Advertisement
Submersible Two-Stage Grinder Pump
IMPORTANT!
Read all instructions in this manual before operating pump.
As a result of Crane Pumps & Systems, Inc., constant product improvement program,
product changes may occur. As such Crane Pumps & Systems reserves the right to
change product without prior written notifi cation.
A Crane Co. Company
420 Third Street
Piqua, Ohio 45356
Phone: (937) 778-8947
Fax: (937) 773-7157
www.cranepumps.com
MENU
HOME
INSTALLATION MANUAL
83 West Drive, Bramton
Ontario, Canada L6T 2J6
Phone: (905) 457-6223
Fax: (905) 457-2650
Manual Index
Series: OGP
2 HP, 3450 RPM,
60 Hz.
Form No. 119972-Rev. H
Advertisement
Table of Contents
Related Manuals for CRANE PUMPS & SYSTEMS OGP Series
Summary of Contents for CRANE PUMPS & SYSTEMS OGP Series
- Page 1 MENU HOME Manual Index INSTALLATION MANUAL Submersible Two-Stage Grinder Pump Series: OGP 2 HP, 3450 RPM, 60 Hz. IMPORTANT! Read all instructions in this manual before operating pump. As a result of Crane Pumps & Systems, Inc., constant product improvement program, product changes may occur.
-
Page 2: Safety First
MENU HOME Manual Index SAFETY FIRST! Please Read This Before Installing Or Operating Pump. WARNING! - DO NOT pump hazardous materials This information is provided for SAFETY and to PREVENT (fl ammable, caustic, etc.) unless the pump is specifi cally EQUIPMENT PROBLEMS. - Page 3 MENU HOME Manual Index USER GUIDE Congratulations on your purchase of a Barnes grinder pump generates suffi cient pressure grinder pump system. With proper care and by to pump this slurry from your home to the following a few simple guidelines your grinder wastewater plant.
-
Page 4: Pump Specifications
MENU HOME Manual Index PUMP SPECIFICATIONS: DISCHARGE ....... 1¼” NPT, Vertical, Bolt-on Flange SPEED ........ 3450 RPM, 60Hz LIQUID TEMPERATURE ..104°F (40°C) Continuous UPPER BEARING: MOTOR HOUSING ..... Cast Iron ASTM A-48, Class 30 Design ..... Single Row, Angular Contact Ball VOLUTE ...... - Page 5 MENU HOME Manual Index inches OGP2022CC - For “C” Channel (mm) OGP2022CE - For EcoTRAN™...
- Page 6 MENU HOME Manual Index OGP2022CO - For Replacement Core Unit inches (mm) OGP2022CT - Threaded...
- Page 7 MENU HOME Manual Index OGP2022AUE inches (mm) MODEL VOLT NEMA FULL LOCKED CORD CODE CORD CORD WINDING START LOAD ROTOR SIZE TYPE O.D. LENGHT RESISTANCE CODE AMPS AMPS ± .02 (.5) Ft. (m) MAIN -- START in (mm) OGP2022L 16.5 53.8 12/3 .61 (15.5)
- Page 8 MENU HOME Manual Index The nameplate is located on top of the pump. This contains the pumps part number, horsepower voltage, phase, and serial number, as well as other information. The start-up form located in the back of this manual contains a place to record this data.
-
Page 9: Installation
MENU HOME Manual Index RECEIVING/UNPACKING: Upon receiving the pump, it should be inspected for dam- age or shortages. If damage has occurred, fi le a claim immediately with the company that delivered the pump. Unpack pump and record pump serial and model number before installing. -
Page 10: Cable Connections
MENU HOME Manual Index Wire Size - If additional cable is required consult a qualifi ed electrician for proper wire size. CABLE CONNECTIONS: Power/Control Cable- Insert female end of cable plug into housing bore aligning alignment mark with hole in terminal block see Figures 4 &... - Page 11 MENU HOME Manual Index Single phase 240 Volt AC, 60Hz FIGURE 6 “L” Series, 12/3 SOW Wiring Harness Item 54 on Figure 8 Single phase 240 Volt AC, 60Hz AUE, CC, CE, CO, CT, Series, 12/5 SOW FIGURE 7...
-
Page 12: Troubleshooting
MENU HOME Manual Index TROUBLE SHOOTING CAUTION ! Always disconnect the pump from the electrical power source before handling. If the system fails to operate properly, carefully read instructions and perform maintenance recommendations. If operating problems persist, the following chart may be of assistance in identifying and correcting them: MATCH “CAUSE”... - Page 13 MENU HOME Manual Index Compact Series - CC, CE, CO, CT FIGURE 8...
- Page 14 MENU HOME Manual Index Standard Series - L & AUE FIGURE 9...
-
Page 15: Parts Kits
MENU HOME Manual Index PARTS KITS Seal Repair Kit ...P/N: 116664 Item #’s: 6, 7, 13, 15, 20, 25, 33, 36, 38 Overhaul Kit ....P/N: 116665 Item #’s: 3, 5, 6, 7, 9, 13, 15, 20, 25, 28, 29, 33, 36, 38 Cutter Kit ....P/N: 116666 Item #’s: 5, 6, 7, 9, 13, 15, 36 PARTS LIST... - Page 16 MENU HOME Manual Index MOVEABLE ASSEMBLY P/N: 116596* (OGP-L) & 116597* (OGP-AU) PARTS LIST For Grinder, “C” Channel Basin Package ITEM QTY. PART No. DESCRIPTION 112354 Check Valve/Upper Moveable 116605 Upper Pump Bracket Assy - OGP 116606 Upper Pump Bracket Assy - OGP-AU 102174 Pipe Nipple 107360...
- Page 17 MENU HOME Manual Index DISCHARGE ASSEMBLIES for CC, CE, CO & CT Grinder Pumps ITEM QTY. PART No. DESCRIPTION 121225 O-ring, 4mm 118251 Valve Seat Flapper, Brz 118252 Gasket 120825 Pin .125 x .75 SS 1-156-1 HXHD Screw 5/16-18 x 1.00” SS 3 or 6 026322 Lock Washer 5/16 SS...
- Page 18 MENU HOME Manual Index Limited 2 Year Warranty We warrant that products of our manufacture will be free of defects in material and workmanship under normal use and service for twenty-four (24) months after notice of owner’s acceptance, but no greater than twenty-seven (27) months after receipt of shipment, when installed and maintained in accordance with our instructions.
-
Page 19: Final Check
MENU HOME Manual Index START-UP / WARRANTY REGISTRATION FORM This form is designed to provide assurance that customer service and a quality product are the number one priority with Crane Pumps & Systems, Inc. Please fi ll out the following questions as completely and accurate as possible. When complete, mail this form to: Crane Pumps &... - Page 20 MENU HOME Manual Index FOLD HERE AND TAPE, DO NOT STAPLE PLACE STAMP HERE CRANE PUMPS & SYSTEMS, INC. WARRANTY SERVICE GROUP 420 THIRD STREET PIQUA, OHIO 45356 - U.S.A.
Need help?
Do you have a question about the OGP Series and is the answer not in the manual?
Questions and answers