Related Manuals for FALCOM FOX3-KMD
Summary of Contents for FALCOM FOX3-KMD
- Page 1 FOX3-KMD ARDWARE ANUAL Version: 1.0.1; Modified: Thursday, December 22, 2016...
-
Page 2: Table Of Contents
6.2.1. NFC Windscreen Port Pinout ..........................18 6.3. NFC InCar (4pin connector) ......................18 6.3.1. NFC InCar Port Pinout ............................18 This confidential document is a property of FALCOM GmbH and may not be copied or circulated without previous permission. Page 2 of 23... - Page 3 - Added RF exposures in both English and French (chapter 8) 12/22/2016 1.0.0 F. Beqiri - Initial version. 11/02/2016 This confidential document is a property of FALCOM GmbH and may not be copied or circulated without previous permission. Page 3 of 23...
- Page 4 Because our products are being continuously improved, specifications and information given in this document are subject to change by FALCOM without notice. This confidential document is a property of FALCOM GmbH and may not be copied or circulated without previous permission. Page 4 of 23...
-
Page 5: Introduction
FOX3-KMD is equipped with SIM-Chips, so there is no need for using a SIM card. The SIM chips should be activated before putting the device into the operation. The physical interface to the devices application is made through integrated 8pin main port. -
Page 6: Security
Check the laws and regulations on the use of cellular devices in the area where you drive. Always obey them. Also, when using your FOX3-KMD while driving, please pay full attention to driving, pull off the road and park before making or answering a call if driving conditions so require. When applications are prepared for mobile use, they should fulfil road-safety instructions of the current law! 2.4. -
Page 7: Aircraft
2.8. Children Do not allow children to play with your FOX3-KMD devices. It is not a toy. Children could hurt themselves or others (by poking themselves or others in the eye with the antenna, for example). Children could damage the modems or make calls that increase your modem bills. -
Page 8: Safety Precautions While Charging The Battery
It is also recommended to use the devices not close to medical devices as for example hearing aids and pacemakers. This confidential document is a property of FALCOM GmbH and may not be copied or circulated without previous permission. Page 8 of 23... -
Page 9: Safety Standards
European Community, Directorate General V in matters of radio frequency electromagnetic energy. This confidential document is a property of FALCOM GmbH and may not be copied or circulated without previous permission. Page 9 of 23... -
Page 10: Technical Data
NMEA Msg.: GLL, GGA, RMC, VTG, GSV, GSA ➢ FALCOM Msg.: IOP, GSM, AREA, 3DP, BIN This confidential document is a property of FALCOM GmbH and may not be copied or circulated without previous permission. Page 10 of 23... -
Page 11: Power Consumption For Fox3-Kmd
Optional. Storage and using conditions of the device with battery option are limited to the battery temperature range. Table 2: Operating temperature for FOX3-KMD This confidential document is a property of FALCOM GmbH and may not be copied or circulated without previous permission. Page 11 of 23... -
Page 12: Gsm/2G/3G Engine Features
➢ Max. update rate: 1 Hz. ➢ A-GPS support: AGPS: Online / Offline / Autonomous ➢ This confidential document is a property of FALCOM GmbH and may not be copied or circulated without previous permission. Page 12 of 23... -
Page 13: Fox3-Kmd Application Interface
5.2. Determining the External Equipment Type Before you connect the serial port pins of the FOX3-KMD devices to an external equipment, you need to determine if the external hardware serial ports are configured as DTE (Data Terminal Equipment) or DCE (Data Communications Equipment). -
Page 14: Hardware Interfaces
4 x mounting holes for attaching the device to a suitable location. Table 4: Interface specifications Figure 1: Interface specifications of the FOX3-KMD device. This confidential document is a property of FALCOM GmbH and may not be copied or circulated without previous permission. Page 14 of 23... -
Page 15: Main Port (8Pin Connector)
Main channel used to output navigation, measurement, response and system data to any software (e.g. HyperTerminal, FALCOM Workbench). This confidential document is a property of FALCOM GmbH and may not be copied or circulated without previous permission. Page 15 of 23... -
Page 16: How To Use I/O1 (Pin 4)
How to use I/O1 (pin 4) This pin has dual functions. It is controlled by the internal firmware of FOX3-KMD. Therefore, the user must define whether to use it as analog or digital pin. The configured digital pin can also be used as input or output while the if configured as analog pin it can only be used as input. -
Page 17: How To Use Ign (Pin 3)
How to connect and communicate with FOX3-KMD To power on and communicate with FOX3-KMD device, you have to connect the power line to an external power source ranging from 10.8 – 32VD and connect the serial port lines to your COM port on your PC as shown below. -
Page 18: Nfc Windscreen (4Pin Connector)
Receive channel from NFC InCar V24, ±12 V Table 7: Description of the NFC InCar port (4-pin connector) This confidential document is a property of FALCOM GmbH and may not be copied or circulated without previous permission. Page 18 of 23... -
Page 19: Led Indicators
ANUAL ERSION 6.4. LED indicators The actual state of the FOX3-KMD can be shown by three LED’s on the front panel of the unit. These programmable LEDs can be interfaced to show the status of the device. Figure 10: View of LED indicators To turn on one of these LEDs, use the following command: $PFAL,IO11.Set=high... -
Page 20: External Antenna Ports
Do not mount the antenna visible on the dashboard but mount it in a location underneath the dashboard. Hiding the antenna is key to successful security in the event of theft. FOX3-KMD devices generate events in case of the GNNS antenna is connected, disconnected or cut off. If an intruder cuts off the GNNS antenna cable, an event is generated which can be used to trigger alarm notifications to the user. -
Page 21: Housing
FOX3-KMD H 1.0.1 ARDWARE ANUAL ERSION 7. HOUSING Figure 13: FOX3-KMD housing This confidential document is a property of FALCOM GmbH and may not be copied or circulated without previous permission. Page 21 of 23... -
Page 22: Rf Exposures
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This confidential document is a property of FALCOM GmbH and may not be copied or circulated without previous permission. Page 22 of 23... -
Page 23: Exposition Rf - French
Connectez l'équipment à une prise dans un circuit different de celui auquel le récepteur est connecté. Consultez votre revendeur ou in téchnicien radio/télévision expérimenté pour du support. This confidential document is a property of FALCOM GmbH and may not be copied or circulated without previous permission. Page 23 of 23...
Need help?
Do you have a question about the FOX3-KMD and is the answer not in the manual?
Questions and answers