Subscribe to Our Youtube Channel
Related Manuals for JUMO dTRON 304
Summary of Contents for JUMO dTRON 304
- Page 1 JUMO dTRON 316 JUMO dTRON 308 JUMO dTRON 308 JUMO dTRON 304 J dTRON 304 J dTRON 308 J dTRON 316 Compact Controller with program function B 70.3041.1 Operating Instructions 06.05...
-
Page 3: Table Of Contents
Contents Preface ............... 3 Scope of delivery ..............3 Identifying the instrument version ....4 Mounting ............5 Preparation ................5 Fitting in position, Type 703042/43/44 ........5 Fitting in position, Type 703041 ..........5 Electrical connection ........6 Connection diagram for Type 703041 ........6 Connection diagram for Type 703042/43/44 ...... -
Page 4: Preface
The factory settings for the instrument as delivered are shown on a rastering gray background. The complete configuration options can be found in the comprehensive Operating Manual B 70.3041.0 on the CD, or can be downloaded from http://www.jumo.net Scope of delivery - 1 controller - seal - mounting brackets... -
Page 5: Identifying The Instrument Version
1 analog input, 2 relay outputs and 2 binary inputs or 2 logic outputs 703042 JUMO dTRON 308, 48 mm x 96 mm format (portrait format) incl. 1 analog and 2 binary inputs, 2 relays and 2 logic outputs 703043 JUMO dTRON 308, 96 mm x 48 mm format (landscape format) incl. -
Page 6: Mounting
3 Mounting Mounting Preparation Type dTRON Panel cut-out +0.6 +0.6 703041 316, in 48 mm x 48 mm format x 45 +0.8 +0.8 703042/43 308, in 48 mm x 96 mm format x 92 (portrait)/(landscape) +0.8 +0.8 703044 304, in 96 mm x 96 mm format x 92 Fitting in position, Type 703042/43/44 h Fit the seal that is supplied onto the instrument... -
Page 7: Electrical Connection
4 Electrical connection Electrical connection Connection diagram for Type 703041... -
Page 8: Connection Diagram For Type 703042/43/44
4 Electrical connection Connection diagram for Type 703042/43/44... -
Page 9: Displays And Keys
5 Displays and keys Displays and keys EXIT (1) 7-segment display (factory setting: process value) four-digit, red, decimal place is configurable (automatic adjustment on display overflow) (2) Active setpoint (factory setting: SP1) SP1, SP2, SP3, SP4 (SP=setpoint); green; (3) 7-segment display (factory setting: setpoint) four-digit, green, decimal place is configurable;... -
Page 10: Operation
6 Operation Operation Level concept The diagram below shows the three instrument levels. Time-out If no key is pressed for 30 sec, the instrument returns to normal display. -
Page 11: Level Inhibit
6 Operation Level inhibit The access to the individual levels can be inhibited by entering a code number. h Press simultaneously for >5 sec to enter the code. Code Operator level Parameter level Configuration level enabled enabled enabled enabled enabled inhibited enabled inhibited... -
Page 12: Entering Times
6 Operation Entering times When entering times (e.g. time of timer), the time unit is shown in addition. Select Alter parameter parameter I I I I I I I I I I I I I The highest time unit of the display is shown for the unit. For example, if “h”... -
Page 13: Operation Of The Fixed-Setpoint Controller
6 Operation Operation of the fixed-setpoint controller The fixed-setpoint controller will only function if - the fixed-setpoint controller function has been configured ( Fnct = 0) Normal display Manual mode h Alter the present setpoint The controller output appears in the with lower display. -
Page 14: Operation Of The Program Controller
6 Operation Operation of the program controller The program controller will only function if - the program controller function has been configured ( Fnct = 1 ...4) - the program setpoints (SPP1 ... SPP8) and segment times (tP 1 ... tP 8) have been entered Normal display Program is running (the symbol for ramp appears) -
Page 15: Operator Level "Opr
7 Operator level “OPr” Operator level “OPr” Process data ProC Symbol Meaning SP 1 Setpoint 1 (editable) SP 2 Setpoint 2 (editable) SP 3 Setpoint 3 (editable) SP 4 Setpoint 4 (editable) Ramp setpoint (only if configured) InP1 Measurement of analog input 1 InP2 Measurement of analog input 2 (only if available) Calculated result of math formula 1 (only if available) -
Page 16: Parameter Level "Para
8 Parameter level “PArA” Parameter level “PArA” Two parameter sets, PAr1 und PAr2, can be stored. Parameter Symbol Value range Factory setting Proportional band 1 Pb 1 0 ... 9999 °C/°F 0 °C/°F Proportional band 2 Pb 2 0 ... 9999 °C/°F 0 °C/°F Derivative time 0 ... -
Page 17: Configuration Level "Conf
9 Configuration level “ConF” Configuration level “ConF” Depending on the equipment level of the instrument, individual parameters or groups of parameters are switched out of display. Analog selector With some parameters, you can choose from a series of analog signals. The list below gives you an overview of the selection options. -
Page 18: Controller "Cntr
9 Configuration level “ConF” Linearization 0 Linear 10 Thermocouple type U 1 Pt100 11 Thermocouple type L 2 Pt500 12 Thermocouple type K 3 Pt1000 13 Thermocouple type S 4 KTY11-6 14 Thermocouple type R 5 Thermocouple type C 15 Thermocouple type B 6 Thermocouple type D 16 Thermocouple type N 7 Thermocouple type E... -
Page 19: Outputs "Outp
9 Configuration level “ConF” Outputs “OutP” Numbering of the outputs Standard: Relay 1 = output 1; relay 2 = output 2; logic output 1 = output 3; logic output 2 = output 4 Slot Plug-in board with Plug-in board with Plug-in board with 1 analog output 1 binary output... -
Page 20: Display "Disp
9 Configuration level “ConF” r Binary outputs OutL r Output 1 — 10 Out1 ... Out0 r Function 0 no function 16 Limit comparator 4 1 Controller output 1 17 Control contact 1 2 Controller output 2 18 Control contact 2 3 - not used 19 Control contact 3 4 - not used... -
Page 21: Autotuning
10 Autotuning 10 Autotuning The autotuning facility can be used to automatically adapt the controller parameters to the process. The autotuning function determines the controller parameters for a PID controller or, if dt=0 is set, for a PI controller in a closed control loop. h Start with (press simultaneously for >2 sec) “tUnE”... -
Page 22: Alarms
11 Alarms 11 Alarms Display Cause Clear faults check/rectify/replace -1999 Underrange for the value being Is the medium to be (blinking!) displayed. measured within the range (too hot - too cold?) 9999 Overrange for the value being (blinking!) Check probe for probe displayed. - Page 23 11 Alarms...
- Page 24 JUMO GmbH & Co. KG Street adress: Moltkestraße 13 - 31 36039 Fulda, Germany Delivery address: Mackenrodtstraße 14 36039 Fulda, Germany Postal address: 36035 Fulda, Germany Phone: +49 661 6003-0 Fax: +49 661 6003-607 e-mail: mail@jumo.net Internet: www.jumo.net JUMO Instrument Co. Ltd.
Need help?
Do you have a question about the dTRON 304 and is the answer not in the manual?
Questions and answers