Verlinde Eurolift Owner's Manual

Verlinde Eurolift Owner's Manual

Electric belt hoist hb

Advertisement

EUROLIFT
Owner's Manual
ELECTRIC BELT HOIST HB
VERLINDE S.A. reserves the right to alter or amend the above information without notice
KHVOMSXBGB2006/08

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Eurolift and is the answer not in the manual?

Questions and answers

Summary of Contents for Verlinde Eurolift

  • Page 1 EUROLIFT Owner’s Manual ELECTRIC BELT HOIST HB VERLINDE S.A. reserves the right to alter or amend the above information without notice KHVOMSXBGB2006/08...
  • Page 2 1 - EC Declaration of conformity As defined by the EC directive relating to machinery 98/37/EEC. Annex II A VERNOUILLET France Herewith, we declare that the product : Complies with the following provisions applying to it: Machinery directive 98/37/EEC. Directive 2006/95CEE. "EMC"...
  • Page 3 If the customer wants to make a modification, he should refer to the manufacturer. • Please only use our original spare parts, for safety and to benefit from the manufacturer’s guarantee. Page 2 VERLINDE S.A. reserves the right to alter or amend the above information without notice KHHOMSBHGB2006/08...
  • Page 4: Table Of Contents

    MONITORING THE BELT ................... 21 LOAD LIMITER DESCRIPTION WITH DRAWING ..........22 LUBRICATION ....................23 OPERATING INCIDENTS ................23 SPARE PARTS ....................24 Page 3 VERLINDE S.A. reserves the right to alter or amend the above information without notice KHHOMSBHGB2006/08...
  • Page 5: Construction And Operating Principle

    - Steel construction 4-wheel crab, electric drive, 2-speed brake motor. - Adjustable sides to allow installation of monorail on different support beam widths. 1.2 Operation Refer to the diagram : Page 4 VERLINDE S.A. reserves the right to alter or amend the above information without notice KHHOMSBHGB2006/08...
  • Page 6 5 and finally drum 1 rises into direct contact with the axis of the reduction gear. Page 5 VERLINDE S.A. reserves the right to alter or amend the above information without notice KHHOMSBHGB2006/08...
  • Page 7: Travelling Machinery (Variation Speed)

    Any other kind of use (e.g. hoisting motion) is forbidden. Machinery is suitable for indoor use. Please note possible restrictions for special environments (e.g. galvanization plants). Page 6 VERLINDE S.A. reserves the right to alter or amend the above information without notice KHHOMSBHGB2006/08...
  • Page 8 The parameters of the frequency variator are factory-pre-set through the parameter adjustment buttons (4). All connections to the frequency variator pass through connector (1). Page 7 VERLINDE S.A. reserves the right to alter or amend the above information without notice KHHOMSBHGB2006/08...
  • Page 9: Travelling Machinery (Two Speed)

    Machinery is suitable for both indoor and outdoor use. Please note possible restrictions for special environments (e.g. galvanization plants). Page 8 VERLINDE S.A. reserves the right to alter or amend the above information without notice KHHOMSBHGB2006/08...
  • Page 10: Recommendations For Use

    (see § 5-4) • Temperature of use: - Minimum: - 10° C - Maximum: + 40° C Page 9 VERLINDE S.A. reserves the right to alter or amend the above information without notice KHHOMSBHGB2006/08...
  • Page 11: Important Points To Be Checked Before Start Up And After Doing Any Work

    No mechanical or electrical modifications or adaptations may be made without the factory’s agreement, otherwise the guarantee will no longer be valid. Page 10 VERLINDE S.A. reserves the right to alter or amend the above information without notice KHHOMSBHGB2006/08...
  • Page 12: Documentation And Certificates

    • Factory inspection certificate (including belt and hook) • Connection diagram • Service and maintenance instructions • CE declaration of conformity or declaration of incorporation. Page 11 VERLINDE S.A. reserves the right to alter or amend the above information without notice KHHOMSBHGB2006/08...
  • Page 13: Start Up

    Support Rings and washers for Rings and washers for Tie rod beam dimension X mm dimension Z mm length Y width 8 mm Page 12 VERLINDE S.A. reserves the right to alter or amend the above information without notice KHHOMSBHGB2006/08...
  • Page 14: Connection To The Network

    The power supply must be provided through cables with a sufficiently large cross- section and must be protected by fuses (see table below for calibration). An isolating switch must be installed close to the hoist. Page 13 VERLINDE S.A. reserves the right to alter or amend the above information without notice KHHOMSBHGB2006/08...
  • Page 15: Mounting Position Of The Travelling Machinery

    100°C. If the temperature rise is too high the motor may run faulty, the cooling does not function correctly or the motor is overloaded. The reason must be identified and corrected by an authorized serviceman. Page 14 VERLINDE S.A. reserves the right to alter or amend the above information without notice KHHOMSBHGB2006/08...
  • Page 16: Adjustment Of Top And Bottom Limit Switches

    Rotate cam in the direction of the arrow M until contact is triggered. Page 15 VERLINDE S.A. reserves the right to alter or amend the above information without notice KHHOMSBHGB2006/08...
  • Page 17 Belt Hoist ADJUSTING THE TOP LIMIT SWITCH Bottom limit switch control cam Top limit switch control cam Bottom limit switch Top limit switch Page 16 VERLINDE S.A. reserves the right to alter or amend the above information without notice KHHOMSBHGB2006/08...
  • Page 18: Handling And Installing The Belt Hoist

    The hoist is delivered with four handling flats mark 3. Fasten the slings attached to your handling equipment into the four holes in these flats mark 3. Page 17 VERLINDE S.A. reserves the right to alter or amend the above information without notice KHHOMSBHGB2006/08...
  • Page 19: Installing The Hoist On Its Support Beam Rail

    EUROLIFT OWNER’S MANUAL Belt Hoist 7 INSTALLING THE HOIST ON ITS SUPPORT BEAM RAIL Lifting sling 2 Lifting sling 1 Page 18 VERLINDE S.A. reserves the right to alter or amend the above information without notice KHHOMSBHGB2006/08...
  • Page 20: Pulley Block Hook And Belt

    M 8 screws, start up at low speed to wind on the entire length of the belt. The drum must be full. Page 19 VERLINDE S.A. reserves the right to alter or amend the above information without notice KHHOMSBHGB2006/08...
  • Page 21 Wrong Wrong Make sure that the belt is correctly centered in the pulleys and check the position of the fixed point locking wedge. Page 20 VERLINDE S.A. reserves the right to alter or amend the above information without notice KHHOMSBHGB2006/08...
  • Page 22: Monitoring The Belt

    When fluffing starts to occur, monitor the condition of the belt regularly and replace it as soon as the fluffy width exceeds 3 mm. Page 21 VERLINDE S.A. reserves the right to alter or amend the above information without notice KHHOMSBHGB2006/08...
  • Page 23: Load Limiter Description With Drawing

    The user must not modify the setting of the limiter. Put the protective cover back in place after doing any work. Page 22 VERLINDE S.A. reserves the right to alter or amend the above information without notice KHHOMSBHGB2006/08...
  • Page 24: Lubrication

    - Inspection by a station approved by VERLINDE: in particular, replace dirty pulleys. Please contact our nearest After Sales station for any incident. Page 23 VERLINDE S.A. reserves the right to alter or amend the above information without notice KHHOMSBHGB2006/08...
  • Page 25: Spare Parts

    Set of bearings BELT (length to be specified) 7303436 T Type Po 35 7304429 X Type Dy 35 7541514 Y LIFTING LIMIT SWITCH R 325/3 Page 24 VERLINDE S.A. reserves the right to alter or amend the above information without notice KHHOMSBHGB2006/08...
  • Page 26 Set of two tie rods for. 190 - 220 wide I-beams 15002517 Set of two tie rods for. 240 wide I-beams 7359010 Z Brake assembly (see maintenance instructions) 7359011 A Disk brake Page 25 VERLINDE S.A. reserves the right to alter or amend the above information without notice KHHOMSBHGB2006/08...
  • Page 27 4/1 oscillating assembly 11303505 Equipped belt return pulley 11202505 FIXED POINT ASSEMBLY 11202506 Stainless steel fixed point assembly 12133505 XB 2 belt attachment wedge Page 26 VERLINDE S.A. reserves the right to alter or amend the above information without notice KHHOMSBHGB2006/08...
  • Page 28 Users of this machine must have a copy of this manual, and must read it before doing any maintenance work. Inspections must be done and documented in accordance with regulations. Signatory’s name and function Date Signature Page 27 VERLINDE S.A. reserves the right to alter or amend the above information without notice KHHOMSBHGB2006/08...

Table of Contents