Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Stoelting 100CA
Summary of Contents for Stoelting 100CA
- Page 1 Model 100FA / 100CA / 2217GA OPERATORS MANUAL Manual No. 513653 Mar. 2010...
- Page 3 DO NOT ATTEMPT to operate the machine until instructions and safety precautions in this manual are read completely and are thoroughly understood. If problems develop or questions arise in connection with installation, operation, or servicing of the machine, contact Stoelting. Stoelting Foodservice Equipment Customer Service: 888.429.5920...
- Page 4 CAUTION If you need to replace a part, use genuine Stoelting The signal word “CAUTION” indicates a potentially parts with the correct part number or an equivalent hazardous situation, which, if not avoided, may result part.
-
Page 5: Table Of Contents
TABLE OF CONTENTS SECTION DESCRIPTION PAGE SECTION 1 INTRODUCTION ......................Description ........................Specifications ........................SECTION 2 INSTALLATION INSTRUCTIONS ..................Safety Precautions ......................Shipment and Transit ...................... Freezer Installation ......................Adjusting Cup Dispensers ....................SECTION 3 INITIAL SET-UP AND OPERATION ................. Operator's Safety Precautions .................. - Page 6 LIST OF ILLUSTRATIONS Figure Illustration Page Model 100C - Front ........................Model 100C - Side ........................Model 100F/2217G - Front ......................Model 100F/2217G - Side ......................Adjustable Leg .......................... Warning Label Locations - 100C ....................Warning Label Locations - 100F/2217G ..................Space &...
-
Page 7: Introduction
SECTION 1 INTRODUCTION 1.1 DESCRIPTION Models 100CA, 100FA, and 2217GA freezers are gravity This manual is designed to assist qualified service fed. The freezers are equipped with fully automatic controls personnel and operators in the installation, operation to provide a uniform product. The freezers are designed to... - Page 8 AIR OUT Figure 1 Figure 2 Model 100CA - Side Model 100CA - Front Figure 3 Figure 4 Model 100FA/2217GA - Front Model 100FA/2217GA - Side NOTE: Figures in parenthesis are in centimeters.
-
Page 9: Installation Instructions
SECTION 2 INSTALLATION INSTRUCTIONS 2.1 SAFETY PRECAUTIONS NOTICE Do not attempt to operate the freezer until the safety Accurate leveling is necessary to insure proper operation precautions and operating instructions in this manual are and correct drainage of freezer barrel. read and completely understood. -
Page 10: Warning Label Locations - 100C
IMPORTANT NOTICE TO OPERATOR BEFORE INSTALLING EQUIPMENT, READ THE OWNER'S MANUAL CAREFULLY. TAKE NOTE OF ALL INSTRUCTIONS AND CAUTION DECALS ON THIS EQUIPMENT. GO OVER THE MANUAL THOROUGHLY AND POINT OUT ALL DECALS TO YOUR EMPLOYEES, SO THEY UNDERSTAND HOW TO SAFELY OPERATE THIS EQUIPMENT. -
Page 11: Warning Label Locations - 100F/2217G
IMPORTANT NOTICE TO OPERATOR BEFORE INSTALLING EQUIPMENT, READ THE OWNER'S MANUAL CAREFULLY. TAKE NOTE OF ALL INSTRUCTIONS AND CAUTION DECALS ON THIS EQUIPMENT. GO OVER THE MANUAL THOROUGHLY AND POINT OUT ALL DECALS TO YOUR EMPLOYEES, SO THEY UNDERSTAND HOW TO SAFELY OPERATE THIS EQUIPMENT. -
Page 12: Space & Ventilation Requirements
D. The floor model freezers are equipped with air-cooled WARNING condensers and require correct ventilation. The front of the freezer is the air intake and must be unobstructed. Do not alter or deform electrical plug in any way. Air discharges out of the rear of the unit. Do not obstruct Altering the plug to fit into an outlet of different configu- the discharge. -
Page 13: Adjusting Cup Dispensers
2.4 ADJUSTING CUP DISPENSERS To adjust the cup dispensers, install the size cup desired into the dispenser and turn the wing nut on the dispenser mounting bracket until enough tension is applied to the rim of the cup to keep it from dropping out (Fig. -
Page 15: Initial Set-Up And Operation
SECTION 3 INITIAL SET-UP AND OPERATION 3.1 OPERATOR'S SAFETY PRECAUTIONS G. Do not operate under unsafe operating conditions. A. Know the freezer. Read and understand the Operating Never operate the freezer if unusual or excessive Instructions. noise or vibration occurs. B. -
Page 16: Draining The Freezer For Disassembling And Cleaning
E. SPIGOT ASSEMBLY STIRRING ONLY-OFF-STIRRING & FREEZING SWITCH The STIRRING ONLY-OFF-STIRRING & FREEZ- Dispensing of frozen mix is done by the SPIGOT ING switch is a three-position toggle switch used to ASSEMBLY. By pulling the spigot plunger out, mix control the operation of the refrigeration system and in the form of ice crystals is dispensed through the agitator. -
Page 17: Draining Product
Inspection for worn or broken parts should be made during every disassembly of the freezer for cleaning or other purposes. All worn or broken parts should be replaced to ensure safety to both the operator and the customer, and to maintain good freezer performance as well as a quality product. -
Page 18: Removing Spigot Assembly
Figure 16 Figure 15 Removing Spigot O-Ring from Spigot body Removing Spigot Assembly KNOB SPLASH DEFLECTOR SHAFT FOR SPIGOT SPACER SPRING O-RING SHAFT & PLUG RETAINER CAP ASSEMBLY Figure 17 Cut-away View of Spigot Assembly... -
Page 19: Removing Drive Cap And O-Ring
1. With a clean, dry towel, wipe excess lubricant from the 2. Remove the sealer ring by squeezing the looped spigot assembly and o-ring. Firmly grasp the spigot section and lifting out of the product cylinder (Fig. 19). assembly with both hands and squeeze the o-ring upward (Fig 16). -
Page 20: Removing Divider Plate From Agitator Fingers
5. Unscrew the divider plate from the agitator fingers and remove (Fig.21). Figure 21 Removing Divider Plate from Agitator Fingers 6. Remove the drive shaft by pulling straight up and out of the vertical center post (Fig.22). Figure 23 Exploded View of Divider Plate and Agitator Assembly 7. -
Page 21: Sanitizing The Freezers And Freezer Parts
3.5 SANITIZING THE FREEZER AND FREEZER CAUTION PARTS After the freezer parts have been soaked and washed in Avoid prolonged contact of sanitizer with freezer parts. warm, soapy water, they should be rinsed thoroughly in Prolonged contact of sanitizer with freezer may cause clean water. -
Page 22: Installing Divider Plate And Agitator Assembly
2. Install the drive shaft into the center post by rotating and pressing down lightly on the shaft until the shaft drops down and engages with the gear BACK box shaft. 3. Replace the plastic lower bushing to the bottom of the vertical center post. -
Page 23: Mix Information
3.8 FREEZE DOWN AND OPERATION B. Assemble o-rings onto the spigot plungers without A. With mixed Slush Puppie neutral base in the product lubricant. Then apply a thin film of sanitary lubricant cylinder, start the freezing process by setting the to the exposed surfaces of the o-rings. -
Page 24: Extended Storage
A. DAILY 3.12 EXTENDED STORAGE 1. The exterior should be kept clean at all times to preserve the lustre of the stainless steel. A mild Refer to the following steps for storage of the freezer over alkaline cleanser is recommended. Use a soft any long period of time: cloth or sponge to apply the cleanser. -
Page 25: External Parts To Be Cleaned
CUP DISPENSERS AND LIDS COVERS LIQUID LEVEL INDICATOR FLAVOR BOTTLES SANI-TRAY AND INSERT ALL PANELS Figure 28 External Parts To Be Cleaned... -
Page 27: Decals And Tags
SECTION 4 DECALS AND TAGS 4.1 HOW TO ORDER DECALS AND TAGS To assure receipt of the proper warning decals, supply your dealer or distributor with the following information: A. Model number of equipment. B. Serial number of model, stamped on nameplate. C. - Page 29 PLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE. 3. Remedies: Stoelting’s sole obligations, and Buyer’s sole remedies, for any breach of this warranty shall be the repair or (at Stoelting’s option) replacement of the affected component at Stoelting’s plant in Kiel, Wisconsin, or (again, at Stoelting’s option) refund of the purchase price of the affected equipment, and, during the first ninety (90) days of...