1. Manuals
  2. Brands
  3. Miele Manuals
  4. Hob
  5. ProLine CS 1013-1
  6. Operating and installation instructions

Miele CS 1013-1 Operating And Installation Instructions

Hide thumbs

Advertisement

Quick Links

Download this manual
Table of Contents
Operating and installation instructions
Gas hob
To avoid the risk of accidents or damage to the appliance it is essential
to read these instructions before it is installed and used for the first time.
en-SG, ZA
M.-Nr. 10 829 890

Advertisement

loading

  Also See for Miele CS 1013-1

Miele ProLine CS 1013-1 Operating And Installation Instructions
Miele ProLine CS 1013-1 Operating And Installation Instructions 60 pages
Miele CS 1028 G Operating And Installation Instructions
Miele CS 1028 G Operating And Installation Instructions 52 pages
Miele CS 1013-1 Operating And Installation Instructions
Miele CS 1013-1 Operating And Installation Instructions 48 pages

  Related Manuals for Miele CS 1013-1

  Summary of Contents for Miele CS 1013-1

  • Page 1 Operating and installation instructions Gas hob To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time. en-SG, ZA M.-Nr. 10 829 890...
  • Page 2 It is, however, set up for connection to the gas and electricity supplies in the countries specified. For trouble-free operation of the appliance, it is best to use it in the countries specified for use. For use in other countries, please contact Miele in your country.
  • Page 3 Gas-heated appliances Safety precautions to take if you smell gas  Turn off the gas emergency control valve immediately. This is usually located near the gas meter.  Eliminate all sources of ignition in a safe manner. Do not smoke, light cigarette lighters or matches. ...

  • Page 4: Table Of Contents

    Contents Warning and Safety instructions................ 6 Caring for the environment ................ 15 Guide to the appliance .................. 16 Hob........................16 Control knob......................17 Burner........................18 Before using for the first time ................ 19 Cleaning the hob for the first time................. 19 Switching on the hob for the first time ..............
  • Page 5 Contents Installation...................... 39 Electrical connection .................. 43 Gas connection.................... 45 Burner ratings ......................  48 Converting to another gas type .................  49 Jet table......................... 49 Changing the jets ....................50 Functional check ....................51 After sales service.................... 52 Contact in case of malfunction ................52 Data plate ......................

  • Page 6: Warning And Safety Instructions

    They contain important notes on installation, safety, use and maintenance. Miele cannot be held liable for damage caused by non-compliance with these instructions. Keep these instructions in a safe place and ensure that new users...
  • Page 7 Warning and Safety instructions Correct application  This hob is intended for domestic use and use in other similar environments.  This hob is not intended for outdoor use.  It is intended for domestic use only to cook food and keep it warm.
  • Page 8 Warning and Safety instructions Safety with children  Children under 8 years of age must be kept away from the hob unless they are constantly supervised.  Children 8 years and older may only use the hob unsupervised if they have been shown how to use it in a safe way and can recognise and understand the consequences of incorrect operation.
  • Page 9  Unauthorised installation, maintenance and repairs can cause considerable danger for the user. Installation, maintenance and repairs must only be carried out by a Miele authorised technician.  Do not use a damaged appliance. It could be dangerous. Check the hob for visible signs of damage.
  • Page 10 Warning and Safety instructions  Miele can only guarantee the safety of the appliance when genuine original Miele replacement parts are used. Faulty components must only be replaced by Miele spare parts.  The hob is not intended for use with an external timer switch or a remote control system.
  • Page 11 Warning and Safety instructions Correct use  The appliance gets hot when in use and remains hot for some time after being switched off. Do not touch the appliance if there is a possibility that it could still be hot. ...
  • Page 12 If the pan diameter is too large, flames can spread out to the sides and damage or burn the worktop, wall claddings or surrounding units and also parts of the cooktop. Miele cannot be held liable for this type of damage.
  • Page 13 Warning and Safety instructions  The pan support supplied with the appliance must always be used. Never place a pan on the burner itself.  Replace the pan supports carefully to avoid scratching the surface of the hob.  Do not use or store flammable materials near this hob. ...
  • Page 14 Warning and Safety instructions Cleaning and care  Do not use a steam cleaning appliance to clean this hob. The steam could reach electrical components and cause a short circuit.

  • Page 15: Caring For The Environment

    / recycling centre for electrical and electronic appliances, or contact your dealer or Miele for advice. You are also responsible (by law, depending on territory) for deleting any personal data that may be stored on the appliance being disposed of.

  • Page 16: Guide To The Appliance

    Guide to the appliance a Large burner Control knobs for the cooking zones b Normal burner e Rear c Pot rests f Front d Symbols to indicate which gas burner the control is for...

  • Page 17: Control Knob

    Guide to the appliance Control knob Symbol Description  Burner off, the gas supply is turned off  Largest flame  Smallest flame...

  • Page 18: Burner

    Guide to the appliance Burner n Burner cap o Burner head p Ignition safety device q Ignitor r Burner base...

  • Page 19: Before Using For The First Time

    Before using for the first time  Please stick the extra data plate for Switching on the hob for the the appliance supplied with this first time documentation in the space provided The metal components have a in the "After sales service" section of protective coating which when heated this booklet.

  • Page 20: Pans

    Pans – Any heat-resistant pans can be used Ø Pan [cm] on a gas burner. Burner Minimum base – Pans with thick bases are preferable diameter as these distribute heat more evenly. Normal burner With thin bases, there is a danger of food overheating in places.

  • Page 21: Tips On Saving Energy

    Tips on saving energy – Use a pan lid whenever possible to minimize heat loss. – Wide, shallow pans are preferable to tall, narrow ones. They will heat up faster. – Cook with as little water as possible. – Reduce the size of the flame once the water has come to the boil or the oil is hot enough to fry in.

  • Page 22: Operation

    Operation Adjusting the flame  Fire hazard. Do not leave the appliance The burners can be regulated at any unattended whilst it is being used. level between the strongest and weakest flame. Switching on As the outer part of the flame is much ...

  • Page 23: Safety Features

    Safety features Thermo-electric flame failure monitor This hob has a thermo-electric flame failure monitor. If the flame goes out, for example because food has boiled over or if there has been a sudden draught, the supply of gas to the burner will be cut off.

  • Page 24: Cleaning And Care

    Cleaning and care  Allow the CombiSet to cool down Danger of burning. before cleaning. The burners must be switched off. The hob needs to cool down.  The CombiSet and accessories should be cleaned after each use.  Danger of injury. ...

  • Page 25: Stainless Steel Frame/Control Panel

    Stubborn soiling should be soaked  Finally, dry with a clean soft cloth. first.  Dry the control(s) with a clean cloth. Tip: The Miele conditioning agent for stainless steel can be used after cleaning to help keep your appliance looking good (see "Optional accessories").

  • Page 26: Pan Supports

    Cleaning and care Pan supports Burner Do not clean the pan supports in a Do not clean any parts of the burner dishwasher. in a dishwasher.  Remove the pan supports.  The burner should be dismantled and then cleaned by hand using a ...
  • Page 27 Cleaning and care Assembling the burner  Place the burner head  on the burner base  so that the ignition safety device  and the ignitor  extend through their respective holes in the burner head. The burner head must click into place correctly.

  • Page 28: Problem Solving Guide

    Problem solving guide Many malfunctions and faults that can occur in daily operation can be easily remedied. Time and money will be saved because a service call will not be needed. The following guide may help you to find the reason for a malfunction or a fault, and to correct it.
  • Page 29 The mains fuse has tripped. burner does not spark.  You may need to contact a registered electrical worker or Miele. There is food residue stuck between the ignitor and the burner cap. There is food residue on the thermocouple.

  • Page 30: Optional Accessories

    Helps keep the appliance looking These products can be ordered through good for longer. the Miele Webshop. These can also be ordered from Miele (see end of this booklet for contact details) or from your Miele dealer. Ceramic and stainless steel...

  • Page 31: Safety Instructions For Installation

    Safety instructions for installation Fit the wall units and cooker hood before fitting the CombiSet to avoid damaging it.  The veneer or laminate coatings of worktops (or adjacent kitchen units) must be treated with 100 °C heat-resistant adhesive which will not dissolve or distort.

  • Page 32: Safety Distances

    Safety distances Safety distance above the Safety Distance below the CombiSet CombiSet There should be at least 30 mm height or plenty of space reserved below the CombiSet for the installation of the flexible gas connection pipe and electrical cable. It also avoids any possible hindrance towards the movement of all moveable kitchen parts (e.g.
  • Page 33 CS 1112 CS 1122 CS 1134 CS 1326 CS 1327 CS 1411 100 mm CS 1012 / CS 1012-1 CS 1013 / CS 1013-1 150 mm CS 1421 Not recommended CS 1312 CS 1322 200 mm CS 1034 / CS 1034-1...
  • Page 34 Safety distances Safety distance when installing the appliance near a wall with additional niche cladding A minimum safety distance must be maintained between the worktop cut-out and any niche cladding to protect it from heat damage. If the niche cladding is made from a combustible material (e.g. wood) a minimum safety distance ...

  • Page 35: Installation Notes

    Installation notes Seal between the CombiSet Tiled worktop and the worktop Grout lines  and the hatched area underneath the CombiSet frame must be smooth and even. If they are not the Do not use sealant between the CombiSet will not sit flush with the CombiSet and the worktop.

  • Page 36: Building-In Dimensions

    Building-in dimensions a Spring clamps b Front c Building-in depth d Mains connection box with mains connection cable, L = 1440 mm e Gas connection R 1/2...

  • Page 37: Building-In Several Combisets

    Building-in several CombiSets Example: 3 CombiSets a Spring clamps b Spacer bars c Gaps between spacer bars and worktop d Cover strips e CombiSet width minus 8 mm f CombiSet width g CombiSet width minus 8 mm h Worktop cut-out...
  • Page 38 Building-in several CombiSets Calculating the worktop cut-out The frames of the CombiSets overlap the worktop at the outside right and left by 8 mm on each side.  Add up the widths of the CombiSets and subtract 16 mm from this figure. Example: 288 mm + 288 mm + 380 mm = 956 mm - 16 mm = 940 mm The CombiSets are 288 mm, 380 mm or 576 mm wide depending on model (see...

  • Page 39: Installation

    Installation Preparing the worktop  Make the worktop cut-out as shown in "Building-in dimensions" or as calculated (see Building-in several CombiSets). Observe the safety distances (see "Safety distances"). Wooden worktops  Seal the cut surfaces with a suitable sealant to avoid swelling caused by moisture.
  • Page 40 Installation Natural stone worktops You will need heavy duty double-side tape (not supplied) to secure the spring clamps and spacer bars.  Apply silicone to the side and lower edges of the spring clamps  and the spacer bars .  Then fill gap  between spacer bar ...
  • Page 41 Installation Building in several CombiSets Installing the CombiSet  Push the built-in CombiSet to the  Feed the mains connection cable side until the holes in the spacer bar down through the cut-out. can be seen.  Starting at the front, position the CombiSet in the worktop cut-out.
  • Page 42 Installation Connecting the CombiSet Removing the CombiSet  Connect the CombiSet to the  If the CombiSet can be accessed electricity and gas supplies (see "Gas from below, push it out from below. connection"). Push the rear side out first. ...

  • Page 43: Electrical Connection

     Danger of injury. The wires in the mains lead are coloured in accordance with the Miele cannot be held liable for following code: unauthorised installation, Green/yellow = earth maintenance and repair work as this Blue = neutral can be dangerous to users.
  • Page 44 If the mains cable needs to be replaced following depending on installation: it must be replaced with a special connection cable, type H 05 VV-F (PVC- Safety fuses insulated), available from Miele.  Completely remove fuses The connection data is quoted on the data plate. Automatic circuit breakers ...

  • Page 45: Gas Connection

    Gas connection  Connection to the gas supply must According to the Gas Safety be carried out in strict accordance (Registration of Gas Installers and with current local regulations. Every Gas Contractors) Regulations, any appliance should have its own easily gas installation work including the accessible isolating valve and test installation of appliances and...
  • Page 46 Please appropriate class and is employed contact your supplier or Miele for the by a registered gas contractor. appropriate conversion jets if necessary. Conversion to another type of gas is described under "Conversion...
  • Page 47 Gas connection LPG Gas Connection - elbow joint connection a Elbow join b Gasket c Nozzle d Ring e Rubber hose The gasket depicted above is to prevent gas leakage.

  • Page 48: Burner Ratings

    Burner ratings Nominal ratings Burner Gas type Highest setting Lowest setting Medium Natural gas – 0.35 burner Liquefied Petroleum gas 0.35 Town gas – 0.35 Large burner Natural gas – 0.50 Liquefied Petroleum gas 0.50 Town gas – 0.50 Total Natural gas –...

  • Page 49: Converting To Another Gas Type

    Converting to another gas type  Conversion from one type of gas to another, should only be undertaken by an approved and registered gas installer in strict accordance with current local and national safety and building regulations. Disconnect the hob from the electricity supply and turn off the gas supply.

  • Page 50: Changing The Jets

    Converting to another gas type To change the small jet Changing the jets The upper part of the appliance has to  Disconnect the hob from the be removed before the small jet can be electricity supply and turn off the gas changed.

  • Page 51: Functional Check

    Converting to another gas type Functional check  Check all gas fittings for leaks.  Reassemble the hob.  Ignite all burners to check that they are operating correctly. – The flame must not go out on the lowest setting, or when the control is turned quickly from the highest to the lowest setting.

  • Page 52: After Sales Service

    In the event of any faults which you cannot remedy yourself, please contact your Miele Dealer or Miele Service. Contact information for Miele Service can be found at the end of this document. Please note that telephone calls may be monitored and recorded for training purposes and that a call-out charge will be applied to service visits where the problem could have been resolved as described in this booklet.
  • Page 55 Singapore: Miele Pte. Ltd. 163 Penang Road # 04 - 03 Winsland House II Singapore 238463 Tel: +65-67351191 Fax: +65-67351161 E-Mail: info@miele.com.sg Internet: www.miele.sg South Africa: Miele (Pty) Ltd 63 Peter Place, Bryanston 2194 P.O. Box 69434, Bryanston 2021 Tel.: (011) 875 9000, Fax: (011) 875 9035 Internet: www.miele.co.za...
  • Page 56 CS 1013-1  en-SG, ZA M.-Nr. 10 829 890 / 00...

This manual is also suitable for:

Cs 1018 g

Table of Contents