Oki MC160MFP Maintenance Manual page 138

Oki Data CONFIDENTIAL
14.2.2 Soft switch list
15.2.2 Soft switch list
Soft Switch No. Bit No.
V.34 CI signal byte number
#01 2/1
8/7 Time between phase C to phase D signal in V.17
#02 6 Header TX selection open to user
3/2 Transmit RTN signal level criteria
8
Send out NSF frame with station ID
7 Number of Pause within phone number
#03
6 Re-dial prohibit for NO ANSWER
4/3/2/1 RX level setting
Visible alarm for RTN signal
4
#04
3 Audible alarm for RTN signal
8/7
Push button ON/OFF Timing (PB)
6/5 Relation between 10 key # & No.of dial pulse
#05
3 10PPS/20PPS
2/1 PPS ratio
8/7
Ring on time to ignore ring off time at 1st cycle
#06
4/3 Ring off time at 1st cycle to approve incoming ring
8
Dial tone or busy tone detection
7 PSTN/PBX setting
#07 6 PBX dial tone detect
5 Dial mode select
4/3/2/1 TX level select for PSK/FSK
7 Detect busy tone after dialing
#08
6 Sending CED signal after connection
8/7
Ringer frequency detection
TSI/CSI append "+"
#09 5
2/1 Time from RX DIS signal to send DCS signal
8
Print out RTN page report
7 Confirmation report result field
6/5 Get gap time between digit for pulse dial
#10 4 RX PIP T.30 command after send out MPS command
3 Received DIS signal within reception
2 Transmission time limitation
1 Audio alarm after communication fail
7 Detect dial tone after pre-fix number
6 Pulse dial allowed to select
#11 5 Protocol signal display mode
2 USB port number fixed
1 DTMF low frequency compensation
44292401TH Rev.1
Designation Page No.
P.150
P.150
P.151
P.151
P.152
P.152
P.152
P.153
P.153
P.153
P.154
Soft Switch No. Bit No.
8 ECM mode capability
7/6 V.34 fall back counter for V.34 TX
#12 5 Send CTC after 4th PPR
3 Send EOR after lowest speed
2/1 TCF transmission timing after DCS signal
8 MR capability for G3
7/6 Delay time between transaction
5 Super fine printing capability for receiving
#13
3 DTS mode
Send DTC signal if RX DIS signal in manual RX mode
2
(no function on G4)
6 Memory size level to RX
#14
3/2/1 Time between V.34 ANSam signal and FSK DIS signal
8 IPSEL1
#15 7 DCSEL
6 DCLIM
#16 2/1 Fax communication coding method
6 CED frequency
#17 5/4/3 Pause between off hook and CED signal
2/1 Inactivity timer [T5]
6/5 G3 mode training quality level
#18
4/3/2/1 Redefine re-dial attempts counter
8/7/6/5 CNG signal level
#19
4/3/2/1 DTMF high frequency level
—
#20 Reserved
8 NSS signal before DCS
7/6 CNG sending duration after dialing
5 T4 timer
#21
4 VOIP (Voice over IP)
3 DIS signal length
2/1 Increase default T1 timing during calling (Only for TX function)
#22 4/3/2/1 CED signal output level
#23 4/3/2/1 DTMF low frequency level
7/6/5/4/
#24 Re-dial interval
3/2/1
#25 4/3 Flash key time
#26 8/7 Dial tone detection time before disconnected
—
#27 Reserved
8/7/6/5 Time to dial after dial tone on the line
#28
4/3/2/1 CED duration time within calling period
#29 5/4/3/2/1 Time to dial after seize the line when dial tone detection
ADJUSTMENT/SETTING
Designation Page No.
P.154
P.155
P.155
P.155
P.155
P.156
P.156
P.157
P.157
P.157
P.158
P.158
P.158
P.159
P.160
P.160
P.160
P.161
137 /