Page 2
This document is the property of Gruppo Piazzetta S.p.A.; it may not be divulged in part or in whole to third parties without written per- mission from Gruppo Piazzetta S.p.A. Gruppo Piazzetta S.p.A. reserves all its statutory rights.
DT2010847 00 1.0 GENERAL RULES Ensure that the installation of your product conforms to all the following instructions. Fig. 1 CHIMNEY STACK FLUE CONNECTION TO FLUE INSPECTION HOLE SOOT REMOVAL INSPECTION HOLE FRESH AIR IN TAKE SAFETY DISTANCES CHECK OF FLOOR LOAD-BEARING CAPACITY DT2030048 00 H07020660 / DT2000245 - Rev.
DT2030049 00 If the flue pipe is an incorrect size or installed other than in compliance with the above instructions, Gruppo Piazzetta Fig. 3 Fig. 4 S.p.A. cannot be held liable for malfunctioning of the product, damage to property or injury to persons or animals.
DT2010025 00 Chimney stack Fig. 7 Fig. 8 The chimney stack is a device fitted on the top of the chimney that is de- signed to aid dispersion of the products of combustion in the atmos- phere. The chimney stack must comply with the following requirements: - it must have an internal section and shape the same as the flue (A);...
DT2010539 03 Fresh air intake Fig. 12 Fig. 13 To ensure trouble-free operation the stove/fireplace must have the necessary air available for combustion and this is provided through the fresh air intake. The fresh air intake must: - have a total free cross section at least equal to the size given in the paragraph “Technical data”;...
DT2010033 01 Installation environment The appliance should be installed in a location which allows safe and convenient use as well as easy maintenance. If the product being in- stalled requires an electrical socket, the room must also be provided with an earthed power supply in accordance with current regulations. The room where the appliance is to be installed must comply with the following requirements: they must not be used as a garage, store for combustible material or for activities with a risk of fire.
550-600° C. MAX 2M MAX 2M It is advisable to use Gruppo Piazzetta S.p.A. pipes and elbows for connection to the flue, since the appliance flue collar is sized for in- sertion of these. Furthermore, the elbows have an inspection door allowing control, cleaning and maintenance of the system.
Page 10
When connecting to the flue there must be a minimum clearance of Fig. 20 BAFFLE PLATE Fig. 21 INSULATING MATERIAL 40 cm from building elements sensitive to heat or from combustible materials (cladding, wooden beams or ceilings, etc.). See figures 17- 18-19-25-26.
Measurement C Measurement D e902 e905 Approx. calculation of height “F” Example on stove e902 with a single one-metre pipe“T100” and one elbow “C6” C (Stove joint) Pipe length Pipe joint Elbow C6 Make the hole for connection to the flue at a height of 212 cm Then fix the wall connector pipe and the trim collar.
DT2010027 02 1.11 NORMATIVE DI RIFERIMENTO Prevention of domestic fires The product must be installed and used in compliance with the manufacturer’s instructions and European and national standards as well as local regulations. when a flue pipe passes through a wall or a ceiling, special installation methods must be applied (protection, thermal insulation, distances from heat-sensitive materials, etc.) See the paragraph “Connection to the flueway”...
Description of the appliance Piazzetta stoves always offer cutting-edge technology in line with the strictest requirements in terms of thermal performance and protection of the environment; with their aesthetic and functional features they represent an answer for truly special heating.
DT2010880 01 Technical data e902 e905 U.M. Rated heat output Consumption at rated heat output Thermal efficiency 84.5 84.5 CO content (with 13% O 0.09 0.09 Approved in accordance with standard EN 13240 EN 13240 Test report No. CPD-10-007 CPD-10-007 Flue diameter Ø14...
DT2010891 00 3.0 USE • Certain basic facts can be all-important for best performance and getting the most out of your appliance. Please find below some basic in- formation intended to be of use with regard to the choice of firewood, the adjustment of the dampers and proper operation of the appliance. •...
Fig. 28 Log size The size of the wood logs can also affect the efficiency of the prod- uct. - It is essential for the wood to be arranged on the grate on top of a layer of embers. - The logs must not touch the aluker or the glass window nor must they be put on top of each other.
2. Start-up - During this first time of operation it is recommended to use the appliance at minimum capacity, stoking the grate for at least the first day with only 50% of the logs usually indicated as normal. - Keep the air dampers in the operating position (except for lighting), see paragraph “Combustion air regulation”. - This stage allows all the parts to settle down and fumes caused by paints/varnishes, greases or oily liquids used in manufacture to dis- appear.
DT2010048 00 Operation under adverse weather conditions During the intermediate seasons with adverse weather conditions or when outdoor temperatures are higher, a sudden rise can cause mal- functioning of the draught, thereby impeding proper smoke discharge. In this case the grate must be loaded with only a little wood and the primary air damper be set fully open so that the wood burns faster and thereby stabilises the draught.
750°C. This can only be broken by a heavy impact, such as banging the door too hard. In case of breakage replace with original Gruppo Piazzetta S.p.A parts only. Do not use any material that could scratch or spoil the glass, as scratches may develop into cracks or breaks...
Proper tightness of the door seal is essential for optimal product performance. It is therefore recommended that the seals be checked peri- odically or after a long period of use for signs of wear or damage. If necessary replace them using Gruppo Piazzetta S.p.A. original spare parts.
DT2010069 00 5.0 TROUBLESHOOTING Some of the above problems could be resolved by following the instructions. Only qualified persons must carry out work on the stove and only when it is cold. Unauthorised tampering with the appliance or use of other than original spare parts invalidates the warranty and relieves the manufacturer of all and any liability.
Page 23
There are still flames remain in the grate This instruction booklet contains all the useful information for installation, operation and maintenance. Only call the Gruppo Piazzetta S.p.A. service centre after having scrupulously followed all the instructions. H07020660 / DT2000245 - Rev. 03...
Page 26
Seriennummer des Produkts. Bei Anfordern des technischen Kundendiensts der Gruppe Piazzetta immer angeben. N° de série du produit à spécifier au Centre d’assistance Technique de la Sté Gruppo Piazzetta en cas de demande d’intervention. Via Montello, 22 31011 Casella d’Asolo (TV) - ITALY Tel.
Need help?
Do you have a question about the e902 and is the answer not in the manual?
Questions and answers