Siemens 7SV512 Instruction Manual page 60

7SV512
V1
FNo Abbreviation
474 BFP-Start L1
475 BFP-Start L2
476 BFP-Start L3
500 Time del.init
501 BFP CBdefTrip
502 BFP Trip L1
503 BFP Trip L2
504 BFP Trip L3
505 BFP Trip L123
506 BFP CrossTrip
507 BFP Trip BB
508 BFP TransTrip
509 BFP block
510 BFP T1 3pole
511 BFP T1 1pole
512 BFP T2 Curr
513 BFP T2 CBaux
514 BFP Tend Flt
515 BFP T3 BR def
516 BFP HW Rel.
600 PoleDis. off
601 PoleDis.Start
602 PoleDis. L1
603 PoleDis. L2
604 PoleDis. L3
610 PoleDis. Trip
Table 5.3 Marshalling possibilities for signal relays and LEDs
Addr 1st display line
6200 MARSHALLING
6201 SIGNAL
RELAY 1
RELAY 1
6202 SIGNAL
RELAY 2
6203 SIGNAL
RELAY 3
6204 SIGNAL
RELAY 4
6205 SIGNAL
RELAY 5
6206 SIGNAL
RELAY 6
6207 SIGNAL
RELAY 7
6208 SIGNAL
RELAY 8
RELAY 8
Table 5.4 Preset annunciations for signal relays
60
Start of breaker failure protection for pole L1
Start of breaker failure protection for pole L2
Start of breaker failure protection for pole L3
Any delay time is running
Trip breaker failure protection during defect of the feeder breaker
Trip by breaker failure protection pole L1 (1st stage)
Trip by breaker failure protection pole L2 (1st stage)
Trip by breaker failure protection pole L3 (1st stage)
Trip by breaker failure protection three-pole (1st stage)
Trip breaker failure protection on local feeder breaker (1st stage)
Trip breaker failure protection on bus-bar breakers (2nd stage)
Transfer trip signal of breaker failure protection
Breaker failure protection blocked
Delay time T1 after single-pole trip expired
Delay time T1 after three-pole trip expired
Delay time T2 with current detection expired
Delay time T2 with CB auxiliary contact interrogation expired
Delay time for end fault protection expired
Delay time with defective circuit breaker expired
Release signal from hard-ware monitor present
Pole discrepancy supervision is switched off
Pole discrepancy supervision started (general)
Pole discrepancy supervision started for pole L1
Pole discrepancy supervision started for pole L2
Pole discrepancy supervision started for pole L3
Trip by pole discrepancy supervision
2nd display line
SIGNAL RELAYS
RELAY 1
BFP-Start
PoleDis.Start
RELAY 2
BFP CrossTrip
RELAY 3
BFP Trip BB
RELAY 4
BFP TransTrip
RELAY 5
Dev.operative
RELAY 6
BFP block
RELAY 7
BFP CBdefTrip
RELAY 8
Failure I
Failure Isymm
Description
FNo
Heading of the address block
Start of breaker failure protection or pole dis-
473
crepancy supervision
601
local trip command by breaker failure protec-
tion
506
Bus-bar trip command by breaker failure
507
protection
Transfer trip command by breaker failure
protection
508
Device operative; the NC contact of this relay
indicates "Device fault"
101
Breaker failure protection is blocked
509
Trip by breaker failure protection during de-
fect of the circuit breaker
515
Failure or disturbance in the measured quan-
151
tities
154
Installation instructions
Remarks
C53000---G1176---C91