ESAB Aristo RoboFeed 3004w Instruction Manual
Hide thumbs
Also See for Aristo RoboFeed 3004w:
- Service manual (34 pages) ,
- Instruction manual (24 pages) ,
- Instruction manual (20 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Service Manual
GB
®
Aristo
RoboFeed 3004w
Î Î Î Î Î Î Î Î Î Î Î Î Î
Î Î Î Î Î Î Î Î Î Î Î Î Î
Î Î Î Î Î Î Î Î Î Î Î Î Î
Î Î Î Î Î Î Î Î Î Î Î Î Î
Î Î Î Î Î Î Î Î Î Î Î Î Î
Î Î Î Î Î Î Î Î Î Î Î Î Î
Î Î Î Î Î Î Î Î Î Î Î Î Î
Î Î Î Î Î Î Î Î Î Î Î Î Î
Î Î Î Î Î Î Î Î Î Î Î Î Î
Î Î Î Î Î Î Î Î Î Î Î Î Î
Î Î Î Î Î Î Î Î Î Î Î Î Î
Î Î Î Î Î Î Î Î Î Î Î Î Î
Instruction manual
0461 165 001 GB 20120808
Valid for serial no. 745-xxx-xxxx
Advertisement
Table of Contents
Related Manuals for ESAB Aristo RoboFeed 3004w
Summary of Contents for ESAB Aristo RoboFeed 3004w
- Page 1 ® Aristo RoboFeed 3004w Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î...
- Page 2 - 2 -...
-
Page 3: Table Of Contents
1 SAFETY ............2 INTRODUCTION . -
Page 4: Safety
SAFETY Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or near the equipment observes all the relevant safety precautions. Safety precautions must meet the requirements that apply to this type of equipment. The following recommendations should be ob... - Page 5 As the person responsible for the equipment, it is your responsibility to obtain information on approved collection stations. For further information contact the nearest ESAB dealer. - 5 - bm51d1ea © ESAB AB 2008...
-
Page 6: Introduction
CAUTION This product is solely intended for arc welding. ESAB can provide you with all necessary welding protection and accessories. INTRODUCTION The RoboFeed 3004w wire feed unit is intended for MIG/MAG welding along with robotic equipment. Equipment The wire feed unit is supplied with an instruction manual and a sticker with recommended wear parts. -
Page 7: Installation
The other end is at the wire feed unit and must be fitted with the terminating resistor, as shown on the right. Example of a robotic welding system - 7 - bm51d1ea © ESAB AB 2008... -
Page 8: Operation
General safety regulations for handling the equipment can be found on page 4. Read through before you start using the equipment! WARNING Assure that the side panels are closed during operation. WARNING Rotating parts can cause injury, take great care. - 8 - bm51d1ea © ESAB AB 2008... -
Page 9: Connection And Control Devices
Connection for welding gun (EURO) Connection for control cable from power source * ELP = ESAB Logic Pump, see 5.2 Ä Ä Ä Ä Ä Ä Ä Ä Ä Ä Ä Ä Ä Ä Ä Ä Ä Ä Ä Ä Ä... -
Page 10: Water Connection
Water connection The wire feed unit with water connection is equipped with a detection system ELP (ESAB Logic Pump) which checks that the water hoses are connected. When connecting a water-cooled welding gun, the water pump starts. Detection only works with power sources that are equipped with ELP. -
Page 11: Wire Feed Pressure
(5) and pulling out the rollers. During installation, repeat the above in the reverse order. Choice of track in the feed rollers Turn the feed roller with the dimensioning mark for the required track towards you. - 11 - bm51d1ea © ESAB AB 2008... -
Page 12: Maintenance
Spare parts may be ordered through your nearest ESAB dealer, see the last page of this publication. - Page 13 NOTES ..............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................- 13 - notes...
-
Page 14: Diagram
Diagram - 14 - © ESAB AB 2008 bm51e... - Page 15 - 15 - © ESAB AB 2008 bm51e...
-
Page 16: Order Number
Denomination Type Note 0461 000 891 Wire feed unit Aristo RoboFeed 3004w 12 pole 0461 030 990 Spare parts list Aristo RoboFeed 3004w Technical documentation is available on the Internet at www.esab.com - 16 - bm51o © ESAB AB 2008... - Page 17 - 17 -...
-
Page 18: Wear Parts
In order to weld with aluminium wire, proper rollers, nozzles and liners for aluminium wire MUST be used, It is recommended to use 3 m long welding gun for aluminium wire, equipped with appropriate wear parts. - 18 - cm51vw © ESAB AB 2008... - Page 19 RoboFeed 3004w - 19 - cm51vw © ESAB AB 2008...
-
Page 20: Accessories
Quick connector MarathonPact ... . F102 440 880 Adapterplate for mounting on the robot arm ..0461 173 880 - 20 - cm51va © ESAB AB 2008... - Page 21 NOTES ..............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................- 21 - notes...
- Page 22 NOTES ..............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................- 22 - notes...
- Page 23 NOTES ..............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................- 23 - notes...
- Page 24 ESAB Romania Trading SRL ESAB VAMBERK s.r.o. SOUTH AFRICA ESAB Mexico S.A. Bucharest Vamberk ESAB Africa Welding & Cutting Ltd Monterrey Tel: +40 316 900 600 Tel: +420 2 819 40 885 Durbanvill 7570 - Cape Town Tel: +52 8 350 5959...
Need help?
Do you have a question about the Aristo RoboFeed 3004w and is the answer not in the manual?
Questions and answers