of the RS-232C port and Figure 2.5 shows the connector circuit diagram. Table 2-4 Specifications of RS-232C Port Item Specifications Connection type Baud rate 4800, 9600, 19200 [bps] Data bit length... -
Page 17: Connections
3. CONNECTIONS 3.1 CONNECTING EMULATION POD ....3.2 CONNECTION TO HOST COMPUTER ... . -
Page 18: Connecting Emulation Pod
CONNECTIONS This chapter describes connecting the main unit when it is not switched on. For the names of the components, see 2.2. Cautions: Turn off the power when connecting/disconnecting cables; otherwise, the main unit will be damaged. When disconnecting a cable, hold its case or connector; otherwise, the cable may break. -
Page 19: Fig. 3.1 Connection Of Pod Interface Cables
CONNECTIONS READY POWER ERROR Main unit (Note) Pod interface cable B Pod interface cable A Pod interface cable C Note: The D connector is an extension connector used to connect a pod with a D connector. Fig. 3.1 Connection of Pod Interface Cables... -
Page 20: Connection To Host Computer
CONNECTIONS 3.2 CONNECTION TO HOST COMPUTER Connect the main unit to the host computer as shown in Figure 3.2. Main unit RESET TRIG EMUL POWER RS-232C ACIN COM PORT F92100001 RS-232C cable To host machine Fig. 3.2 Connection via RS-232C... -
Page 21: Messages
4. MESSAGES... - Page 22 MESSAGES Three types of front-panel LEDs on the main unit indicate the following. POWER LED (Orange) (Silk-printed POWER): The power is on. READY LED (Green) (Silk-printed READY): <ON> Both the main unit and host computer are ready for communication. <Blinking> The main unit is communicating with the host computer. HARD ERROR LED (Red) (Silk-printed ERROR): A hardware error has occurred.
-
Page 23: Appendix
APPENDIX SPECIFICATIONS OF LAN ADAPTER... - Page 24 APPENDIX SPECIFICATIONS OF LAN ADAPTER The main unit has a LAN adapter option for connection to the communication adapter connector. Appendix Table 1 lists the specifications of the LAN adapter. Appendix Table 1 Specifications of LAN Adapter Item Specifications Communication type TCP/IP LAN connector BNC connector (10BASE2)
-
Page 25: Appendix Figure 1 Connecting Lan Adapter To Main Unit
APPENDIX SPECIFICATIONS OF LAN ADAPTER Connect the LAN adapter to the main unit via the interface cable (LAN adapter accessory) as shown in Appen- dix Figure 1. LAN adapter LAN ADAPTER COM PORT Interface cable RESET TR16 EMUL POWER RS-232C ACIN COM PORT F92100001... -
Page 26: Appendix Figure 2 Connecting Lan Adapter To Network
APPENDIX SPECIFICATIONS OF LAN ADAPTER Connect the LAN connector of the LAN adapter to a network as shown in Appendix Figure 2. Use a light coax- ial cable, a terminator and a Y-type connector which are sold commercially. To network Terminal resistor Light coaxial cable Y-type connector... - Page 27 Index AC power cord, 2-6 IP address, App.-3 Baud rate, 2-8 LAN adapter, 1-3, 2-5, 4-3, App.-3, App.-4, BNC connctor, App.-3 App.-5 Light coaxial cable, App.-5 Communication adapter, 1-3, 2-3, 4-3, App.-3 Parity bit, 2-8 Port address, App.-3 D connector, 2-4, 3-4 Data bit length, 2-8 RS-232C cable, 1-3, 2-3, 3-5, 4-3, App.-3 Emulaton pod, 1-3, 2-3, 3-3, 4-3, App.-3...
- Page 28 FUJITSU MIKROELEKTRONIK GmbH Am Siebenstein 6–10, 63303 Dreieich–Buchschlag, Germany Tel: (06103) 690–0 FAX: (06103) 690–122 Asia Pacific FUJITSU MICROELECTRONICS ASIA PTE LIMITED No. 51 Bras Basah Road, Plaza By The Park, #06–04 to #06–07 Singapore 189554 Tel: 336–1600 FAX: 336–1609...