Warranty - Optex iVision Plus IVP-DU Installation Instructions Manual

PAIRING WITH OTHER iVISION+ DEVICES
NOTE: One Handheld Monitor Unit (IVP-HU) must be configured to have a HOME ID*l
prior to paring up with other iVISION+ devices. Handheld Monitor Unit bundled with
Door Camera Unit already has a HOME ID set up and paired up to each other.
*1 HOME ID is an unique network identification protocol for iVISION+ system.
One Handheld Monitor Unit can issue the HOME ID and all other devices on
the same system must be assigned the same HOME ID.
I
6-1
How to create HOME ID by a Handheld Monitor Unit
&
WARNING
Any pre-existing HOME ID set up will be cleared out with this procedure.
(1) Press "OFF" and then press pairing button in the back of the unit once.
The !VP-HU will be in a pairing mode.
(2) Press the pairing button again and hold until the unit makes a beep sound.
(3) Press "Left function key" on the front to confirm "CREATE."
l
6-2
How to enroll other iVISION+ devices to the Handheld Monitor Unit
(1) Press pairing button in the back of !VP-HU. The unit will be in "PAIRING MODE".
(2) Proceed to "SCAN" by pressing "Left function key". !VP-HU starts scanning for
other devices for 60 seconds.
(3) Prepare other iVISION+ device into their pairing mode. (REF: 6-3)
When the device is ready, the new unit will be enrolled to the HOME ID and
!VP-HU shows which device was connected.
(4) If another device needs to be enrolled, re-enter "SCAN" by "Left Function key"
and repeat the process.
7. OPERATION CHECK
]
7-1
Confirming number of iVISION+ devices in a HOME ID
(1) In a normal operation mode, press and hold the left function key
for two seconds to enter menu mode.
(2) Select menu number 3 # DEVICES IN NETWORK
by up and down key.
(3) Press LEFT function key to "OK"
(4) The display will show the number of iVISION+ devices in the network.
Confirm number of iVISION+ devices registered with the HOME ID.
(5) Maximum numbers of devices in an iVISION+ system are;
2 !VP-DU, 2 !VP-GU and 4 !VP-HU. Go over pairing procedure unless optimal
numbers of devices are displayed.
SPECIFICATION
8-1
Dimensions
I
60mm 2.36"
= =
145mm / 5.71"
Im/..::.. I::: I
I� I 1�, I
&
l..-!:.I � l.2.J
9.

WARRANTY

1. This product is warranted under normal use for 1 year from the date of purchase.
If the product proves to be defective, return it with a copy of your dated sales receipt
for repairs or replacement without charge.
2. The warranty is not applicable when below circumstances will be found:
- Mechanical or electrical modification(s) are made to the product
or it is otherwise altered manually.
- The product is already been at place(s) other than the manufacturer.
- It is determined that the product malfunction has resulted from improper use
or from an accident.
- No copy of the dated sales receipt has been submitted together with the product
to be served.
I
30mm 1.18"
1-------
B]n�m·
80mm / 3.15"
)
6-3
REFERENCE: How to enter "pairing mode" in iVISION+ devices
I
!VP-DU: Door Camera Unit
If not purchased in a bundle package, !VP-DU is
in the pairing mode when powered up. !VP-DU
beeps continuously when PUSH button is pressed.
To purposely enter into a paring mode, press PUSH
button once and hold a pairing button in a back.
I
!VP-HU: Hand held Monitor Unit
If not purchased in a bundle package, IVP-HU is in the
pairing mode when powered up. Choose "JOIN" by
"Right function key" to enroll into an existing HOME ID.
If otherwise, follow the instruction 6-1 to create
a new HOME ID. After an enrollment of new HU,
reset a Time & Date on HUl to reflect the setting
onto the added HU unit.
I
!VP-GU: Gateway Chime Unit
If not purchased in a bundle package, by the factory
default, !VP-GU is in the pairing mode when powered up.
!VP-GU beeps continuously and green/red LED blinks.
Press down both A and B buttons while powering up
the Gateway Chime Unit to enter the pairing mode.
I
7-2
Checking operations on Handheld Monitor Unit
(1) Make sure !VP-HU has been charged and there is a green indication on the top
of display.
•
(2) To confirm RF reception, bring !VP-HU and !VP-DU in a line of sight.
(3) Press "Push button" on a paired Door Camera Unit.
"'"�
-" • • "
All paired IVP-HUs display an image from the !VP-DU.
' ':!
, ... i -
(4) Press "Answer" on any of the !VP-HU.
Voice from !VP-HU will be heard from the !VP-DU.
(5) Press "OFF" on the !VP-HU to terminate the communication.
(6) Move !VP-HU (and !VP-DU) to a desired location and repeat (3) to (5)
to confirm reception of signals.
8-2
Specification Table
MODEL NAME: OPTEX iVISION+ (!VP-HU) Handheld Monitor Unit
Operating Temperature
Operating Humidity
Warranty
Dust/Water Protection
Radiowave Frequency
Power
Use designated battery, !VP-BAT, for JVP·HU.
Please contact your regional technical support for procurement information.
Pairing Button
@
�
�
mr
Pairing button A & B
O to 40 degC (32 to 104 degF)
< 90% RH (no condensation)
1 year
N/ A (Indoor Use Only)
2.4 GHz
Power Adaptor 5.5V DC
@
·:·:::-:.
c;::;i{�Ji;1;f.l
@
ingbutton
/
Sound ON/OFF Switdl