Siemens SIMATIC CPU 1515SP PC2 F User Manual
  1. Manuals
  2. Brands
  3. Siemens Manuals
  4. Control Unit
  5. SIMATIC CPU 1515SP PC2 F
  6. User manual

Siemens SIMATIC CPU 1515SP PC2 F User Manual

Et 200sp open controller
Hide thumbs
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading

Related Manuals for Siemens SIMATIC CPU 1515SP PC2 F

Summary of Contents for Siemens SIMATIC CPU 1515SP PC2 F

  • Page 2 ___________________ Introduction ___________________ Safety information ___________________ SIMATIC Areas of application ___________________ Product overview ET 200SP Open Controller CPU 1515SP PC2 (F/T/TF) ___________________ Application planning ___________________ Installation Operating Instructions ___________________ Wiring ___________________ Commissioning Interrupt, error and system ___________________ messages ___________________ Functions ___________________ Maintenance ___________________...
  • Page 3 Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.

  • Page 4: Table Of Contents

    Table of contents Introduction ............................. 6 Documentation on CPU 1515SP PC2 ..................8 Information about third-party software updates ..............12 Notes on protecting administrator accounts ................12 Safety information ..........................13 Security information ........................ 13 General safety instructions ..................... 14 Notes on use ...........................
  • Page 5 Table of contents Securing cables........................41 Commissioning ............................. 42 Notes on commissioning ......................42 Basic commissioning procedure .................... 43 8.2.1 Requirements ......................... 43 8.2.2 Preparing commissioning ....................... 43 8.2.3 Commissioning procedure ..................... 43 Initial commissioning an open controller ................45 8.3.1 Creating the configuration of the Open Controller ..............
  • Page 6 13.1 CPU 1515SP PC2 ......................... 121 Spare parts/accessories ........................123 14.1 Accessories/spare parts......................123 Appendix............................. 124 Siemens Industry Online Support ..................124 Industry Mall .......................... 124 Troubleshooting ........................125 List of abbreviations ..........................126 Abbreviations ........................126 Glossary ............................. 128 Index..............................

  • Page 7: Introduction

    Introduction Purpose of the documentation These operating instructions supplement the system manual ET 200SP distributed I/O system. Functions that generally relate to the system are described in this manual. The information provided in these operating instructions and in the system/function manuals supports you in commissioning the CPU 1515SP PC2.
  • Page 8 Introduction 1.1 Documentation on CPU 1515SP PC2 Conventions STEP 7: In this documentation, "STEP 7" is used as a synonym for all versions of the configuration and programming software "STEP 7 (TIA Portal)". "CPU1515SP PC2 T" means that the respective section applies only to the "CPU 1515SP PC2 T".

  • Page 9: 1.1 Documentation On Cpu 1515Sp Pc2

    Documentation on CPU 1515SP PC2 The following additional documentation is required to use the CPU 1515SP PC2: ● Operating instructions CPU 1505SP (F/T/TF), CPU 1507S (F) Version 2.5 (http://support.automation.siemens.com/WW/view/en/109740725) ● STEP 7 and WinCC Engineering V15 system manual (https://support.industry.siemens.com/cs/ww/en/view/109755202) ● ET 200SP distributed I/O system manual (http://support.automation.siemens.com/WW/view/en/58649293)
  • Page 10 You need to register once to use the full functionality of "mySupport". You can find "mySupport" in the Internet (https://support.industry.siemens.com/My/ww/en). "mySupport" - Documentation In the Documentation area of "mySupport", you have the possibility to combine complete manuals or parts of them to make your own manual.
  • Page 11 ● Manuals, characteristics, operating manuals, certificates ● Product master data You can find "mySupport" - CAx Data in the Internet (http://support.industry.siemens.com/my/ww/en/CAxOnline). Application examples The application examples support you with various tools and examples for solving your automation tasks. Solutions are shown in interplay with multiple components in the system - separated from the focus in individual products.
  • Page 12 You can find the SIMATIC Automation Tool on the Internet (https://support.industry.siemens.com/cs/ww/en/view/98161300). PRONETA With SIEMENS PRONETA (PROFINET network analysis), you analyze the plant network during commissioning. PRONETA features two core functions: ● The topology overview independently scans PROFINET and all connected components.

  • Page 13: Information About Third-Party Software Updates

    Information about third-party software updates This product contains third-party software. Siemens accepts liability with respect to updates/patches for the third-party software only when these are distributed by Siemens in the context of a Software Update Service contract or officially approved by Siemens.

  • Page 14: Safety Information

    Siemens' products and solutions undergo continuous development to make them more secure. Siemens strongly recommends that product updates are applied as soon as they are available and that the latest product versions are used. Use of product versions that are no longer supported, and failure to apply the latest updates may increase customers' exposure to cyber threats.

  • Page 15: General Safety Instructions

    Seal the cover to protect the CFast card with the operating system of the CPU 1515SP PC2 from unauthorized access. For more information on Industrial Security, refer to the Internet (http://www.siemens.com/industrialsecurity). If you have questions about whether it is permissible to install the device in the planned environment, please contact your service representative.
  • Page 16 Safety information 2.2 General safety instructions ESD guidelines Modules containing electrostatic sensitive devices (ESDs) can be identified by the following label: Strictly follow the guidelines mentioned below when handling modules which are sensitive to ESD: ● Before working with modules with ESD, you need to ensure that you are free of electrostatic charge (e.g.

  • Page 17: Notes On Use

    Safety information 2.3 Notes on use Notes on use WARNING Hazards at an unprotected machine or plant According to the results of a risk analysis, hazards can occur at an unprotected machine. The hazards may lead to personal injury. According to the risk analysis, the risk of injury to persons can be countered with the following measures: •...

  • Page 18: Areas Of Application

    SIMATIC Safety - Configuring and Programming (http://support.automation.siemens.com/WW/view/en/54110126). You can find information on using the CPU 1505SP (F) Software Controller in the associated manual (https://support.industry.siemens.com/cs/ww/en/view/109740725) and in the F-product information (https://support.industry.siemens.com/cs/ww/en/view/109478599). Areas of application of technology CPUs Areas of application Areas of application of T-CPUs are motion control applications such as gearing and camming as well as control of kinematics.

  • Page 19: Product Overview

    Product overview Field of application Article number The article number depends on the pre-installed S7-1500 Software Controller and HMI Runtime. You can find an overview of the article numbers in the section Scope of validity of the documentation (Page 6). View of the module The following figure shows the CPU 1515SP PC2: Figure 4-1...

  • Page 20: Characteristics

    Product overview 4.2 Characteristics Characteristics The CPU 1515SP PC2 is a PC-based automation device in the design of the ET 200SP. It is used for control and visualization purposes. The supplied IPC DiagBase software provides basic diagnostics functions and supports you in handling the BIOS. General characteristics ●...

  • Page 21: Sample Configuration

    Product overview 4.3 Sample configuration Sample configuration Configuration The CPU 1515SP PC2 is mounted on a mounting rail according to EN 60715. A modular system is formed with ET 200SP modules in the central rack. You can also expand the CPU 1515SP PC2 with fail-safe I/O modules.
  • Page 22 PC/Programming device Figure 4-2 Configuration example with the CPU 1515SP PC2 Reference You can find more information about configuring the ET 200AL modules in the system manual ET 200AL distributed I/O system (https://support.industry.siemens.com/cs/ww/en/view/89254965). CPU 1515SP PC2 (F/T/TF) Operating Instructions, 09/2018, A5E42603425-AA...

  • Page 23: Components

    Product overview 4.4 Components Components Components of the CPU 1515SP PC2 The following table provides an overview of the components of the CPU 1515SP PC2: Table 4- 1 Components of the CPU 1515SP PC2 Component Function Figure Mounting rail in accordance The mounting rail is the rack for the with EN 60715 CPU 1515SP PC2.
  • Page 24 Product overview 4.4 Components Component Function Figure BusAdapter The BusAdapter allows free selection of the connection technology for PROFINET IO. The following versions are available for CPU 1515SP PC2: For standard RJ45 connector • ① (BA 2×RJ45) For direct connection of the bus •...

  • Page 25: Operator Controls And Connection Elements

    Product overview 4.5 Operator controls and connection elements Operator controls and connection elements View of the module The following figure shows the operator controls and connection elements of the CPU 1515SP PC2: ① Reference identification labels ② Mounting rail release ③...
  • Page 26 Product overview 4.5 Operator controls and connection elements Slot for CFast card The operating system, Runtime software and project are installed on the supplied SIMATIC CFast card. The CFast card is the only mass storage device of the CPU 1515SP PC2. Note Unauthorized access Seal the cover of the slot to protect the CFast card with the operating system of the...
  • Page 27 Product overview 4.5 Operator controls and connection elements Connector for supply voltage The CPU 1515SP PC2 is equipped with a 2-pin connection terminal for the power supply. The connection plug for the supply voltage is plugged in when the CPU is shipped from the factory.

  • Page 28: Scope Of Delivery

    Product overview 4.6 Scope of delivery Scope of delivery Note The device always comes with the CPU 1515SP PC2 label with article number 6ES7677-2DB40-0AA0, regardless of the order options. The following components are included in the scope of delivery of the CPUs: ●...

  • Page 29: Application Planning

    Application planning Basics Introduction The CPU 1515SP PC2 is open equipment. This means you may only set up the CPU in enclosures, cabinets or electrical equipment rooms and in a dry environment (IP20 degree of protection). The housings, cabinets and electrical operating rooms must guarantee protection against electric shock and spread of fire.

  • Page 30: Unpacking The Device

    ● Check the delivery for correctness and completeness. Please inform your Siemens contact partner should you notice any irregularities. ● Keep the supplied documentation and licenses. They belong to the device and are the proof that you have purchased the software preinstalled on the CFast card.

  • Page 31: Identification Data

    Application planning 5.3 Identification data WARNING Electric shock and fire hazard from damaged device A damaged device can carry dangerous voltage and trigger a fire in the machine or plant. A damaged device has unpredictable properties and states. Death or severe injury could occur. Make sure that the damaged device is not installed and commissioned accidentally.

  • Page 32: Installation Location

    Application planning 5.4 Installation location Installation location Introduction Install the CPU 1515SP PC2 in a suitable housing/control cabinet with sufficient mechanical strength, fire protection and at least IP54 degree of protection according to EN 60529, and take into consideration the ambient conditions for operating the devices. Mounting rail You must ground the mounting rail separately in the control cabinet.
  • Page 33 ● This is followed by BaseUnits BU..B (with dark-colored terminal box). ● The respective corresponding I/O modules can be connected to the BaseUnits. Suitable combinations of BaseUnits and I/O modules can be found in the ET 200SP System Manual (http://support.automation.siemens.com/WW/view/en/84133942). ● The server module completes the installation. Note Install the CPU 1515SP PC2 only with disconnected supply voltage.

  • Page 34: Hardware Configuration

    Application planning 5.5 Hardware configuration Hardware configuration As soon as one of the following rules applies, the maximum configuration has been reached. Maximum mechanical configuration Backplane bus length: Maximum 1 m mounting width (without CPU 1515SP PC2, including server module) Electrical maximum configuration The number of operable I/O modules of a potential group is limited by the ●...

  • Page 35: Installation

    Installation Installing the device Requirements The mounting rail is fitted. Required tools 3 to 3.5 mm screwdriver (only to fix the strain relief and dismantle the BusAdapter) Fixing strain relief Fix the strain relief to the top and bottom of the left-hand side of the CPU 1515SP PC2 with the supplied screws.
  • Page 36 Installation 6.1 Installing the device Uninstalling the CPU 1515SP PC2 The BaseUnits with the I/O modules are located to the right of the CPU 1515SP PC2: 1. Switch off the supply voltage on the CPU. 2. Press the mounting rail release button on the first BaseUnit and, at the same time, move the CPU parallel to the left until it comes off the rest of the module group.

  • Page 37: Wiring

    Rules and regulations for operation Wiring Observe the information contained in the section in the system manual ET 200SP distributed I/O system (http://support.automation.siemens.com/WW/view/en/84133942) and in the function manual Designing interference-free controllers function manual (http://support.automation.siemens.com/WW/view/en/59193566). NOTICE Risk of hazardous system states If you remove and insert I/O devices with the supply voltage switched on, this can result in hazardous system states.

  • Page 38: Terminal And Block Diagram

    Wiring 7.2 Terminal and block diagram Terminal and block diagram Block diagram The following figure shows the block diagram for the CPU 1515SP PC2. ① Switch X1 PN(LAN) PROFINET interface X1 ② Electronics PROFINET interface X1 Port 1 ③ Backplane bus interface PROFINET interface X1 Port 2 ④...

  • Page 39: Electrical Configuration

    Wiring 7.3 Electrical configuration Electrical configuration Non-isolated configuration Note Unlike the ET 200SP distributed I/O system, the CPU 1515SP PC2 can only be operated with a non-isolated configuration. CPU 1515SP PC2 (F/T/TF) Operating Instructions, 09/2018, A5E42603425-AA...
  • Page 40 Wiring 7.3 Electrical configuration The following figure shows the overall configuration of a CPU 1515SP PC2 with power supply from a TN-S system. The power supply supplies the CPU 1515SP PC2 and the load circuit for the 24 V DC modules. For the CPU 1515SP PC2, there is a fixed connection between the ground infeed terminal and the contact springs to the mounting rail.

  • Page 41: Connecting Devices To Networks

    Wiring 7.4 Connecting devices to networks Connecting devices to networks The following options are available for integrating devices into existing or planned system environments and networks. Ethernet You can use the integrated Ethernet interface X2 PN/IE(LAN) (10/100/1000 Mbps) for communication and data exchange with automation devices, for example, SIMATIC S7. Only ASCII characters are permitted in the name of the X2 PN/IE(LAN) interface in the TIA Portal, e.g.

  • Page 42: Securing Cables

    Wiring 7.5 Securing cables Securing cables The strain relief for connecting cables prevents the USB cables and PROFINET connectors detaching from the CPU 1515SP PC2. The strain relief is included in the scope of delivery. WARNING Flying sparks due to loose cables Risk of explosion in hazardous areas.

  • Page 43: Commissioning

    Commissioning Notes on commissioning WARNING Improper commissioning in hazardous areas Device failure or risk of explosion in hazardous areas. • Do not commission the device unless it is fully mounted and connected according to the specifications in the section Wiring (Page 36). •...

  • Page 44: Basic Commissioning Procedure

    Commissioning 8.2 Basic commissioning procedure Basic commissioning procedure Step Execution Section Requirements 8.2.1 (Page 43) Preparing commissioning 8.2.2 (Page 43) Commissioning procedure 8.2.3 (Page 43) 8.2.1 Requirements The following requirements must be met before you commission the Open Controller for the first time: ●...
  • Page 45 Information on users/user groups in Windows A user "Operator" with standard user rights is already created on the Windows system. The user is in a user group "SIEMENS TIA Engineer". This grants the user the rights to use the installed SIMATIC software products.

  • Page 46: Initial Commissioning An Open Controller

    Commissioning 8.3 Initial commissioning an open controller Result ● The Windows 10 IOT Enterprise operating system (64-bit) is installed. ● The "Operator" user is logged on automatically. ● The software controller and WinCC Runtime Advanced, if required, are ready for use. ●...

  • Page 47: Setting The Ip Address

    Commissioning 8.3 Initial commissioning an open controller Creating the configuration To create the configuration in the TIA Portal, follow these steps: 1. Double-click "Add new device" in the project tree. 2. Select "PC systems > SIMATIC S7 Open Controller > ET 200SP Open Controller >". 3.

  • Page 48: Establishing The Hmi Connection

    A network connection is established between the two devices. Reference You can find additional information on configuring an HMI connection in the TIA Portal online help or in the STEP 7 and WinCC Engineering V15 (https://support.industry.siemens.com/cs/ww/en/view/109755202) system manual. 8.3.5 Downloading a project to the target system Key statement To set up your automation system, you need to download the project data you generated offline to the connected devices.

  • Page 49: Transferring License Keys

    Commissioning 8.3 Initial commissioning an open controller 4. Select the interfaces with which you want to establish the online connection to the device. You have the option of showing all compatible devices by selecting the corresponding option and clicking the "Start search" command. Note The first TIA Portal download must be via the "X2"...
  • Page 50 Automation License Manager For additional information on licenses, refer to the manual. You can find the manual on the CPU 1515SP PC2 under Start > All Programs > Siemens Automation > Documentation and on the Internet (http://support.automation.siemens.com/WW/view/en/56956174). You can find more information on the UWF write filter in the section: Protective function for data carriers (Page 57).

  • Page 51: Switching The Open Controller On/Off

    Commissioning 8.3 Initial commissioning an open controller 8.3.7 Switching the Open Controller on/off Requirements Initial commissioning was successfully completed. Switching on the CPU 1515SP PC2 Proceed as follows to switch on the CPU 1515SP PC2: 1. Switch on the power supply of the CPU. The Boot Manager GRUB2DOS starts.

  • Page 52: Interrupt, Error And System Messages

    Interrupt, error and system messages Status and error display LED display The following figure shows the LED displays of the CPU 1515SP PC2. ① RUN/STOP LED (yellow/green LED) ② ERROR LED (red LED) ③ MAINT LED (yellow LED) ④ POWER LED (yellow/green LED) Figure 9-1 LEDs of the CPU 1515SP PC2 CPU 1515SP PC2 (F/T/TF)
  • Page 53 Interrupt, error and system messages 9.1 Status and error display Meaning of the LED displays with active S7-1500 Software Controller The CPU 1515SP PC2 has three LEDs to indicate the current operating state and diagnostics status. The following table shows the meaning of the color combinations of the LED displays in connection with the S7-1500 Software Controller.
  • Page 54 Interrupt, error and system messages 9.1 Status and error display RUN/STOP ERROR LED MAINT LED Meaning Software controller of the CPU is in the operat- ing state STOP. LED lights up LED off LED off yellow The user program is causing an error. LED lights up LED flashes LED flashes...

  • Page 55: Functions

    Functions 10.1 Monitoring functions 10.1.1 Requirements Introduction The CPU 1515SP PC2 has monitoring functions that you can use with the corresponding monitoring software. The following display, monitoring and control functions are available: ● Temperature monitoring ● Monitoring of drives with S.M.A.R.T. functionality ●...

  • Page 56: Temperature Monitoring

    Functions 10.2 Retentive memory NVRAM 10.1.2 Temperature monitoring Three temperature sensors monitor the temperature at different locations of the CPU 1515SP PC2: ● Processor temperature ● Temperature in the vicinity of the RAM ICs/blocks ● Temperature of the basic module If one of the temperature values exceeds the set temperature threshold, the temperature monitoring triggers a temperature error.

  • Page 57: Bios Setup

    Functions 10.3 BIOS setup 10.3 BIOS setup BIOS setup The boot order can be set using the BIOS Setup. Changing the device configuration The device configuration is preset for working with the supplied software. Only change the set values if you have made technical changes to your device. 10.4 Power options A power plan with the name SIMATIC S7 is set as default on the CPU 1515SP PC2.

  • Page 58: Unified Write Filter (Uwf)" Write Filter

    Functions 10.5 "Unified Write Filter (UWF)" write filter 10.5 "Unified Write Filter (UWF)" write filter General information on the UWF write filter The Unified Write Filter (UWF) is a configurable write filter which provides the CFast cards with a write protection. External removable media such as USB sticks and other flash drives that are recognized as removable media by the operating system are not supported.

  • Page 59: Maintenance

    For additional information, please refer to the corresponding product documentation. SIMATIC IPC Service USB flash drive You can use the SIMATIC IPC Service USB flash drives for data backup and restore. You obtain these through the Siemens online ordering system. CPU 1515SP PC2 (F/T/TF) Operating Instructions, 09/2018, A5E42603425-AA...

  • Page 60: Partitions In The Delivery State

    Maintenance 11.2 Partitions in the delivery state 11.2 Partitions in the delivery state Partitioning the CFast card The following partitions are set up on the CFast card by default: Partition Name 30 GB CFast card File system SYSTEM 19.5 GB NTFS DATA 8 GB...

  • Page 61: Restoring The Delivery State

    Maintenance 11.3 Restoring the delivery state 11.3 Restoring the delivery state Introduction The entire image of your operating system and your Runtime software are located on the supplied restore USB stick. You can use the SIMATIC restore menu to restore the delivery state of the CPU 1515SP PC2.
  • Page 62 Maintenance 11.3 Restoring the delivery state Restoring the delivery state of the CPU 1515SP PC2 with restore USB stick Before the restore 1. Connect a monitor and a keyboard to the CPU. 2. Switch off the power supply of the CPU. 3.

  • Page 63: Updating Software

    CPU 1515SP PC2 in the GRUB menu in Windows mode. Information on updating software for the respective product can be found on the Internet (https://support.industry.siemens.com/cs/ww/en). HMI devices During the installation, make sure that you always use the latest drivers for the HMI devices used (SIMATIC Flat Panels).

  • Page 64: Sending The Device To Customer Service

    ● Remove your SD/MMC cards. ● Remove your CFast card. Sending in the device ● Pack the device in its original packaging. ● Enclose identification data (Page 30). ● Send to your Siemens contact partner. CPU 1515SP PC2 (F/T/TF) Operating Instructions, 09/2018, A5E42603425-AA...

  • Page 65: Removing And Inserting The Cfast Card

    Maintenance 11.7 Removing and inserting the CFast card 11.7 Removing and inserting the CFast card Introduction The CPU 1515SP PC2 has a slot for a CFast card. On this card, you will find the operating system, your Runtime software and, after configuration, the project. Seal the cover for the CFast card to protect the system against unauthorized access.

  • Page 66: Recycling And Disposal

    Maintenance 11.8 Recycling and disposal 11.8 Recycling and disposal For ecologically sustainable recycling and disposal of your old device, contact a certificated disposal service for electronic scrap or dispose of the device in accordance with the regulations in your country. CPU 1515SP PC2 (F/T/TF) Operating Instructions, 09/2018, A5E42603425-AA...

  • Page 67: Technical Specifications

    Technical specifications 12.1 Standards and approvals Introduction The general technical specifications cover the following: ● The standards and test values that the CPU 1515SP PC2 complies with and fulfills. ● The test criteria according to which the CPU 1515SP PC2 was tested. Currently valid markings and approvals Note Information for CPU 1515SP PC2...
  • Page 68 Digital Factory Factory Automation DF FA AS SYS P.O. Box 1963 D-92209 Amberg, Germany They are also available for download on the Siemens Industry Online Support (https://support.industry.siemens.com/cs/ww/en/) web pages, keyword "Declaration of Conformity". cULus approval Underwriters Laboratories Inc., complying with ●...
  • Page 69 Technical specifications 12.1 Standards and approvals cULus HAZ. LOC. approval Underwriters Laboratories Inc., complying with ● UL 508 (Industrial Control Equipment) ● CSA C22.2 No. 142 (Process Control Equipment) ● ANSI/ISA 12.12.01 ● CSA C22.2 No. 213 (Hazardous Location) APPROVED for use in Class I, Division 2, Group A, B, C, D Tx;...
  • Page 70 Technical specifications 12.1 Standards and approvals ATEX approval In accordance with EN 60079-15 (Electrical apparatus for potentially explosive atmospheres; Type of protection "n") and EN 60079-0 (Electrical apparatus for potentially explosive gas atmospheres - Part 0: General Requirements) IECEx approval According to IEC 60079-15 (Explosive atmospheres - Part 15: Equipment protection by type of protection "n") and IEC 60079-0 (Explosive atmospheres - Part 0: Equipment - General requirements)
  • Page 71 CPU 1515SP PC2 is not intended for use in residential areas. Using the CPU 1515SP PC2 in residential areas can affect radio and television reception. Reference The certificates for the markings and approvals can be found on the Internet under Service&Support (http://www.siemens.com/automation/service&support). CPU 1515SP PC2 (F/T/TF) Operating Instructions, 09/2018, A5E42603425-AA...

  • Page 72: Electromagnetic Compatibility

    IEC 61000-4-4. ±1 kV (signal lines < 30 m) High-energy single pulse (surge) according to IEC 61000-4-5 External protective circuit required (see function manual Designing interference-free controllers (http://support.automation.siemens.com/WW/view/en/59193566)) ±2 kV (power supply lines) asymmetric coupling • DC with protective elements ±2 kV (signal/data line only >...
  • Page 73 Technical specifications 12.2 Electromagnetic compatibility Sinusoidal disturbance The following table shows the electromagnetic compatibility of the CPU 1515SP PC2 with regard to sinusoidal disturbances. ● RF radiation Table 12- 2 Sinusoidal disturbance variables with RF radiation RF radiation according to IEC 61000-4-3/NAMUR 21 corresponds to degree of severity Electromagnetic RF field, amplitude-modulated...

  • Page 74: Shipping And Storage Conditions

    Technical specifications 12.3 Shipping and storage conditions 12.3 Shipping and storage conditions Introduction The CPU 1515SP PC2 exceeds the requirements of IEC 61131-2 in terms of shipping and storage conditions. The following information applies to modules that are shipped and/or stored in their original packaging.

  • Page 75: Mechanical And Climatic Ambient Conditions

    Technical specifications 12.4 Mechanical and climatic ambient conditions 12.4 Mechanical and climatic ambient conditions Note Restrictions In contrast to the ambient conditions for the ET 200SP distributed I/O system, the following restrictions apply to the CPU 1515SP PC2: • Mechanical ambient conditions: –...
  • Page 76 Technical specifications 12.4 Mechanical and climatic ambient conditions Test of mechanical ambient conditions The table below provides important information with respect to the type and scope of the test of ambient mechanical conditions. Table 12- 8 Test of mechanical ambient conditions Condition tested Test Standard Comment...

  • Page 77: Information On Insulation, Protection Class, Degree Of Protection And Rated Voltage

    Technical specifications 12.5 Information on insulation, protection class, degree of protection and rated voltage 12.5 Information on insulation, protection class, degree of protection and rated voltage Insulation The insulation is designed according to the requirements of EN 61131-2: 2007. Note In the case of modules with 24 V DC (SELV/PELV) supply voltage, galvanic isolations are tested with 707 V DC (type test).

  • Page 78: Use Of The Et 200Sp In Zone 2 Potentially Explosive Atmospheres

    Static value: Creation as functional extra-low voltage with safe electrical isolation in accordance with IEC 60364-4-41 12.6 Use of the ET 200SP in zone 2 potentially explosive atmospheres See product information Use of subassemblies/modules in a Zone 2 Hazardous Area (http://support.automation.siemens.com/WW/view/en/19692172). CPU 1515SP PC2 (F/T/TF) Operating Instructions, 09/2018, A5E42603425-AA...

  • Page 79: Module Data

    Technical specifications of CPU 1515SP PC2 - basic device Technical specifications The following table shows the technical specifications as of 08/2018. You will find a data sheet including daily updated technical specifications on the Internet (https://support.industry.siemens.com/cs/ww/en/pv/6ES7677-2DB40-0AA0/td). Article number 6ES7677-2DB40-0AA0 General information...
  • Page 80 Technical specifications 12.7 Module data Article number 6ES7677-2DB40-0AA0 Memory Type of memory DDR3L Main memory 8 GB RAM CFast memory card SIMATIC memory card required Hardware configuration Integrated power supply Number of DP masters Via CM • Rack 64; CPU + 64 modules + server module (mount- Modules per rack, max.
  • Page 81 Technical specifications 12.7 Module data Article number 6ES7677-2DB40-0AA0 Ambient conditions Ambient temperature during operation 0 °C min. • Up to 60 °C with max. 32 ET 200SP modules and max. • 3x 100 mA USB load; up to 55 °C with max. 64 ET 200SP modules and 2x max.

  • Page 82: Technical Specifications Cpu 1515Sp Pc2

    Technical specifications CPU 1515SP PC2 Technical specifications The following table shows the technical specifications as of 08/2018. You will find a data sheet including daily updated technical specifications on the Internet (https://support.industry.siemens.com/cs/ww/en/pv/6ES7677-2DB42-0GB0/td). Article number 6ES7677-2DB42-0GB0 General information Product type designation...
  • Page 83 Technical specifications 12.7 Module data Article number 6ES7677-2DB42-0GB0 Memory Type of memory DDR3L Main memory 8 GB RAM CFast memory card Yes; 30 GB flash memory SIMATIC memory card required Flash Disk 30 GB Work memory 1 Mbyte integrated (for program) •...
  • Page 84 Technical specifications 12.7 Module data Article number 6ES7677-2DB42-0GB0 1. Interface Interface types Number of ports • integrated switch • Yes; Via BusAdapter BA 2x RJ45 RJ 45 (Ethernet) • 100 Mbit/s – Transmission rate, max. – Industrial Ethernet status LED 2.
  • Page 85 Technical specifications 12.7 Module data Article number 6ES7677-2DB42-0GB0 Ambient temperature during stor- age/transportation -40 °C min. • 70 °C max. • Operating systems Operating systems Windows 10 IoT Enterprise LTSB 2016 (64-bit) Peripherals/Options Peripherals Optionally for additional mass storage SD card •...

  • Page 86: Technical Specifications Of Cpu 1515Sp Pc2 + Hmi 128Pt

    Technical specifications of CPU 1515SP PC2 + HMI 128PT Technical specifications The following table shows the technical specifications as of 08/2018. You will find a data sheet including daily updated technical specifications on the Internet (https://support.industry.siemens.com/cs/ww/en/pv/6ES7677-2DB42-0GK0/td). Article number 6ES7677-2DB42-0GK0 General information...
  • Page 87 Technical specifications 12.7 Module data Article number 6ES7677-2DB42-0GK0 Memory Type of memory DDR3L Main memory 8 GB RAM CFast memory card Yes; 30 GB flash memory SIMATIC memory card required Flash Disk 30 GB Work memory 1 Mbyte integrated (for program) •...
  • Page 88 Technical specifications 12.7 Module data Article number 6ES7677-2DB42-0GK0 1. Interface Interface types Number of ports • integrated switch • Yes; Via BusAdapter BA 2x RJ45 RJ 45 (Ethernet) • 100 Mbit/s – Transmission rate, max. – Industrial Ethernet status LED 2.
  • Page 89 Technical specifications 12.7 Module data Article number 6ES7677-2DB42-0GK0 Operating systems Operating systems Windows 10 IoT Enterprise LTSB 2016 (64-bit) Peripherals/Options Peripherals Optionally for additional mass storage SD card • Dimensions Width 160 mm Height 117 mm Depth 75 mm Weights Weight, approx.

  • Page 90: Technical Specifications Of Cpu 1515Sp Pc2 + Hmi 512Pt

    Technical specifications of CPU 1515SP PC2 + HMI 512PT Technical specifications The following table shows the technical specifications as of 08/2018. You will find a data sheet including daily updated technical specifications on the Internet (https://support.industry.siemens.com/cs/ww/en/pv/6ES7677-2DB42-0GL0/td). Article number 6ES7677-2DB42-0GL0 General information...
  • Page 91 Technical specifications 12.7 Module data Article number 6ES7677-2DB42-0GL0 Memory Type of memory DDR3L Main memory 8 GB RAM CFast memory card Yes; 30 GB flash memory SIMATIC memory card required Flash Disk 30 GB Work memory 1 Mbyte integrated (for program) •...
  • Page 92 Technical specifications 12.7 Module data Article number 6ES7677-2DB42-0GL0 1. Interface Interface types Number of ports • integrated switch • Yes; Via BusAdapter BA 2x RJ45 RJ 45 (Ethernet) • 100 Mbit/s – Transmission rate, max. – Industrial Ethernet status LED 2.
  • Page 93 Technical specifications 12.7 Module data Article number 6ES7677-2DB42-0GL0 Operating systems Operating systems Windows 10 IoT Enterprise LTSB 2016 (64-bit) Peripherals/Options Peripherals Optionally for additional mass storage SD card • Dimensions Width 160 mm Height 117 mm Depth 75 mm Weights Weight, approx.

  • Page 94: Technical Specifications Of Cpu 1515Sp Pc2 + Hmi 2048Pt

    Technical specifications of CPU 1515SP PC2 + HMI 2048PT Technical specifications The following table shows the technical specifications as of 08/2018. You will find a data sheet including daily updated technical specifications on the Internet (https://support.industry.siemens.com/cs/ww/en/pv/6ES7677-2DB42-0GM0/td). Article number 6ES7677-2DB42-0GM0 General information...
  • Page 95 Technical specifications 12.7 Module data Article number 6ES7677-2DB42-0GM0 Memory Type of memory DDR3L Main memory 8 GB RAM CFast memory card Yes; 30 GB flash memory SIMATIC memory card required Flash Disk 30 GB Work memory 1 Mbyte integrated (for program) •...
  • Page 96 Technical specifications 12.7 Module data Article number 6ES7677-2DB42-0GM0 1. Interface Interface types Number of ports • integrated switch • Yes; Via BusAdapter BA 2x RJ45 RJ 45 (Ethernet) • 100 Mbit/s – Transmission rate, max. – Industrial Ethernet status LED 2.
  • Page 97 Technical specifications 12.7 Module data Article number 6ES7677-2DB42-0GM0 Operating systems Operating systems Windows 10 IoT Enterprise LTSB 2016 (64-bit) Peripherals/Options Peripherals Optionally for additional mass storage SD card • Dimensions Width 160 mm Height 117 mm Depth 75 mm Weights Weight, approx.

  • Page 98: Technical Specifications Of Cpu 1515Sp Pc2 F

    Technical specifications of CPU 1515SP PC2 F Technical specifications The following table shows the technical specifications as of 08/2018. You will find a data sheet including daily updated technical specifications on the Internet (https://support.industry.siemens.com/cs/ww/en/pv/6ES7677-2SB42-0GB0/td). Article number 6ES7677-2SB42-0GB0 General information Product type designation...
  • Page 99 Technical specifications 12.7 Module data Article number 6ES7677-2SB42-0GB0 Memory Type of memory DDR3L Main memory 8 GB RAM CFast memory card Yes; 30 GB flash memory SIMATIC memory card required Flash Disk 30 GB Work memory 1.5 Mbyte integrated (for program) •...
  • Page 100 Technical specifications 12.7 Module data Article number 6ES7677-2SB42-0GB0 1. Interface Interface types Number of ports • integrated switch • Yes; Via BusAdapter BA 2x RJ45 RJ 45 (Ethernet) • 100 Mbit/s – Transmission rate, max. – Industrial Ethernet status LED 2.
  • Page 101 Technical specifications 12.7 Module data Article number 6ES7677-2SB42-0GB0 Operating systems Operating systems Windows 10 IoT Enterprise LTSB 2016 (64-bit) Peripherals/Options Peripherals Optionally for additional mass storage SD card • Dimensions Width 160 mm Height 117 mm Depth 75 mm Weights Weight, approx.

  • Page 102: Technical Specifications Of Cpu 1515Sp Pc2 F + Hmi 128Pt

    Technical specifications of CPU 1515SP PC2 F + HMI 128PT Technical specifications The following table shows the technical specifications as of 08/2018. You will find a data sheet including daily updated technical specifications on the Internet (https://support.industry.siemens.com/cs/ww/en/pv/6ES7677-2SB42-0GK0/td). Article number 6ES7677-2SB42-0GK0 General information...
  • Page 103 Technical specifications 12.7 Module data Article number 6ES7677-2SB42-0GK0 Memory Type of memory DDR3L Main memory 8 GB RAM CFast memory card Yes; 30 GB flash memory SIMATIC memory card required Flash Disk 30 GB Work memory 1.5 Mbyte integrated (for program) •...
  • Page 104 Technical specifications 12.7 Module data Article number 6ES7677-2SB42-0GK0 1. Interface Interface types Number of ports • integrated switch • Yes; Via BusAdapter BA 2x RJ45 RJ 45 (Ethernet) • 100 Mbit/s – Transmission rate, max. – Industrial Ethernet status LED 2.
  • Page 105 Technical specifications 12.7 Module data Article number 6ES7677-2SB42-0GK0 Operating systems Operating systems Windows 10 IoT Enterprise LTSB 2016 (64-bit) Peripherals/Options Peripherals Optionally for additional mass storage SD card • Dimensions Width 160 mm Height 117 mm Depth 75 mm Weights Weight, approx.

  • Page 106: Technical Specifications Of Cpu 1515Sp Pc2 F + Hmi 512Pt

    Technical specifications of CPU 1515SP PC2 F + HMI 512PT Technical specifications The following table shows the technical specifications as of 08/2018. You will find a data sheet including daily updated technical specifications on the Internet (https://support.industry.siemens.com/cs/ww/en/pv/6ES7677-2SB42-0GL0/td). Article number 6ES7677-2SB42-0GL0 General information...
  • Page 107 Technical specifications 12.7 Module data Article number 6ES7677-2SB42-0GL0 Memory Type of memory DDR3L Main memory 8 GB RAM CFast memory card Yes; 30 GB flash memory SIMATIC memory card required Flash Disk 30 GB Work memory 1.5 Mbyte integrated (for program) •...
  • Page 108 Technical specifications 12.7 Module data Article number 6ES7677-2SB42-0GL0 1. Interface Interface types Number of ports • integrated switch • Yes; Via BusAdapter BA 2x RJ45 RJ 45 (Ethernet) • 100 Mbit/s – Transmission rate, max. – Industrial Ethernet status LED 2.
  • Page 109 Technical specifications 12.7 Module data Article number 6ES7677-2SB42-0GL0 Operating systems Operating systems Windows 10 IoT Enterprise LTSB 2016 (64-bit) Peripherals/Options Peripherals Optionally for additional mass storage SD card • Dimensions Width 160 mm Height 117 mm Depth 75 mm Weights Weight, approx.

  • Page 110: Technical Specifications Of Cpu 1515Sp Pc2 F + Hmi 2018Pt

    Technical specifications of CPU 1515SP PC2 F + HMI 2018PT Technical specifications The following table shows the technical specifications as of 08/2018. You will find a data sheet including daily updated technical specifications on the Internet (https://support.industry.siemens.com/cs/ww/en/pv/6ES7677-2SB42-0GM0/td). Article number 6ES7677-2SB42-0GM0 General information...
  • Page 111 Technical specifications 12.7 Module data Article number 6ES7677-2SB42-0GM0 Memory Type of memory DDR3L Main memory 8 GB RAM CFast memory card Yes; 30 GB flash memory SIMATIC memory card required Flash Disk 30 GB Work memory 1.5 Mbyte integrated (for program) •...
  • Page 112 Technical specifications 12.7 Module data Article number 6ES7677-2SB42-0GM0 1. Interface Interface types Number of ports • integrated switch • Yes; Via BusAdapter BA 2x RJ45 RJ 45 (Ethernet) • 100 Mbit/s – Transmission rate, max. – Industrial Ethernet status LED 2.
  • Page 113 Technical specifications 12.7 Module data Article number 6ES7677-2SB42-0GM0 Operating systems Operating systems Windows 10 IoT Enterprise LTSB 2016 (64-bit) Peripherals/Options Peripherals Optionally for additional mass storage SD card • Dimensions Width 160 mm Height 117 mm Depth 75 mm Weights Weight, approx.

  • Page 114: Technical Specifications Of Cpu 1515Sp Pc2 T

    Technical specifications of CPU 1515SP PC2 T Technical specifications The following table shows the technical specifications as of 08/2018. You will find a data sheet including daily updated technical specifications on the Internet (https://support.industry.siemens.com/cs/ww/en/pv/6ES7677-2VB42-0GB0/td). Article number 6ES7677-2VB42-0GB0 General information Product type designation...
  • Page 115 Technical specifications 12.7 Module data Article number 6ES7677-2VB42-0GB0 Memory Type of memory DDR3L Main memory 8 GB RAM CFast memory card Yes; 30 GB flash memory SIMATIC memory card required Flash Disk 30 GB Work memory 1.5 Mbyte integrated (for program) •...
  • Page 116 Technical specifications 12.7 Module data Article number 6ES7677-2VB42-0GB0 1. Interface Interface types Number of ports • integrated switch • Yes; Via BusAdapter BA 2x RJ45 RJ 45 (Ethernet) • 100 Mbit/s – Transmission rate, max. – Industrial Ethernet status LED 2.
  • Page 117 Technical specifications 12.7 Module data Article number 6ES7677-2VB42-0GB0 Operating systems Operating systems Windows 10 IoT Enterprise LTSB 2016 (64-bit) Peripherals/Options Peripherals Optionally for additional mass storage SD card • Dimensions Width 160 mm Height 117 mm Depth 75 mm Weights Weight, approx.

  • Page 118: Technical Specifications Of Cpu 1515Sp Pc2 Tf

    Technical specifications of CPU 1515SP PC2 TF Technical specifications The following table shows the technical specifications as of 08/2018. You will find a data sheet including daily updated technical specifications on the Internet (https://support.industry.siemens.com/cs/ww/en/pv/6ES7677-2WB42-0GB0/td). Article number 6ES7677-2WB42-0GB0 General information Product type designation...
  • Page 119 Technical specifications 12.7 Module data Article number 6ES7677-2WB42-0GB0 Memory Type of memory DDR3L Main memory 8 GB RAM CFast memory card Yes; 30 GB flash memory SIMATIC memory card required Flash Disk 30 GB Work memory 1.5 Mbyte integrated (for program) •...
  • Page 120 Technical specifications 12.7 Module data Article number 6ES7677-2WB42-0GB0 1. Interface Interface types Number of ports • integrated switch • Yes; Via BusAdapter BA 2x RJ45 RJ 45 (Ethernet) • 100 Mbit/s – Transmission rate, max. – Industrial Ethernet status LED 2.

  • Page 121: S7-1500 Software Controller Cpu 1505Sp (F/T/Tf)

    The CPU 1505SP (F/T/TF) is a PC-based controller of the SIMATIC S7-1500 Software Controller family. You can find additional information about the CPU 1505SP (F/T/TF) in the relevant manual (https://support.industry.siemens.com/cs/ww/en/view/109740725). For the CPU 1505SP (F/T/TF), please also note the information in the F product information (https://support.industry.siemens.com/cs/ww/en/view/109478599).

  • Page 122: Dimension Drawings

    Dimension drawings 13.1 CPU 1515SP PC2 This section contains a dimension drawing of the module mounted on a mounting rail. Always observe the specified dimensions for installation in cabinets. Dimension drawings of the CPU 1515SP PC2 Figure 13-1 Dimension drawing CPU 1515SP PC2, front view CPU 1515SP PC2 (F/T/TF) Operating Instructions, 09/2018, A5E42603425-AA...
  • Page 123 Dimension drawings 13.1 CPU 1515SP PC2 Figure 13-2 Dimension drawing CPU 1515SP PC2, side view CPU 1515SP PC2 (F/T/TF) Operating Instructions, 09/2018, A5E42603425-AA...

  • Page 124: Spare Parts/Accessories

    Length: 430 mm • 6ES5710-8MA31 Length: 830 mm • 6ES5710-8MA41 Length: 2000 mm • Online catalog Additional article numbers can be found on the Internet in the online catalog and online ordering system (http://www.siemens.com/automation/mall). CPU 1515SP PC2 (F/T/TF) Operating Instructions, 09/2018, A5E42603425-AA...

  • Page 125: Appendix

    This information is provided by the Siemens Industry Online Support in the Internet (http://www.siemens.com/automation/service&support). Industry Mall The Industry Mall is the catalog and order system of Siemens AG for automation and drive solutions on the basis of Totally Integrated Automation (TIA) and Totally Integrated Power (TIP).

  • Page 126: Troubleshooting

    Appendix A.3 Troubleshooting Troubleshooting Problem Possible cause Remedy CPU 1515SP PC2 does not work. CPU 1515SP PC2 is not supplied Check the power supply. with power. Time and/or date of the CPU 1515SP PC2 CPU 1515SP PC2 was not con- Check the settings in Windows.

  • Page 127: List Of Abbreviations

    List of abbreviations Abbreviations Abbreviation Term Meaning Alternating current Alternating current Automation License Manager Tool for managing license keys in STEP 7 BIOS Basic Input Output System Basic Input Output System. A set of important software rou- tines used after the startup of the CPU to load the operating system and to provide the routines for data exchange between hardware components.
  • Page 128 List of abbreviations B.1 Abbreviations Abbreviation Term Meaning Programming device Compact programming device which meets the special re- quirements of industry. The PG is fully equipped for program- ming SIMATIC PLCs. Power supply Power supply Power Tags Process tags; tags enable data exchange between the com- ponents of an automation process, for example, between the HMI device and the controller.

  • Page 129: Glossary

    Glossary Cold restart A startup procedure commencing when the CPU is switched on. Upon a cold restart, the system typically performs some basic hardware checks and then loads the operating system from the hard disk into the work memory. Controller Integrated hardware and software controlling the operation of a specific internal or I/O device (e.g.
  • Page 130 License key The license key is the electronic license stamp of a license. Siemens AG provides a license key for software that is protected by licensing laws.
  • Page 131 Glossary SATA Serial ATA. An interface for hard disk drives and optical drives with serial data transfer. SETUP (BIOS setup) A program used to determine information on the device configuration. The device configuration of the CPU 1515SP PC2 is preset. Changes must be made whenever a memory expansion, new modules or drives are to be activated.

  • Page 132: Index

    Index Characteristics Control cabinet, 19 Degree of protection, 19 General, 19 Interfaces, 19 Alternating current, 126 Power supply, 19 Accessories, 123 Pre-installations, 19 Address space, 33 Climatic ambient conditions, 75 Automation License Manager, 126 Certificate of Authenticity, 126 Alternating current AC, 126 Certificate of License, 126 Ambient conditions...
  • Page 133 Index Gigabit Ethernet GbE, 126 Data GRand Unified Bootloader Backup, 58 GRUB/GRUB2DOS, 126 Restoring, 58 GRUB/GRUB2DOS Data backup, 58 GRand Unified Bootloader, 126 SIMATIC IPC Image & Partition Creator, 58, 58 Direct current, 126 Degree of protection, 76 Dimension drawing CPU 1515SP PC2, 121 Human Machine Interface, 126 Direct current...
  • Page 134 Index Power, 52 Multi Media Card RUN/STOP, 52 MMC, 126 License Certificate of License, 49 Software, 48 License key Network connection Backup, 49 HMI, 47 Restore, 49 Networks transfer, 48 Ethernet, 40 Light Emitting Diode PROFIBUS, 40 LED, 126 PROFINET, 40 Link Layer Discovery Protocol New Technology File System LLDP, 126...
  • Page 135 Index Programming device, 127 Safety Extra Low Voltage SELV, 127 PROFINET, 126 Safety information, 14 Power options ESD guidelines, 15 Functions, 56 Repairs, 14 Power supply Safe operation of a plant, 14 PS, 127 Sample configuration, 20 Power Tags Configuration, 20 PT, 127 Scope, 7 Procedure...
  • Page 136 Index Underwriters Laboratories Inc., 127 Underwriters Laboratories Inc. UL, 127 Unified Write Filter UWF, 127 Universal Serial Bus USB, 127 Updates for installing Windows, 63 Universal Serial Bus, 127 in industrial environments, 70 in mixed areas, 70 in residential areas, 70 Unified Write Filter, 127 Windows Installing updates, 63...

This manual is also suitable for:

Simatic cpu 1515sp pc2 tSimatic cpu 1515sp pc2 tf

Table of Contents