Sony ICP-X7000 Operation Manual page 24

REMOTE D-sub 9-pin (6), female
Complies with RS-422A standard
Data transfer rate: 38.4 kbps
SERIAL TALLY
D-sub 9-pin (2), female
Complies with RS-422A standard
Data transfer rate: 38.4 kbps
AC input
AC IN A, B 3-pin AC connector (2)
Accessories supplied
75 Ω terminator (1)
T bridge (1)
Operation Manual (1)
Accessories not supplied
AC power cord (for USA and Canada only) (125 V 10 A
2.4 m (8 ft)) (Part No.: 1-551-812-11)
AC power cord (for Europe only) (250 V 10 A 2.5 m (8 ft
3 in)) (Part No.: 1-782-929-13)
MKS-X7700 System Interface Unit
General
Power requirements
100 V to 240 V AC, 50/60 Hz
Current consumption
1.0 A to 0.5 A
Inrush current (1) Maximum possible inrush current at
initial switch-on (Voltage changes
caused by manual switching):
90 A peak, 20 A r.m.s. (240 V AC)
(2) Inrush current after a mains
interruption of five seconds (Voltage
changes caused at zero-crossing):
25 A peak, 10 A r.m.s. (240 V AC)
Operation guaranteed temperature
5 ºC to 40 ºC (41 ºF to 104 ºF)
Performance guaranteed temperature
10 ºC to 35 ºC (50 ºF to 95 ºF)
Storage temperature
–20 ºC to +60 ºC (–4 ºF to +140 ºF)
Dimensions (w/h/d, excluding projections)
440 × 176 × 486 mm
(17
Mass Approx. 15.0 kg (33 lb 1.1 oz)
Reference input
BNC type (2), 75 Ω, with loop-through
REF IN
output
HD tri-level sync/analog black burst/
analog sync
24
Specifications
3 × 7 × 19 1
/ / inches)
8 4
Control connectors
MVS RJ-45
Complies with 1000Base-T
UTIL RJ-45
Complies with 1000Base-T
CAUTION
• For safety, do not connect the connector for peripheral
device wiring that might have excessive voltage to the
following ports.
: MVS connector
: UTIL connector
Follow the instructions in the User's Guide for the above
ports.
• When you connect MVS cable or UTIL cable of the unit
to peripheral device, use a shielded-type cable to prevent
malfunction due to radiation noise.
ATTENTION
Par mesure de sécurité, ne raccordez pas le connecteur
pour le câblage de périphériques pouvant avoir une tension
excessive aux ports suivants.
: MVS connecteur
: UTIL connecteur
Suivez les instructions dans l' User's Guide pour les ports
ci-dessus.
VORSICHT
Aus Sicherheitsgründen nicht mit einem Peripheriegerät-
Anschluss verbinden, der zu starke Spannung für diese
Buchse haben könnte.
: Buchse MVS
: Buchse UTIL
Folgen Sie den Anweisungen in der User's Guide für die
oben aufgeführten Buchsen.
BNC type (1), 75 Ω
S-BUS
Data transfer rate: 312 kbps
TALLY/GPI IN
D-Sub 37-pin (2), female, TTL inputs:
34 × 2
REMOTE D-sub 9-pin (4), female
Complies with RS-422A standard
Data transfer rate: 38.4 kbps
SERIAL TALLY
D-sub 9-pin (2), female
Complies with RS-422A standard
Data transfer rate: 38.4 kbps
AC input
AC IN A, B 3-pin AC connector (2)
Accessories supplied
75 Ω terminator (1)
T bridge (1)
Operation Manual (1)