Download Print this page

Miele CS 1012-1 Operating And Installation Instructions

Gas hobs.
Hide thumbs

Advertisement

Operating and installation instructions
Gas hobs
CS 1012-1
CS 1034-1
en - GB
To avoid the risk of accidents or
damage to the appliance it is
essential to read these
instructions before it is installed
and used for the first time.
M.-Nr. 09 094 640

Advertisement

   Summary of Contents for Miele CS 1012-1

  • Page 1

    Operating and installation instructions Gas hobs CS 1012-1 CS 1034-1 en - GB To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time.

  • Page 2

    Per questo se si vuole usare l’apparecchio in un paese diverso rivolgersi al servizio di assistenza tecnica Miele del paese in cui si intende usarlo.

  • Page 3: Table Of Contents

    CS 1012-1 ........

  • Page 4

    CS 1012-1 ........

  • Page 5

    Gas-heated appliances Safety precautions to take if you smell gas ß Turn off the gas emergency control valve immediately. This is usually located near the gas meter. ß Eliminate all sources of ignition in a safe manner. Do not smoke, light cigarette lighters or matches. ß...

  • Page 6: Guide To The Appliance

    Guide to the appliance CS 1012-1 a Large burner Controls: b Medium burner f rear c Pan support g front d Symbols to indicate which gas burner the control is for e Display Display l In-operation indicator m Residual heat indicator...

  • Page 7: Cs 1034-1

    Guide to the appliance CS 1034-1 a Large burner Controls: b Small burner h front right c Large burner i rear right d Medium burner j rear left e Pan supports k front left f Symbols to indicate which gas burner the control is for g Display Display...

  • Page 8

    Guide to the appliance Burner n Burner cap o Burner head p Ignition safety device q Ignitor r Burner base...

  • Page 9: Warning And Safety Instructions

    Warning and Safety instructions This appliance complies with all current local and national safety requirements. Improper use can, however, present a risk of both personal injury and material damage. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before installation and before using it for the first time.

  • Page 10

    The hob is intended for domestic use only to cook food and keep it warm. Any other use is not supported by the manufacturer and could be dangerous. Miele cannot be held liable for damage resulting from incorrect or improper use or operation.

  • Page 11

    Warning and Safety instructions Safety with children The hob is not a toy! To prevent the risk of injury, do not let children play with the appliance or its controls. Children under 8 years of age must be kept away from the hob unless they are constantly supervised.

  • Page 12

    Miele cannot be held liable for the consequences of an inadequate earthing system (e.g. electric shock). Before connecting the hob to the mains electricity...

  • Page 13

    Miele cannot be held liable for damage caused by incorrect installation or connection.

  • Page 14

    While the hob is under guarantee, repairs should only be undertaken by a service technician authorised by Miele. Otherwise the guarantee is invalidated. Faulty components must only be replaced by genuine Miele original spare parts. The manufacturer can only guarantee the safety of the appliance when Miele replacement parts are used.

  • Page 15

    Warning and Safety instructions In areas which may be subject to infestation by cockroaches or other vermin, pay particular attention to keeping the appliance and its surroundings clean at all times. Any damage which may be caused by cockroaches or other vermin will not be covered by the guarantee.

  • Page 16

    Warning and Safety instructions Use heat-resistant pot holders or gloves when using the hob. Ensure that they do not come into contact with the flames. Do not use large cloths, tea towels or similar as the ends could touch the flames and catch fire.

  • Page 17

    Miele cannot be held liable for this type of damage. Ensure that the flames from the burner do not spread out beyond the base and up the sides of the pan.

  • Page 18

    Warning and Safety instructions Using the hob will cause a build-up of heat and moisture in the room in which it is installed. Ensure that the room has sufficient natural or mechanical means of ventilation, e.g. an extractor. If the hob is used for very long periods of time additional ventilation of the room may be necessary, e.g.

  • Page 19

    If the hob has not been used for a long period of time it should be thoroughly cleaned before it is used again. It is also advisable to have the appliance tested for safety. Miele cannot be held liable for damage caused by non-compliance with these Warning and Safety instructions.

  • Page 20: Caring For The Environment

    Caring for the environment Disposal of the packing Disposal of your old appliance material Electrical and electronic appliances often contain materials which, if The transport and protective packing handled or disposed of incorrectly has been selected from materials which could be potentially hazardous to are environmentally friendly for human health and to the environment.

  • Page 21: Before Using For The First Time

    Before using for the first time Please stick the extra data plate for the appliance supplied with this documentation in the space provided in the "After sales service, data plate, guarantee" section of this booklet. Cleaning for the first time ^ Remove any protective foil and stickers.

  • Page 22: Operation

    Operation Rapid ignition system Switching on, adjusting the flame and switching off The appliance is supplied with a rapid ignition system with the following The control is used to ignite the burner features: and to regulate the strength of the flame.

  • Page 23

    Operation Switching on Regulating the flame The burners can be regulated at any level between the strongest and weakest flame. Control the flame so that it does not spread out beyond the sides of the pan. As the outer part of the flame is much hotter than the centre, the tips of ^ To ignite the burner press the control the flames should stay beneath the pan...

  • Page 24: In-operation Indicator And Residual Heat Indicator

    Operation In-operation indicator and Residual heat indicator When a gas burner is switched on, the relevant in-operation indicator lights up. Once it has reached a certain temperature, the residual heat indicator also lights up. The in-operation indicator goes out when the gas burner is switched off.

  • Page 25: Suitable Pans

    Suitable pans – Select pans which are suitable for the burner they are to be used on. In Burner Min. pan base diameter general: use larger diameter pans on in cm the large burners, and smaller Small burner diameter pans on the small burners. Medium burner –...

  • Page 26: Energy-saving Tips

    Energy-saving tips – Use a pan lid whenever possible to minimise heat loss. – Cook with as little water as possible. – Cooking times are greatly reduced when using a pressure cooker. – Turn the flame down promptly to a lower setting when the pan has come to the boil.

  • Page 27: Safety Features

    Safety features Thermo-electric ignition Safety cut-out This appliance has a thermo-electric If a burner has been used for an ignition safety device. If the flame goes unusually long period (approx. 4 out, for example if food has boiled over hours), it will switch off automatically. or if there is a sudden draught, and To use the burner again, turn the automatic re-ignition has been...

  • Page 28: Cleaning And Care

    Cleaning and care Miele offer a range of branded cleaning To avoid damaging the surface or and conditioning agents for your hob. your hob, do not use: See "Optional accessories". – cleaning agents containing soda, alkalines, ammonia, acids or Do not use a steam cleaning chlorides, appliance to clean this appliance.

  • Page 29: Stainless Steel Surfaces

    Do not use the Miele ceramic and stainless steel hob cleaning agent on the printed flame symbols. This would rub off the print.

  • Page 30: Burner

    Cleaning and care Burner Reassemble the burner Do not clean any parts of the burner in a dishwasher. The burner should be dismantled and then cleaned by hand using a solution of warm water and a little washing-up liquid applied with a soft sponge. Parts of the burner that cannot be removed should be wiped clean with a damp cloth only.

  • Page 31: Problem Solving Guide

    Problem solving guide ... there has been a power cut. Repairs to the gas and electrical Turn all the controls clockwise to the "ß" components of this appliance must position. You can then operate the only be carried out by a suitably appliance as normal.

  • Page 32

    ..the ignitor on the burner does not spark. Check whether – the mains fuse has tripped. If it has, contact a qualified electrician or the Miele Service Department. – food deposits have lodged themselves between the ignitor and the burner cap. Remove any food deposits carefully (see "Cleaning and care").

  • Page 33: Optional Accessories

    Optional accessories Miele offer a comprehensive range of useful accessories as well as cleaning and conditioning products for your Miele appliances. These can be ordered online at: or from Miele (see back cover for contact details) Ceramic and stainless steel hob cleaner 250 ml...

  • Page 34: Safety Instructions For Installation

    A gas hob must not be installed above a fridge, fridge freezer, freezer, dishwasher, washing machine or tumble dryer. The hob may only be installed above a Miele oven if the worktop is at least 40 mm thick.

  • Page 35

    Safety instructions for installation Safety distance above the appliance A minimum safety distance must be maintained between the appliance and the cooker hood above it. See the cooker hood manufacturer's operating and installation instructions for details. If the manufacturer's instructions are not available for the cooker hood, a minimum safety distance of at least 760 mm must be maintained.

  • Page 36

    50 mm CS 1112 CS 1122 CS 1134 CS 1326 CS 1327 CS 1411 100 mm for CS 1012 / CS 1012-1 150 mm for CS 1421 CS 1312 Not allowed CS 1322 200 mm for CS 1034 / CS 1034-1...

  • Page 37

    Safety instructions for installation Safety distance when installing the appliance near a wall with additional niche cladding A minimum safety distance must be maintained between the worktop cut-out and any niche cladding to protect it from heat damage. If the niche cladding is made from a combustible material (e. g. wood) a minimum safety distance e of 50 mm must be maintained between the cut-out and the cladding.

  • Page 38: Appliance And Building-in Dimensions

    Appliance and building-in dimensions CS 1012-1 a Spring clamps b Front c Casing depth d Casing depth including the mains connection box with mains connection cable, L = 1440 mm e Casing depth including the gas connection R 1/2 - ISO 7-1 (DIN EN 10226)

  • Page 39: Cs 1034-1

    Appliance and building-in dimensions CS 1034-1 a Spring clamps b Front c Casing depth d Casing depth including the mains connection box with mains connection cable, L = 1440 mm e Casing depth including the gas connection R 1/2 - ISO 7-1 (DIN EN 10226)

  • Page 40: Preparing The Worktop

    Preparing the worktop ^ Make the worktop cut-out for one or more appliances in accordance with the building-in diagrams. Remember to maintain the minimum safety distance from the back wall, as well as from any tall unit or side wall to the right or left of the hob. See "Safety instructions for installation".

  • Page 41: Installation Of Several Appliances

    Installation of several appliances When installing two or more appliances next to each other a spacer bar b must be used between each one. See "Fixing the spring clamps and spacer bars". Worktop cut-out Worktop cut-out - two appliances - three appliances To calculate the cut-out width (D) required: Add up the widths of each appliance (e.g.

  • Page 42

    Installation of several appliances a Spring clamps b Spacer bars c Gaps between spacer bars and worktop d Cover strips The illustration shows a worktop cut-out with spring clamps a and spacer bars b for 3 appliances. An additional spacer bar is required for each additional appliance. The position for securing each additional spacer bar will depend on the width of appliance B (288 mm / 380 mm / 576 mm).

  • Page 43: Fixing The Spring Clamps And Spacer Bars

    Fixing the spring clamps and spacer bars Wooden worktops ^ Position the spring clamps supplied a and spacer bars b on the top edge of the cut-out in the positions marked. ^ Secure the spring clamps and spacer bars with the 3.5 x 25 mm screws supplied.

  • Page 44

    Fixing the spring clamps and spacer bars Granite and marble worktops The screws are not required for granite or marble worktops. ^ Apply silcone to the side edges and the lower edges of spring clamps a and spacer bars b. ^ Then fill gap e between the spacer ^ Position and secure the spring bars and the worktop with silicone.

  • Page 45: Installing / Removing The Appliance

    Installing / removing the appliance ^ Starting at the front, position the next Installing the appliance appliance in the worktop cut-out. ^ Feed the connection cable down ^ Connect the appliance(s) to the through the cut-out. mains (see "Electrical connection") ^ Starting at the front, position the and to the gas supply (see "Gas appliance in the worktop cut-out.

  • Page 46: General Installation Tips

    General installation tips Seal between the appliance and the Tiled worktop worktop Grout lines a and the hatched area The sealing strip under the edge of the underneath the surface of the top part of the appliance provides a appliance must be smooth and even. If sufficient seal for the worktop.

  • Page 47: Electrical Connection

    H 05 V V-F be provided for all poles. (pvc insulated), available from Miele. For extra safety it is advisable to protect the appliance with a suitable residual Installation, repairs and other work current device (RCD).

  • Page 48

    Electrical connection Important The electrical safety of this appliance can only be guaranteed when continuity is complete between it and an effective earthing system, which complies with current local and national safety regulations. It is most important that this basic safety requirement is present and regularly tested and where there is any doubt, the electrical wiring in the home should be tested by a...

  • Page 49: Gas Connection

    Please contact your dealer or the Miele Spare Parts Department for the Check with your local gas supplier appropriate conversion jets if about the type of gas and its necessary.

  • Page 50

    Gas connection Connection The gas connection must be installed so that connection can be made either from inside or outside the kitchen unit, and the isolating valve must be easily accessible and visible (by opening one of the kitchen doors, if necessary). After installing the appliance the gas burners have to be set for local conditions.

  • Page 51: Conversion To Another Type Of Gas

    Medium burner 1.00 0.42 Large burner 1.28 0.52 have to be changed. Liquid gas CS 1012-1 Medium burner 0.67 0.27 Large burner 0.87 0.32 Nominal rating at high setting The jet markings refer to 1/100 mm of the jet diameter.

  • Page 52: Jet Table

    Conversion to another type of gas CS 1034-1 Screw in the new jets according to the following table. Nominal rating at high setting Jet table Gas type For UK and IE Small burner Natural gas H 1.00 Liquid gas 1.00 / 73 g/h Main jet Small jet Medium...

  • Page 53: Changing The Jets

    Conversion to another type of gas Changing the jets Disconnect the gas hob from the mains electricity supply. Turn off the gas supply. To change the main jets ^ Carefully remove the upper section of the appliance. When doing this make sure you do not also pull out the light unit for the display located...

  • Page 54: Function Test

    Conversion to another type of gas Function test Check all gas fittings for leaks. ^ Reassemble the appliance. ^ Check the burner flame by operating the burner. The flame must not go out on the lowest setting, or when the control is turned quickly from a high to a low setting.

  • Page 55: After Sales Service, Data Plate, Guarantee

    Please note that telephone calls may be monitored and recorded to improve our service. When contacting Miele, please quote the model and serial number of your appliance which are given on the data plate. N.B. A call-out charge will be applied for service visits where the problem could have been resolved as described in these instructions.

  • Page 56

    Alteration rights reserved/ 4111 M.-Nr. 09 094 640 / 01...

This manual also for:

Cs 1034-1

Comments to this Manuals

Symbols: 0
Latest comments: