Smb Ftp; Smb; Bonjour; Ipp - Oki MC160MFP Maintenance Manual

Oki Data CONFIDENTIAL
I.

SMB

Function • Select whether or not to enable SMB.
• If [ENABLE] is selected, SMB is enabled.
Use
• If [DISABLE] is selected, SMB is disabled.
• The default setting is ENABLE.
Setting/
procedure
J. BONJOUR
Function • Select whether or not to use the bonjour setting.
• To use when operating under the bonjour service environment.
Use • If [ENABLE] is selected, Bonjour is enabled.
• If [DISABLE] is selected, Bonjour is disabled.
• The default setting is ENABLE.
Setting/
procedure
K. IPP
Function • Select whether or not to enable IPP.
• If [ENABLE] is selected, IPP is enabled.
Use
• If [DISABLE] is selected, IPP is disabled.
• The default setting is ENABLE.
Setting/
procedure
L. SLP
Function • Select whether or not to enable SLP.
• If [ENABLE] is selected, SLP is enabled.
Use
• If [DISABLE] is selected, SLP is disabled.
• The default setting is ENABLE.
Setting/
procedure
M. SNMP
Function • Select whether or not to enable SNMP.
• If [ENABLE] is selected, SNMP is enabled.
Use
• If [DISABLE] is selected, SNMP is disabled.
• The default setting is ENABLE.
Setting/
procedure
N. SPEED/DUPLEX
Function • Sets the communication speed and method of network.
Use • To set the network communication speed and method.
• The default setting is AUTO.
Setting/
"AUTO" / 10BASE-T FULL / 10BASE-T HALF /
procedure
100BASE-TX FULL / 100BASE-TX HALF
44292401TH Rev.1
DISABLE / "ENABLE"
DISABLE / "ENABLE"
DISABLE / "ENABLE"
DISABLE / "ENABLE"
DISABLE / "ENABLE"
11.4.3 E-MAIL SETTING
12.4.4 E-MAIL SETTING
A. SMTP
Function • Select whether or not to enable SMTP.
• If [ENABLE] is selected, SMTP is enabled.
Use
• If [DISABLE] is selected, SMTP is disabled.
• The default setting is ENABLE.
Setting/
procedure
DISABLE / "ENABLE"
B. SENDER NAME
Function
• This function is used to specify the sender's name.
Use
Setting/ • The default setting is OKI-MC160n.
procedure • Up to 20 characters can be entered for the sender name.
C. E-MAIL ADDRESS
Function • This function is used to specify the e-mail address of the sender.
NOTE
Use
• Please consult customer's network administrator for information about the e-mail
address to use.
• Up to 64 characters can be entered for the sender address.
Setting/
• If customer does not receive e-mail on the copier, enter the e-mail address of the cus-
procedure
tomer's administrator.
D. DEFAULT SUBJECT
Function
• This function is used to specify the default subject line, when sending scan data as an e-
mail attachment.
Use
Setting/ • The default setting is from From OKI-MC160n.
procedure • Up to 20 characters can be entered for the default subject.
E. SMTP SERVER ADDR.
Function • This function is used to enter the IP address or host name of an SMTP server.
NOTE
Use
• Please consult customer's network administrator for information about the IP
address to use.
• Up to 64 characters can be entered for the host name.
Setting/
• The DNS settings must have been specified before specifying the host name for the
procedure
SMTP server.
F. SMTP PORT NO.
Function • This function is used to enter the port number (1 to 65535) for the SMTP server.
NOTE
Use
• Please consult customer's network administrator for information about the port
number to use.
Setting/ • The port number can be set between 1 and 65535.
procedure • Normally, port number 25 is used.
ADJUSTMENT/SETTING
108 /