Installation Instructions - Kogan KA9FUNOVENA Instruction And Installation Manual

Installation Instructions

It's important to carefully read the following
installation instructions before beginning the
installation of your oven.
Important.
The connection of this oven must be carried out by a
suitably qualified and licensed person, in accordance
with the current versions of the following:
– AS/NZS 3000 Wiring Rules
– Electricity Safety Regulations 2010
– The installation instructions within this user manual
The adjacent cabinetry and wall materials must be able to withstand a minimum temperature rise of 85°C
above the ambient temperature of the room.
Note: Ensure there is a grounded socket nearby (behind
the unit). A dedicated power circuit is recommended
• The kitchen area sho
the oven, easy access to all control elements should be ensured.
for the unit but not required. Additional electrical
•
This is a built-in oven and has been designed to be housed within an oven cabinet.
appliances on the same circuit may exceed the current
Coating or veneer used on cabinetry must be applied with a heat resistant adhesive
The adjacent cabinetry and wall materials must be able to withstand a minimum temperature rise of 85°C
(amperage) rating for that circuit. If after the installation
above the ambient temperature of the room.
(rated to 100°c). This prevents surface deformation or detachment of the coating. In the
of your unit the circuit breaker trips or the fuse fails on
case of vinyl wrap kitchens, it is strongly recommended to have heat de
a repeated basis then a dedicated circuit will likely be
on either side of the oven cabinet.
required.
• Your oven cabinet should be made to suit the following dimensions and can be either a
tall or underbench cabinet to suit your kitchen design.
Make sure that the electrical circuit is disconnected or fuse removed, then connect the
•
oven into the mains supply.
IMPORTANT.
•
the oven into place (refer to the diagram below).
IMPORTANT.
Note: It is a requirement for a ventilation gap to be cut into the oven cabinet as per below diagrams.
Note:
Installation Instructions
PO ITIONIN
Installation Instructions
PO ITIONIN
• The kitchen area sho
the oven, easy access to all control elements should be ensured.
• This is a built-in oven and has been designed to be housed within an oven cabinet.
Coating or veneer used on cabinetry must be applied with a heat resistant adhesive
(rated to 100°c). This prevents surface deformation or detachment of the coating. In the
case of vinyl wrap kitchens, it is strongly recommended to have heat de
on either side of the oven cabinet.
•
he installation/connection should only be completed by a licensed electrician. Your oven cabinet should be made to suit the following dimensions and can be either a
tall or underbench cabinet to suit your kitchen design.
Make sure that the electrical circuit is disconnected or fuse removed, then connect the
•
oven into the mains supply.
he installation/connection should only be completed by a licensed electrician.
•
the oven into place (refer to the diagram below).
It is a requirement for a ventilation gap to be cut into the oven cabinet as per below diagrams.
POSITIONING
The adjacent cabinetry and wall materials must be able
to withstand a minimum temperature rise of 85°C above
the ambient temperature of the room.
• The kitchen area should be dry and equipped with
sufficient ventilation. When installing the oven, easy
access to all control elements should be ensured.
• This is a built-in oven and has been designed to be
housed within an oven cabinet.
• Coating or veneer used on cabinetry must be applied
with a heat resistant adhesive (rated to 100°c). This
prevents surface deformation or detachment of
the coating. In the case of vinyl wrap kitchens, it is
strongly recommended to have heat deflectors on
either side of the oven cabinet.
• Your oven cabinet should be made to suit the
following dimensions and can be either a tall or
underbench cabinet to suit your kitchen design.
• Make sure that the electrical circuit is disconnected or
fuse removed, then connect the oven into the mains
supply.
IMPORTANT
The installation/connection should only be completed
by a licensed electrician.
• Insert the oven completely into the oven cabinet and
use the four screws supplied to fix the oven into place
(refer to the diagram below).
Note: It is a requirement for a ventilation gap to be cut
into the oven cabinet as per below diagrams.
9
9
7