Oki MC160MFP Maintenance Manual page 201

Oki Data CONFIDENTIAL
Code
Modem can not ready within 10 seconds after entering primary channel in V.34.
00BC
Can not detect correct V.21 or JM signal after detected FSK frequency.
00BD
Remote side no document to be polled after V8 handshaking.
00BE
00BF Capability no match.
Remote side disconnect before entering primary channel in V.34.
00C0
At phase-D, transmitting units out EOP 3 times consecutively, but receive no answer from
00C1
receiving unit.
Remote side disconnect after sending out V.8 CM signal.
00C2
00C4 After sending MPS signal, the received is not one of MCF, RTN, PIP, PIN, RTP, DCN.
00C5 Received DCN signal after sending MPS signal.
00C9 At phase-D, sending MPS 3 times consecutively, but no answer from receiving unit.
00CA After sending EOP signal, the received is not one of MCF, RTN, PIP, PIN, PRI-EOP, DCN.
00CB After sending EOP signal, the received is DCN signal.
00CC After sending EOM signal, the received is not one of MCF, RTN, PIP, PIN, RTP, DCN.
00CD At phase-D, transmitting units out EOM 3 times consecutively, but receive no answer.
00CE At phase-D, transmitting units out EOM, but receive DCN.
Received incorrect signal after sending DTC signal for V.34 polling.
00CF
00D0 Received ERR signal after sending EOR_NULL.
Received incorrect response after sending PPS_EOP signal in V.34.
00D1
00D2 Received DCN after sending PPS_EOP signal.
00D3 Received DCN after sending PPS_NULL signal.
00D4 Received DCN after sending PPS_EOM signal.
00D8 Can not detect correct phase 3 signal for polling within 25 seconds.
00D9 Can not detect correct phase 3 signal after detect silence after phase 2.
00DA Can not detect phase 4 signal within 30 seconds or remote side hang up over 6 seconds.
00DB Can not received any T.30 signal within 15 seconds within phase 4.
00DC Received T.30 signal in phase 4 other than DCS, DIS or DTC.
Remote side no SUB capability in V.34.
00DE
00E0 At phase-D, transmitting units out PPS_NULL 3 times consecutively but receive not answer.
00E1 Received incorrect response after sending PPS_NULL.
00E2 Can not receive any response in RR response procedure after sending PPS_NULL.
00E4 At phase-D, transmitting units out PPS_MPS 3 times consecutively but receive no answer.
00E5 Received incorrect response after sending PPS_MPS.
00E6 Can not receive any response in RR response procedure after sending PPS_MPS.
00E7 Received DCN after sending PPS_MPS.
00E8 At phase-D, transmitting units out PPS_EOP 3 times consecutively but receive no answer.
00E9 Receive PIN signal after sent last page three times.
00EA Can not receive any response in RR response procedure after sending PPS_EOP.
00EB At phase-D, transmitting units out PPS_EOM 3 times consecutively but receive no answer.
00EC Received incorrect response after sending PPS_EOM.
00ED Can not receive any response in RR response procedure after sent out PPS_EOM.
00EE At phase-D, transmitting units out EOR_NULL 3 times consecutively but receive no answer.
44292401TH Rev.1
Possible Causes of Error. Code Possible Causes of Error.
00EF Received incorrect response after sending EOR_NULL.
00F0 Can not receive any response procedure after sending EOR_NULL.
00F1 At phase-D, transmitting units out EOR_MPS 3 times consecutively but receive no answer.
00F2 Received incorrect response after sending EOR_MPS.
00F3 Received ERR signal after sending EOR_MPS.
00F4 Can not receive any response in RR response procedure after sending EOR_MPS.
00F5 At phase-D, transmitting units out EOR_EOP 3 times consecutively but receive no answer.
00F6 Received incorrect response after sending EOR_EOP.
After Received ERR, our side can not received response after sending EOR_EOP com-
00F7
mand.
00F8 At phase-D, transmitting units out EOR_EOM 3 times consecutively but receive no answer.
00F9 Received incorrect response after sending EOR_EOM.
00FA Received ERR signal after sending EOR_EOM.
00FB Can not receive any response in RR response procedure after sending EOR_EOM.
00FC Can not receive any response after sending CTC.
00FD Can not speed down to lower speed in ECM mode.
00FE Memory full for transmission.
00FF Redail all fail.
TROUBLESHOOTING
200 /