Subscribe to Our Youtube Channel
Related Manuals for Sea Recovery Ultra Whisper Series
Summary of Contents for Sea Recovery Ultra Whisper Series
- Page 1 Ultra Whisper 400-600 Owner’s Manual Release Date: January, 2017 SYSTEM MODELS Ultra Whisper 400 Ultra Whisper 600 B651380001D | Revision: 01/01/17 Manual PN...
- Page 3 Ultra Whisper 400-600 Owner's Manual Manual PN B651380001D...
-
Page 5: Table Of Contents
Contents Chapter 1: About this Manual ................7 About Sea Recovery ............................. 7 Purpose ................................7 References ................................7 Graphics ................................7 Notice of Liability ..............................8 Trademarks ................................8 Terms and Conditions ............................8 Copyright ................................8 Revision History ..............................8 Chapter 2: Introduction .................. - Page 6 Chapter 7: Commissioning a New System ............37 New System Start-up Procedures ........................37 Pressure Changes ..............................39 Sea Recovery Ultra Whisper NEW SYSTEM INITIAL READINGS ..............40 Chapter 8: System Daily Operation ..............41 Day-to-Day Start-up Procedures for the Ultra Whisper System ................41 Controller Operations ............................
- Page 7 Chapter 10: Troubleshooting ................59 Error ID 1: High Pressure Fault ..........................59 Error ID 2: High Pressure Fault ..........................59 Error ID 3: Low Pressure Fault ..........................59 Error ID 4: Low Voltage Fault ..........................60 Loud or Whining Pump ............................60 Remaining Pressure in the System After Shut Down ...................
-
Page 9: Chapter 1: About This Manual
About Sea Recovery Since 1981, Sea Recovery Corporation has produced water desalination systems, used in various applications, for customers around the world. Currently, Sea Recovery Corporation stands apart as a leader in advanced water desalination systems for leisure marine applications. -
Page 10: Notice Of Liability
The information contained in the manual is distributed on an “as is” basis, without warranty. While every effort has been taken in the preparation of this manual, Sea Recovery Corporation shall not be held liable with respect to any liability, loss or damage caused by the instructions contained in this manual. The information contained in this manual is subject to change without notice. -
Page 11: Chapter 2: Introduction
Introduction Welcome Congratulations on your purchase of a new Sea Recovery Ultra Whisper Reverse Osmosis (RO) Desalination System! The Ultra Whisper RO Desalination System is a low power water maker, engineered for boaters with limited electrical options. The Ultra Whisper features automatic operation and is easy to use with its simple Start and Stop controls. -
Page 12: Models
Sea Recovery warrants that the Ultra Whisper RO Desalination System performs according to specifications for a period of 12 months from the date of shipment. Sea Recovery’s liability under this warranty is limited to repair or replacement of the Ultra Whisper RO Desalination System at Sea Recovery Corporation’s discretion. -
Page 13: Cleaning
In the event of a defect, a malfunction, or failure specifically covered by this warranty and during the warranty period, Sea Recovery Corporation will repair or replace, at its option, the product or component therein which upon examination by Sea Recovery Corporation appears to be defective. -
Page 14: Compliance
Compliance Sea Recovery’s Reverse Osmosis Desalination Systems Are Type Accepted by the American Bureau of Shipping, ABS. Sea Recovery’s Reverse Osmosis Desalination Systems comply with FCC § 15.105 Sea Recovery’s Reverse Osmosis Desalination Systems have been independently tested and determined to be in compliance with European CE (Conformité... -
Page 15: Chapter 3: System Specifications
Chapter System Specifications Feed Water and Recovery Important: If any of the following components are mismatched, the System will not function properly. The operating pressure and/or amperage draw will be higher than specified, causing damage to one or more components. The operating pressure can also be lower than required, resulting in low product water production and poor product water quality. -
Page 16: Performance
RO Membrane Element. External Installation Water Connections Pipe sizes to be supplied by the installer for connection of the Sea Recovery supplied components Feed Inlet: 1/2” MNPT Male National Pipe Thread U.S. Standard ... -
Page 17: Operating Amperage
System Specifications 115 and 230 VAC 60 Hz UW 400 UW 600 115V / 230V 115V / 230V Nominal Operating Amps 5.3/2.7 7.5/3.7 Maximum Motor Amps 6.6/3.5 8.6/4.3 Starting Amps 25/12.5 46/23 Horse Power Recommended Circuit Breaker 10/5 10/5 Minimum Size Power Wire AWG Minimum Size Power Wire mm2 110 and 220 VAC 50 Hz UW 400... - Page 18 Ultra Whisper 400-600...
-
Page 19: Chapter 4: System And Components Description
Chapter System and Components Description All components supplied by Sea Recovery, both standard and optional, are described in this chapter, along with items that the installer must provide. ALL STANDARD COMPONENTS AND ALL OPTIONAL ACCESSORIES. ** Denotes items supplied by installer... -
Page 20: Pressurization Components
Photographic Film Developing Industry. When used in sea water, they will plug much more rapidly (performance has shown within 1/10th of the time) than a Sea Recovery-supplied, Pre-filter cartridge element. This will cause frequent System shut downs and element replacement. -
Page 21: Product Water And Post-Filtration Components
System and Components Description 1. Brine Discharge Tee Connector allows for the Brine Discharge Hose to connect to the Thru Hull Over Board Discharge Fitting. 2. Thru Hull Discharge Fitting** should be installed above water level for discharge of the Brine Discharge Water from the System. -
Page 22: Electronic Components
Electronic Components The System’s electronic components measure water quality, control the direction of Product Water flow, Start and Stop the System, and contain the central electrical connection point. They also ensure only potable Product Water passes into the Product Water Storage Tank. 1. - Page 23 System and Components Description 3. Ensure all suction hose connections use two hose clamps rotated 180 degrees with the screw heads facing the same direction. Remove any flash on the hose-barb fittings using fine sandpaper. 4. Ensure all high-pressure hoses have sufficient slack and are not pulled tight into a sharp or immediate bend.
- Page 24 Ultra Whisper 400-600...
-
Page 25: Chapter 5: Pre-Installation Safety
Electrician’s tools available. No special system tools are required for installation. A separate TDS Meter, available from Sea Recovery, will assist in confirming System product water quality. A volt/ohm meter (VOM) is required for system installation and commissioning to ensure proper electrical power and connection. -
Page 26: System Safety Check
These chemicals destroy the copolymer components and the oxidants will damage the RO Membrane Element. In this situation, you can use the optional Sea Recovery Fresh Water Flush Accessory to remove the chlorine and bromine from your ship's potable water system before connecting the Ultra Whisper RO Desalination System. -
Page 27: Special Considerations
Components Supplied by the Installer or Owner Caution: All fittings, valves and piping installed prior to, within, and after the Sea Recovery Reverse Osmosis System must not contain iron; they must be non-ferrous material (not containing iron). Iron fittings or piping will cause rust fouling and failure of the RO Membrane Element. - Page 28 Caution: If the Sea Recovery RO System is connected to a Sea Chest or Stand Up Pipe, DO NOT plumb the Sea Recovery RO System feed line to the “top” of the Sea Chest or Stand Up Pipe. If plumbed into the top of these feed water arrangements, the Sea Recovery RO System will experience continual shut-down due to air inducement into the system.
-
Page 29: Chapter 6: Installation
Damage to any system component due to attachment to uneven surfaces is the responsibility and liability of the installer and is not covered by the Sea Recovery Warranty. -
Page 30: Electrical Connections
Sea Recovery Warranty. 7. The ***Freshwater Flush Filter Canister with attached Flush Pump is mounted in an accessible location to a vertical surface between an unpressurized line in the potable water system and the Freshwater Flush Check Valve. -
Page 31: Hose Lines
Installation 2. Connect main power using cable recommendations. The main power cable is inserted through one of the large strain reliefs on the side of the controller enclosure. 3. Connect the Feed Pump motor power through the other large strain relief on the side of the controller enclosure to terminals. - Page 32 1. Connect Feed and Freshwater Flush Lines with the supplied 20 feet (6 meters) of 1/2” (12.7 mm) I.D. Inlet Suction Hose. Secure the hose with two hose clamps offset 180 degrees at each fitting. Ignore any optional accessory that is not to be installed: Step from Outlet of: to Inlet of:...
-
Page 33: Ultraviolet (Uv) Light Installation
Installation Ultraviolet (UV) Light Installation The SP-Series UV unit is shipped with the UV lamp, quartz sleeve, fittings and O-rings and needs to be assembled before the UV unit can be used. 1. Install the UV unit in a sheltered, well-ventilated area. 2. -
Page 34: Connect Plumbing
Connect Plumbing Tube or hose ends must be cut squared and clean and have no rough edges. The quick fit elbow fitting has a C-clamp that will lock the tube in place once inserted. 1. Insert the supply pipe into one-cylinder port and label the port “Inlet.” 2. - Page 35 Installation • Before connecting the return tube, flush the unit to rinse out any debris left from the installation process. Danger: UV LIGHT EXPOSURE CAN SEVERELY BURN AND DAMAGE EYES AND SKIN. Danger: DO NOT look at the blue UV light. DO NOT operate the UV lamp outside of the UV treatment chamber.
-
Page 39: Chapter 7: Commissioning A New System
If the RO Membrane Element Serial Number tag is missing or does not contain a serial number and date, then immediately contact the company that sold the system to you or Sea Recovery. Provide Sea Recovery with the system serial number and model number of this Ultra Whisper System. - Page 40 If the system will not be operated within the next two weeks, perform a freshwater flush. If the Sea Recovery Automatic Freshwater Flush is installed, ensure that the potable water storage tank has potable water for the freshwater flush to utilize in rinsing the system.
-
Page 41: Pressure Changes
R.O Boost pump. If the R.O Boost pump becomes worn resulting in reduced pressure and/or flow, it may be returned to Sea Recovery for rebuild or replacement. Because of the specific matching requirements of the wear parts and tight tolerance, it is not practical to repair in... -
Page 42: Sea Recovery Ultra Whisper New System Initial Readings
Sea Recovery Ultra Whisper NEW SYSTEM INITIAL READINGS At the time of commissioning the NEW system, record the following information after one hour of continuous proper operation of the system. Retain this form in the Owner’s Manual for future reference and troubleshooting. This information is valuable to the servicing technicians in providing technical support to the owner and future operators of the Ultra Whisper System. -
Page 43: Chapter 8: System Daily Operation
1. Open any auxiliary valve within the incoming feed line, Outgoing Brine Discharge Line and Outgoing Product Water Line. Danger: Any auxiliary valve in these lines damages the Sea Recovery System if left closed during starting and/or operation of the system. -
Page 44: Controller Operations
Controller Operations Start/Stop button 1. Powers on and sets the system in its initial state. 2. When the system is producing water and the START/STOP button is pushed, the system stops all pumps and diverts water into the sea. 3. Resets all faults. Note that this button performs its designated action, regardless of whether or not you are browsing a menu. -
Page 45: Configuration (Change) Menu
System Daily Operation 4. Product Flow – Product water flow in l/min or GPM 5. Brine Flow – Brine flow in l/min or GPM 6. Water Quality – Salinity (water status) in ppm 7. Total Hours – High pressure pump/R.O. BOOST hour meter (counted in seconds but shown in whole hours) 8. -
Page 46: Fresh Water Flush Button
If the system will be operated within the next two weeks, no action is necessary besides winterization for freezing temperatures. c) If the system will not be operated within the next two weeks, perform a freshwater flush. If the Sea Recovery Automatic Freshwater Flush is installed, ensure that the potable water storage tank has fresh potable water for the freshwater flush to utilize in rinsing the system. -
Page 47: Maintenance Schedule
System Daily Operation If the freshwater flush assembly is installed, the freshwater flush will start 2 minutes after shut down. When the freshwater flush starts there will be a click and a green light will illuminate on the LCD screen. The time delay after shut down is to allow the R.O. - Page 48 Ultra Whisper 400-600...
-
Page 49: Chapter 9: System Storage And Cleaning
System by feeding Product Water into the System for a continuous 48-hour period. Caution: Never expose the RO Membrane Element to chemicals other than those supplied by Sea Recovery Corporation. Use caution when operating the system in harbors that may be polluted with chemicals, oil or fuel, as these chemicals may damage the RO Membrane Element beyond repair. -
Page 50: Automated Fresh Water Flush
minimum of 1 U.S. Gallons (3.8 Liters) per minute at minimum 30 PSI and maximum 75 PSI (minimum 2 Bar and maximum 5 Bar). If the Minimum of 1 U.S. Gallons (3.8 Liters) per minute at minimum 30 PSI (minimum 2 Bar) is not achieved, then the System may not fully flush the System with enough fresh water to displace the Feed Water (i.e., sea water). -
Page 51: Ro Membrane Element Cleaning Closed Loop
System Storage and Cleaning b) Disconnect the outlet line from the Sea Strainer and place it in the Rinse/Clean Solution Container. c) If the System is equipped with an Optional Inlet Rinse/Clean Valve between the Sea Strainer and Feed Pump, then position this valve to draw from the Rinse/Clean Solution Container. 3. - Page 52 2. Clean the Sea Strainer Mesh Screen. 3. Clean the Plankton Filter Element. 4. Clean (hose off) or replace 5-micron pre-filter elements with new 5-micron Sea Recovery pre-filtration elements. 5. Fill the Rinse/Clean Solution Container or a 5-gallon container with clean, fresh water.
-
Page 53: Long-Term Shutdown
3. Clean the Sea Strainer Mesh Screen. 4. Clean the Plankton Filter Element. 5. Replace the pre-filtration cartridges with new 5-micron Sea Recovery pre-filtration elements. 6. Fill the Rinse/Clean Solution Container with non-chlorinated product water. 7. Start the system. The rinse water rinses the entire system and discharge to waste. -
Page 54: Ro Membrane Element Cleaning
RO Membrane Element. If the RO Membrane Element is excessively fouled and in-field cleaning is not successful, the RO Membrane Element may be returned to Sea Recovery or to one of Sea Recovery’s many service dealers for professional chemical cleaning. If your membrane requires professional cleaning, please contact Sea Recovery for a return authorization number, price quotation and return instructions. - Page 55 System Storage and Cleaning fouling is minimized with freshwater rinsing whenever the system is not in use. 3. SRC MCC-2, Membrane Cleaning Compound "No. 2" is an acid cleaner designed to clean calcium carbonate and other mineral deposits from the RO Membrane Element. Mineral fouling is a slow process that takes place during use of the system.
- Page 56 Caution: Never expose the RO Membrane Element to chemicals other than those supplied by Sea Recovery Corporation. Use caution when operating the system in harbors that may be polluted with chemicals, oil or fuel, as these chemicals may damage the RO Membrane Element beyond repair.
-
Page 57: Closed Loop Configuration
System Storage and Cleaning 24. If the Clean/Rinse Outlet Valve is installed, position it to discharge out toward the brine discharge connector. 25. One final time, fill the Rinse/Clean Solution Container with non-chlorinated product water. 26. Start the system. The rinse water rinses the entire system and discharge to waste. 27. -
Page 61: Chapter 10: Troubleshooting
Chapter Troubleshooting Error ID 1: High Salinity Fault System produces expected product water flow with normal operating pressure after compensating for Feed Water Salinity and Temperature; however, the Product Water salinity is above 100ppm for more than 10 consecutive seconds. 1. -
Page 62: Error Id 4: Low Voltage Fault
• No kinks, blockages or air suction leaks in the inlet line The Feed Pump is operational and delivering flow and pressure Whether or not the Inlet Thru-Hull Fitting is clean (no manufacturing or installation debris) and if air suction leaks are present ... -
Page 63: 3-Way Product Water Diversion Valve Abnormalities
The R.O. BOOST, the RO Membrane Element and the Feed Pump output flow of water must all be matched. Upon leaving Sea Recovery’s factory at the time of shipment, these components have been matched and tested together as a system. -
Page 64: Product Water Abnormalities
lower size code from “B” to “A” or from “C” to “B” or “A,” then product water flow will not change but the operating pressure will increase. The High-Pressure Transducer will eventually signal the system to shut down due to excess pressure to the membrane. -
Page 65: Low Product Water Quality (Increase Of Salt Content In The Product Water)
Troubleshooting to maintain the normal product water production. The Ultra Whisper System self-adjusts by decreasing the operating pressure to compensate for higher-than-normal feed water temperature. Product water quality will decrease, or increase in salinity, as the operating pressure is decreased to compensate for the higher-than-normal feed water temperature. - Page 66 Ultra Whisper 400-600...
-
Page 67: Chapter 11: Electrical Information
Caution: Review the “Check Off Q.C. Sheet” that accompanied this Owner's Manual and the Invoice that accompanied this Ultra Whisper System to ensure that it has been configured from Sea Recovery for the appropriate and proper DC Voltage or AC Voltage, Cycles, and Phase. - Page 68 Electrical Information During start up, the current of the Feed Water Pump Alternating Current Electric Motor surges to “Locked Rotor” or “Starting Amps” amperage for a fraction of a second after which the Electric Motor begins to rotate. After the Electric Motor achieves full RPM rotation the current drops to normal running load.
- Page 69 12 and 24 VDC UW 400 UW 600 12V / 24V Minimum Size Power Wire mm2 13/8 13/8 115 and 230 VAC 60 Hz UW 600115V / 230V UW 400 115V / 230V Nominal Operating Amps 5.3/2.7 7.5/3.7 Maximum Motor Amps 6.6/3.5 8.6/4.3 Starting Amps...
- Page 70 Electrical Information Diameter Square Millimeters (mm Diameter Square Millimeters Inch Inch (In 0.2576 0.0521 6.5430 33.6069 0.2294 0.0413 5.8268 26.6516 0.2043 0.0328 5.1892 21.1385 0.1620 0.0206 4.1148 13.2913 0.1285 0.0130 3.2639 8.3626 0.1019 0.0082 2.5883 5.2588 0.0808 0.0051 2.0523 3.3064 0.0641 0.0032 1.6281...
-
Page 71: Chapter 12: Exploded Parts View
Chapter Exploded Parts View... -
Page 72: B001380001 Installation Kit
Exploded Parts View B001380001 INSTALLATION KIT ITEM NO. QTY. PART NUMBER DESCRIPTION 0112071900 ELB90 3/8MPTX1/2BARB NYL 0112021800 ELB90 3/8MPTX5/8BARB NYL 0204591869 CONN 3/8MPTX3/8TU PLASTIC 0204092469 CONN 3/8MPTX1/2TU PLASTIC 061172143016 SC HEX "A" 1/4X1"L 316SS 061080043000 WASHER FLAT 1/4 SS 05181434AA CLAMP HOSE 3/4 316SS B006380002 SEA STRAINER UW... -
Page 73: B006380002 Sea Strainer Uwdx 5In
B006380002 SEA STRAINER UWDX 5IN ITEM NO. QTY. PART NUMBER DESCRIPTION 20200402102 BRACKET SINGLE FILTER 0819245201 ELEMENT,100 MICRON, 5" 0713020973 FILTER HOUSING-LID 0.50 X 5 0112022500 ELB90 .50 MNPT x .62 BARB NYLON 061172143016 SCREW,HEX A,.25x1.00,SS 05181434AA HOSE CLAMP .75 SS 061170628016 SC PHIL PAN A #10 X 1 SS 065080028000... -
Page 74: B007300022 Feed Pump Assy Uw 400-12V
Exploded Parts View B007300022 FEED PUMP ASSY UW 400-12V ITEM NO. QTY. PART NUMBER DESCRIPTION 12176402DP PUMP ROTARY VANE 140GPH #15 12227601DP COUPLING PUMP-MOTOR SHAFT 12227701DP ADAPTER PUMP ROTARY VANE 15093110CF MOTOR .33HP 12 VDC 2115030120 RUBBER MOUNT 55 AQUA SERIES 0112022500 ELB90 .50 MNPT x .62 BARB NYLON 05181434AA... -
Page 75: B007300025Feed Pump Assy Uw 600-12V
B007300025 FEED PUMP ASSY UW 600-12V ITEM NO. QTY. PART NUMBER DESCRIPTION 12176404DP PUMP ROTARY VANE 215GPH #17 12227601DP COUPLING PUMP-MOTOR SHAFT 12227701DP ADAPTER PUMP ROTARY VANE 1516321100 MOTOR .5 HP DC, 12V 2115030120 RUBBER MOUNT 55 AQUA SERIES 0112022500 ELB90 .50 MNPT x .62 BARB NYLON 05181434AA HOSE CLAMP .75 SS... -
Page 76: B007300023 Feed Pump Assy Uw 400-24V
Exploded Parts View Exploded Parts View B007300023 FEED PUMP ASSY UW 400-24V ITEM NO. QTY. PART NUMBER DESCRIPTION 12176402DP PUMP ROTARY VANE 140GPH #15 12227601DP COUPLING PUMP-MOTOR SHAFT 12227701DP ADAPTER PUMP ROTARY VANE 15103210CF MOTOR .33HP 24 VDC 2115030120 RUBBER MOUNT 55 AQUA SERIES 0112022500 ELB90 .50 MNPT x .62 BARB NYLON 05181434AA... -
Page 77: B007300026Feed Pump Assy Uw 600-24V
B007300026 FEED PUMP ASSY UW 600-24V ITEM NO. QTY. PART NUMBER DESCRIPTION 12176404DP PUMP ROTARY VANE 215GPH #17 12227601DP COUPLING PUMP-MOTOR SHAFT 12227701DP ADAPTER PUMP ROTARY VANE 15163210CF MOTOR .5 HP DC, 24VDC 2115030120 RUBBER MOUNT 55 AQUA SERIES 0112022500 ELB90 .50 MNPT x .62 BARB NYLON 05181434AA HOSE CLAMP .75 SS... -
Page 78: B007300024Feed Pump Assy Uw 400-115-230Vac
Exploded Parts View B007300024 FEED PUMP ASSY UW 400-115-230VAC ITEM NO. QTY. PART NUMBER DESCRIPTION 12176402DP PUMP ROTARY VANE 140GPH #15 12227601DP COUPLING PUMP-MOTOR SHAFT 12227701DP ADAPTER PUMP ROTARY VANE 15AG250912 MOTOR .33 HP 50-60-1 2115030120 RUBBER MOUNT 55 AQUA SERIES 0112022500 ELB90 .50 MNPT x .62 BARB NYLON 05181434AA... -
Page 79: B007300027 Feed Pump Assy Uw 600-115-230Vac
B007300027 FEED PUMP ASSY UW 600-115-230VAC ITEM NO. QTY. PART NUMBER DESCRIPTION 12176404DP PUMP ROTARY VANE 215GPH #17 12227601DP COUPLING PUMP-MOTOR SHAFT 12227701DP ADAPTER PUMP ROTARY VANE 1519071010 MOTOR 1-2 HP 115-230 56C-1725 2115030120 RUBBER MOUNT 55 AQUA SERIES 0112022500 ELB90 .50 MNPT x .62 BARB NYLON 05181434AA HOSE CLAMP .75 SS... -
Page 80: B008220001 Plankton Filter Assy Uw-Se
Exploded Parts View B008220001 PLANKTON FILTER ASSY UW-SE ITEM NO. QTY. PART NUMBER DESCRIPTION 07650209ST FILTER HOUSING-LID AQUA ER 2020043810 BRACKET PLANKTON FILTER AQUA ER 0805823578 ELEMENT PLANKTON 0101072583 ELB90 0.50 MPT x 0.50 BARB 061172143016 SCREX,HEX A,.25x1.00,SS 05181434AA HOSE CLAMP .75 SS 061170628016 SC PHIL PAN A #10 X 1 SS 065080028000... -
Page 82: 0821003 Prod-Brine, Manif Assy, Uwiii
0821003 PROD-BRINE, MANIF ASSY, UWIII ITEM NO. QTY. PART NUMBER DESCRIPTION 07650209ST FILTER HOUSING-LID AQUA ER 11012061 BRACKET,MTG,FILTR ASSY,UW3M,AL 14012030 ORIFICE, ADAP, 0.5MTX0.25FT, ACETAL 0713020573 FILTER HOUSING-LID .375 X 10 ASM 0803004773 CHARCOAL FILTER 10IN 07650211ST HOUSING MODI, AIR-OIL, HP, 2.5X5, 0.5 FNPT 1401095998 SOLENOID VALVE EXTERNAL PORT 3131680298... - Page 83 Exploded Parts View SPARE PARTS PART NUMBER DESCRIPTION ORIFICE, ADAP, 0.5MTX0.25FT, ACETAL 14012030 FILTER, 5 MIC, 10 SQ FT, 2.5" H 9.75" 33-0117 0803004473 ELEMENT CARBON BRIQUETTE 5.0 IN 2614010473 ORING BLUE HSG...
-
Page 84: 0561009 Pump, Ro Boost, Assy, Uwiii
0561009 PUMP, RO BOOST, ASSY, UWIII ITEM NO. QTY. PART NUMBER DESCRIPTION 12181301DS ETD PUMP-NEW 2317100300 TRANSDUCER 0-2000 PSI .437 SAE 0112022500 ELB90 .50 MNPT x .62 BARB NYLON 0117492569 TEE ST .50 FT X .50 MT X .50 FT SS 0117630800 ADAPTER, .4375 FPT X .25 MPT 0204022569... -
Page 85: 0561015 Pump, Ro Boost, Mod, Assy, Uwiii
Exploded Parts View 0561015 PUMP, RO BOOST, MOD, ASSY, UWIII ITEM NO. QTY. PART NUMBER DESCRIPTION 20200404011 BRACKET L MOUNTING FEET-WHITE POWDER COAT 12181301DS ETD PUMP-NEW 2115030120 RUBBER MOUNT 55 AQUA SERIES 2317100300 TRANSDUCER 0-2000 PSI .437 SAE 0112022500 ELB90 .50 MNPT x .62 BARB NYLON 0117492569 TEE ST .50 FT X .50 MT X .50 FT SS 0117630800... -
Page 86: Membrane Vessel 400-600 Gpd Compact
MEMBRANE VESSEL 400 - 600 GPD COMPACT ITEM NO. QTY. PART NUMBER DESCRIPTION 0520210600 RETAINER PORT MVA 05202401GR BRACKET,MVA U-CLAMP,3 IN 2453502400 END PLUG SINGLE 3 AW 2453512400 END PLUG DUAL 3 IN AW 2615180100 FELT ADHESIVE 0.125 X 0.75 STRIP 0101370815 NIPPLE 0.25 NPT x 1.50 0117410800... - Page 87 Exploded Parts View B196300001 MEMBRANE VESSEL ASSY 200 GPD - EXPLODED...
-
Page 88: B196120015 Membrane Vessel Assy 600-2
B196120015 MEMBRANE VESSEL ASSY 600-2 ITEM NO. QTY. PART NUMBER DESCRIPTION 05202401GR BRACKET,MVA U-CLAMP,3 IN 2453502400 END PLUG SINGLE 3 AW 2417430800 INTERCONNECT MVA SS 0520051800-1 MVA RACK , UWDX BJ 0520210600 RETAINER PORT MVA 2408132500 VESSEL HIGH PRESSURE 450GPD 2724011233 MEMBRANE 450GPD AW W-SEAL 2615180100... - Page 89 Exploded Parts View...
-
Page 90: Membrane Vessel 400-600 Gpd Modular
MEMBRANE VESSEL 400 - 600 GPD MODULAR ITEM NO. QTY. PART NUMBER DESCRIPTION 0520051900 MVA RACK UW-SE 0520210600 RETAINER PORT MVA 05202401GR BRACKET,MVA U-CLAMP,3 IN 2453502400 END PLUG SINGLE 3 AW 2453512400 END PLUG DUAL 3 IN AW 2615180100 FELT ADHESIVE 0.125 X 0.75 STRIP 0101370815 NIPPLE 0.25 NPT x 1.50 0117410800... - Page 91 Exploded Parts View B196380001 MEMBRANE VESSEL ASSY 200 UWM- EXPLODED...
-
Page 92: Hp Hose Assembly
HP HOSE ASSEMBLY ITEM NO. QTY. PART NUMBER DESCRIPTION 2432160669 HOSE HP - 6P 1317481969 SWIVEL FITTING - 6 SSP Ultra Whisper 400-600... -
Page 93: 0821003 Prod-Brine, Manif Assy, Uwiii
Exploded Parts View 0821003 PROD-BRINE, MANIF ASSY, UWIII ITEM NO. QTY. PART NUMBER DESCRIPTION P502300003 MANIFOLD,FEED PRESSURE ASSY UW 14012006 MANIFOLD, PROB, PVC, PRESS, LOW, 6X1.5X2 5301181100 MANIF,FLOW METER,PVC 5360300800 MANIFOLD,BRINE FLOW,PVC,PRESS,LOW,1.5X1.5X4.0 0204011869 ELBOW,PP,3/8 ODx3/8 FT 11026520AO Turbo-Flowmeter 11026920AO FLOWMETER IN-LINE .53-7.9GPM 1401096100 VALVE SOLENOID 12VDC 3131680298... -
Page 94: 1401096100 3-Way Product Water Diversion Solenoid Valve
1401096100 3-WAY PRODUCT WATER DIVERSION SOLENOID VALVE PORT DESIGNATION & DESCRIPTION (WATER FLOW) Ultra Whisper 400-600... -
Page 95: B521220002 Charcoal Filter Assy 170-350-Uw
Exploded Parts View B521220002 CHARCOAL FILTER ASSY 170-350-UW ITEM NO. QTY. PART NUMBER DESCRIPTION 20200402102 BRACKET SINGLE FILTER 0713020573 FILTER HOUSING-LID .375 X 10 ASM 0803004773 ELEMENT CHARCOAL 10.0 01100719FX ELB9 0.375MPT X 0.50 BARBTEFBLU 0204020969 ELB90 .25 TUBE x .375 MPT PLASTIC 0204021869 ELBOW,SS,3/8 ODx3/8 MT 061170628016... -
Page 96: B561080001 Ph Neutralizer Assy 0.5-1.5 Gpm
B561080001 PH NEUTRALIZER ASSY 0.5-1.5 GPM ITEM NO. QTY. PART NUMBER DESCRIPTION 20200402102 BRACKET SINGLE FILTER 0713020573 FILTER HOUSING-LID .375 X 10 ASM 08251950AS ELEMENT POST FILTER PH 9.75 IN 0204020969 ELB90 .25 TUBE x .375 MPT PLASTIC 0204021869 ELBOW,SS,3/8 ODx3/8 MT 061172143016 SCREX,HEX A,.25x1.00,SS 061100043000... - Page 97 Exploded Parts View...
-
Page 98: B5262000Cv Uv Sterilizer
Exploded Parts View B5262000CV UV STERILIZER ITEM NO. QTY. PART NUMBER DESCRIPTION 20010418001A BRACKET MNT SADDLE UV-AW TOP 20010418002A BRACKET MNT SADDLE UV-AW BTTM 40000306CV UV STERILIZER 2 GPM 12VDC 0204021769 ELB90 .375 TUBE x .25 MNPT PLASTIC 0204091869 FITTING,PP,3/8 ODx3/8 MT 0254011000 ELB90 0.25 MPT X 0.50BARB NY 05181432AA... -
Page 100: B611220003 Remote Aw170 Uw Awii
Exploded Parts View B611220003 REMOTE AW170 UW AWII ITEM NO. QTY. PART NUMBER DESCRIPTION 31315606WE REMOTE TOUCH PAD 170 4900283104 CABLE MULTIST 8 CON WHT 3131100900 EZ PLUG RJ45 Ultra Whisper 400-600... -
Page 101: Available Tube And Fittings
AVAILABLE TUBES AND FITTINGS PART NO DESCRIPTION 1. CONNECTOR MALE 0204090669 1/4 inch tube x 1/8 inch mnpt 0204090869 1/4 inch tube x 1/4 inch mnpt 0204091669 3/8 inch tube x 1/8 inch mnpt 0204091769 3/8 inch tube x 1/4 inch mnpt 0204091869 3/8 inch tube x 3/8 inch mnpt 0204091969... - Page 102 Exploded Parts View PART NO DESCRIPTION 0204020969 1/4 inch tube x 3/8 inch mnpt 0204021769 3/8 inch tube x 1/4 inch mnpt 0204021869 3/8 inch tube x 3/8 inch mnpt 0204021969 3/8 inch tube x 1/2 inch mnpt 0204022069 3/8 inch tube x 3/4 inch mnpt 0204022469 1/2 inch tube x 3/8 inch mnpt 0204022569...
- Page 103 PART NO DESCRIPTION 0204212969 5/8 inch tube x 1/2 inch tube 0204213069 5/8 inch tube 9. UNION ELBOW 90 0204220869 1/4 inch tube 0204221769 3/8 inch tube x 1/4 inch tube 0204221869 3/8 inch tube 0204222569 1/2 inch tube 0204223069 5/8 inch tube 10.
-
Page 104: Tube Compression Fittings Replacement Parts
Exploded Parts View TUBE COMPRESSION FITTINGS REPLACEMENT PARTS ITEM DESCRIPTION PART NO. FOR 1/4" O.D. TUBE NUT/SPACER/GRAB & O-RING 1/4" 0204-1/469 TUBE 1/4 BLACK 0312121969 FOR 3/8" O.D. TUBE NUT/SPACER/GRAB & O-RING 3/8" 0204-3/869 TUBE 3/8 BLACK 0312123569 FOR 1/2" O.D. TUBE NUT/SPACE/GRAB &... -
Page 105: Chapter 13: Appendix
Chapter Appendix... - Page 112 PARKER WATER PURIFICATION 2630 E. EL PRESIDIO STREET CARSON CA United States 90810 Telephone: 310-608-5600 Fax: 310-608-5692 Email: waterpuriftcation@parker.com Web: www.parkcr.com Tier: 3 - Type Approved, unit certification not required covers the following: 2016 Mobile Offshore Drilling Unit Rules 4-2-1111.29, 4-2-217 & 6-1-5 National: International: Government:...
- Page 114 Sea Recovery Ultra Whisper Rev. A Sea Recovery’s Reverse Osmosis Desalination Systems comply with FCC § 15.105 United States Federal Communications Commission Compliance FCC § 15.105 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
- Page 115 System Warranty Registration Information INSTRUCTIONS: At the time of purchase of the Sea Recovery Reverse Osmosis Desalinator, please complete the warranty information listed below. After completing this form, please make a copy and mail it to the address provided at the bottom of this form.
- Page 116 Customer’s comments: ___________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________...
- Page 117 Sea Recovery ® Ultra Whisper ™ System Identi cation Information INSTRUCTIONS: It is important that this form is complete ly lled in at the time of purchase of the Sea Recovery Ultra Whisper Reverse Osmosis Desalinator. This information will be requested by our Service Department and Parts Order Desk whenever contacting Se a Recovery for technical assistance or by the Sales Department whenever ordering parts.
Need help?
Do you have a question about the Ultra Whisper Series and is the answer not in the manual?
Questions and answers