Table of Contents
Advertisement
Fourth press of
:
e
(Volume answer format preference)
v
v
v
(repeats options)
v
Fifth press of
:
e
(Stair Riser Height Preference – Target gets calculation as close
to Target Riser Height as possible. Max calculation will not exceed
Maximum Riser Height.)
v
(repeats options)
v
Sixth press of
:
e
(Rake Preference – Sets Rake-Wall Stud sizes to Descending or
Ascending order.)
v
(repeats options)
v
Seventh press of
:
e
(Jack Preference – Sets Jack Rafters to Descending or Ascending order)
v
(repeats options)
v
Eighth press of
:
e
(Jack Alignment Preference – Sets Jack Spacing to On-center or Mate)
v
(repeats options)
v
Ninth press of
:
e
(Run/Span Preference – Span is the length of a top plate or twice the length
of the Run)
v
(repeats options)
v
Tenth press of
:
e
(Linear Meters format Preference)
v
(repeats options)
v
Eleventh press of
:
e
(Degrees format Preference)
v
(repeats options)
v
Twelfth press of
:
e
(Order of Entry Preference)
v
(repeats options)
v
VoLUMe UnitS Std. 0.
VoLUMe UnitS CU Yd 0.
VoLUMe UnitS CU Feet 0.
VoLUMe UnitS CU M 0.
VoLUMe UnitS Std. 0.
tarGet riSer hGht. 0.
MaX riSer hGht. 0.
tarGet riSer hGht. 0.
deSCendinG raKe 0.
aSCendinG raKe 0.
deSCendinG raKe 0
deSCendinG JaCK 0.
aSCendinG JaCK 0.
deSCendinG JaCK 0.
JaCK aLiGnMent oC 0.
JaCK aLiGnMent Mate 0.
JaCK aLiGnMent oC 0.
rUn/SPan SettinG rUn 0.
rUn/SPan SettinG SPan 0.
rUn/SPan SettinG rUn 0.
Linear MeterS FiX M 0.000
Linear MeterS aCt. M 0.
Linear MeterS FiX M 0.000
deGreeS — FiXed 0.°
deGreeS — aCtUaL 0.00 °
deGreeS — FiXed 0.00 °
order oF entrY Math 0.
order oF oPer Math 0.
order oF entrY Math 0.
C
M
onstruCtion
15
elliptical arch Function
required entries
Height
Width
Stud On-Center Spacing
• Default value: 16"
Stud Location
• Default setting: Outside the Arch*
optional entries
Base Height
* Stud Position or Location refers to the placement of the studs:
Entering 1 calculates studs located Outside of the Arch
•
Entering 2 calculates studs located Inside of the Arch.
•
Note: All Elliptical Arch solutions are based on 180° arch angles.
Solve for an Elliptical Arch that is 5' high, 15' wide with studs Outside the Arch:
1. Clear Calculator:
OOO
2. Go to Extras function:
CN
(If necessary, continue pressing
3. Start Elliptical Arch function:
e
4. Enter Elliptical Arch Height:
5fe
5. Enter Elliptical Arch Width:
15fe
6. No Base Height:
e
7. Accept 16" Stud On-Center Spacing default value:
e
8. Accept default Stud Position (Outside the Arch) and solve for Elliptical Arch:
e
Center to FoCi Lnth
FoCi to FoCi Lnth
e
StrinG Pt. to Pt. Lnth
e
StrinG LooP Lnth
e
arCh area
e
Center StUd Lnth
e
StUd Pair LenGth Ø1
e
StUd Pair LenGth Ø2
e
StUd Pair LenGth Ø3
e
StUd Pair LenGth Ø4
e
StUd Pair LenGth Ø5
e
StUd Pair LenGth Ø6
e
Crown Molding Function
required entries
Wall Corner Angle
• Default value: 90°
Spring Angle
• Default value: 45°
Solve for Crown Molding with a Corner Angle of 60º and a Spring Angle of 38º:
1. Clear Calculator:
OOO
2. Go to Extras function:
CN
(If necessary, continue pressing
P
eZ
aster
lus
Possible Solutions
Center to Foci Length
Foci to Foci Length
String Point-to-Point Length
String Loop Length
Arch Area
Center Stud Length
Other Stud Lengths
until eLLiPtiCaL arCh displays.)
N
5 Feet 7–1/16 inCh
11 Feet 2–3/16 inCh
15 Feet 0 inCh
26 Feet 2–3/16 inCh
235.61945 SQ Feet
0 Feet 0 inCh
0 Feet 0–15/16 inCh
0 Feet 3–15/16 inCh
0 Feet 9–1/4 inCh
1 Feet 5–13/16 inCh
2 Feet 8–1/2 inCh
5 Feet 0 inCh
Possible Solutions
Miter Angle
Bevel Angle
until CroWn MoLdinG displays.)
N
Advertisement
Table of Contents
