Download  Print this page

Siemens CP 1243-1 PCC Operating Instructions Manual

Telecontrol.
Hide thumbs

Advertisement

CP 1243-1 PCC
SIMATIC NET
S7-1200 - TeleControl
CP 1243-1 PCC
Operating Instructions
Siemens Automation
02/2015
C79000-G8976-C384-01
___________________
Preface
___________________
Application and properties
___________________
Requirements for use
___________________
LEDs and connectors
___________________
Installation, connecting up,
commissioning
___________________
Configuration and operation
___________________
Diagnostics and upkeep
___________________
Technical specifications
___________________
Approvals
___________________
Dimension drawings
___________________
Documentation references
1
2
3
4
5
6
7
A
B
C

Advertisement

Table of Contents

   Related Manuals for Siemens CP 1243-1 PCC

   Summary of Contents for Siemens CP 1243-1 PCC

  • Page 1 ___________________ CP 1243-1 PCC Preface ___________________ Application and properties ___________________ SIMATIC NET Requirements for use ___________________ LEDs and connectors S7-1200 - TeleControl CP 1243-1 PCC ___________________ Installation, connecting up, commissioning ___________________ Configuration and operation Operating Instructions ___________________ Diagnostics and upkeep...
  • Page 2 Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.
  • Page 3: Preface

    Article number6GK7 243-1HX30-0XE0 Hardware product version 2 Firmware version V2.0 The CP 1243-1 PCC for Plant Cloud Communication / Data Driven Services is the communications processor for connecting the SIMATIC S7-1200 via a public infrastructure (e.g. DSL) to an operation center.
  • Page 4 This abbreviation will be used below instead of the full term "Plant Cloud in the operation center". ● CP The term "CP" is used below instead of the full product name CP 1243-1 PCC. ● STEP 7 This short form will be used below for the STEP 7 Basic / Professional configuration tool.
  • Page 5 You will also find information about the diagnostics options of the device. Current manual release on the Internet You will also find the current version of this manual on the Internet pages of Siemens Industry Online Support in the directory with following entry ID: 51297224 (http://support.automation.siemens.com/WW/view/en/51297224)
  • Page 6 Siemens recommends strongly that you regularly check for product updates. For the secure operation of Siemens products and solutions, it is necessary to take suitable preventive action (e.g. cell protection concept) and integrate each component into a holistic, state-of-the-art industrial security concept.
  • Page 7: Table Of Contents

    Security functions ........................39 5.8.1 Firewall ............................ 39 5.8.1.1 Firewall sequence when checking incoming and outgoing frames ........39 5.8.1.2 Notation for the source IP address (advanced firewall mode) ..........39 Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 8 Diagnostics options ........................ 55 Downloading firmware ......................56 Module replacement ......................59 Technical specifications ........................61 Technical specifications of the CP 1243-1 PCC ..............61 Pinout of the Ethernet interface ..................... 62 Approvals ............................. 63 Dimension drawings ..........................67 Documentation references ........................69 Index ..............................
  • Page 9: Application And Properties

    Remember the following requirements in the CP configuration for Plant Cloud Communication: ● Activation of Plant Cloud Communication ("Communication types" parameter group). ● IP address assignment: Set the IP address manually or obtain the IP address from a DHCP server. Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 10: Communications Services

    ● S7 communication and PG/OP communication with the following functions: – PUT/GET as client and server for data exchange with remote stations (S7- 300/400/1200/1500) – PG functions – Operator control and monitoring functions (HMI) CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 11: Other Services And Properties

    The Plant Cloud Communication with the operation center is started in the following way: – Triggered by various selectable criteria. ● Analog value processing Analog values can be preprocessed on the CP according to various methods. Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 12 Secure communication with one or two operation centers. ● Logging To allow monitoring, events can be stored in log files that can be read out using the configuration tool or can be sent automatically to a Syslog server. CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 13: Configuration Limits And Performance Data

    Configuration limits and performance data Number of CMs/CPs per station In each S7-1200 station, up to three CMs/CPs can be plugged in and configured; this allows three CP 1243-1 PCC modules. Connection resources ● TCP connections The CP can establish connections to up to 8 communications partners (S7 stations).
  • Page 14 ● Maximum 226 rules with individual addresses ● Maximum 30 rules with address ranges or network addresses (e.g. 140.90.120.1 - 140.90.120.20 or 140.90.120.0/16) ● Maximum 128 rules with limitation of the transmission speed ("Bandwidth limitation") CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 15: Requirements For Use

    To configure the CP, the following configuration tool is required: ● STEP 7 Basic / Professional V13 SP1 with HSP0112 Software for online functions STEP 7 in the version specified above. Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 16 Requirements for use 2.2 Software requirements CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 17: Leds And Connectors

    Open the upper or lower cover of the housing by pulling it down or up as shown by the arrows in the illustration. The covers extend beyond the housing to give you a grip. Figure 3-1 Opening the covers of the housing Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 18: Leds

    When the module starts up, all its LEDs are lit for a short time. Multicolored LEDs display a color mixture. At this point in time, the color of the LEDs is not clear. CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 19 Physical connection established, partner not responding, CPU in RUN Physical connection established, partner not responding, CPU in STOP Connection for online functions Connection for online functions estab- lished No connection to engineering station Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 20: Electrical Connectors

    The Ethernet connector is located behind the lower hinged cover of the module. The interface is an RJ-45 jack according to IEEE 802.3. The pin assignment and other data relating to the Ethernet interface can be found in the section Technical specifications (Page 61). CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 21: Installation, Connecting Up, Commissioning

    Blitzductor BVT AVD 24, article number 918 422 or a comparable protective element. Manufacturer: DEHN+SOEHNE GmbH+Co.KG Hans Dehn Str.1 Postfach 1640 D-92306 Neumarkt, Germany 4.1.1 Notices on use in hazardous areas WARNING EXPLOSION HAZARD DO NOT OPEN WHEN ENERGIZED. Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 22 The device may only be operated in an environment with pollution degree 1 or 2 (see IEC 60 664-1). WARNING When used in hazardous environments corresponding to Class I, Division 2 or Class I, Zone 2, the device must be installed in a cabinet or a suitable enclosure. CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 23: General Notices On Use In Hazardous Areas According To Atex

    This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D or non- hazardous locations only. This equipment is suitable for use in Class I, Zone 2, Group IIC or non-hazardous locations only. Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 24: Installing, Connecting Up And Commissioning

    When installing and connecting up, keep to the procedures described in the system manual "S7-1200 Programmable Controller". Pulling/plugging the module NOTICE Turning off the station when plugging/pulling the module Before pulling or plugging the module, always turn off the power supply to the station. CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 25 The inner dimension of the hole for the DIN rail mounting clips is 4.3 mm. Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 26 Vertical installation of the rack: -20 °C to +60 °C Requirement: Configuration prior to commissioning One requirement for the commissioning of the module is the completeness of the STEP 7 project data (see below, step 5). CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 27 STEP 7 information system: "Loading project data" • "Using online and diagnostics functions" • Close the front covers of the module and keep them closed during operation. Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 28 Installation, connecting up, commissioning 4.2 Installing, connecting up and commissioning CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 29: Configuration And Operation

    PLC tags must also be created to assign the user data to be transferred to the data points. When assigning the PLC tags to your communications partners, you can select both operation centers. For more detailed information, refer to the following sections. Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 30 Using the "Download to device" function, the STEP -7 project data including the configuration data of the CPs is downloaded to the relevant CPU. You will find further information on the individual steps in the following sections and in the help system of STEP 7. CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 31: Address And Authentication Information

    4. Select any row in the table "Trusted certificates and root certification authorities". 5. Select the "Import" entry in the shortcut menu. 6. In the dialog that follows, select the required certificate. Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 32: Configuring Data Points And Messages

    The values of the PLC tags or DBs referenced by the data points are read and transferred to the communications partner by the CP. Data received from the communications partner is written by the CP to the CPU via the PLC tags or DBs. CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 33: Datapoint Types

    The data point types supported by the CP along with the compatible S7 data types are listed below. They are grouped according to format (memory requirements). Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 34 If the array is modified later, the data point must be recreated. Time stamp in UTC format Time stamps are transferred in UTC format (48 bits) and contain the time difference in milliseconds since 01.01.1970. CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 35: Cpu Scan Cycle

    Since no fixed time can be configured for the cycle and since the individual phases cannot be assigned a fixed number of objects, the duration of the scan cycle is variable and can change dynamically. Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 36: Types Of Transmission, Event Classes, Triggers, Status Identifiers

    The frame memory operates chronologically; in other words, the oldest frames are sent first (FIFO principle). When the maximum number of events is reached and the frames could not be sent, the oldest values are overwritten. CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 37 If the memory area of the trigger bit is in the bit memory or in a data block, the trigger bit is reset to zero when the data point is transferred. Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 38 Value not Value is does not value ator control value over- value: Val- updated invalid exist or S7 flow before ue range after start address reading the exceeded unreacha- value (always 0) Bit status CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 39: Security Functions

    In "Security > Log settings > Configure system events", set the "Level:" parameter to the value "3 (Error)" to ensure the reliable establishment of the communications connections. Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 40: Time-of-day Synchronization

    If you use security functions, a valid time of day is extremely important. It is recommended to use the NTP (secure) method. Configuration For information on configuration, refer to the STEP 7 online help of the "Time-of-day synchronization" parameter group. CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 41: Snmp

    The information on the properties of SNMPcompliant devices is entered in MIB files (MIB = Management Information Base). Range of performance of the CP as an SNMP agent The CP supports data queries over SNMP in the following version: ● SNMPv1 (standard) Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 42 The other groups of the MIB II standard are not supported: – Address Translation (AT) – EGP – Transmission ● Siemens Automation MIB The following exceptions / restrictions apply to the CP. Write access is permitted only for the following MIB objects of the system group: – sysContact –...
  • Page 43: Step 7 Configuration Of Individual Parameters

    If you configure S7 connections to the relevant station, and these run via the CP, you will need to enable this option. "SNMP" parameter group ● Enable SNMP Enables communication using SNMP on the CP. If security functions are enabled, you will find the entry in "Security". Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 44: Ethernet Interface (x1) > Advanced Options

    CP. You have option of configuring two operation centers. ● Operation center number The Operation center number in this parameter group is set by the system. It is required for data point configuration. CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 45: Operation Center1 Or Operation Center2

    – Default setting: 1 s; if you enter 0 (zero), the function is deactivated. The monitoring time is configured for the Ethernet interface as the default for all TCP connections. The default value can be adapted individually for each connection in "Operation center". Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 46 As soon as the fill level drops below 50%, bits 2 and 3 are reset to 0. Bits 4 to 15 of the PLC tags are not used and do not need to be evaluated in the program. CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 47: Communication With The Cpu

    The following characters are forbidden since they do not adhere to the syntax rules of the operation center for OPC items: ● 0x27 (apostrophe) ● 0x2e (period) ● 0x2f (slash) ● 0x5b and 0x5d (square brackets) ● 0x5c (backslash) ● 0x7c (pipe) Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 48: Threshold Value Trigger And Analog Value Preprocessing

    – Adjustment to the start of measuring range and end of measuring range (if configured) 5. Storage of the value in the send buffer Transfer of the value to the partner if trigger and threshold value conditions are met. CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 49: Analog Value Preprocessing

    ● 1 = No smoothing ● 4 = Weak smoothing ● 32 = Medium smoothing ● 64 = Strong smoothing If mean value generation is active, this parameter has no effect. Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 50 (for example triggered by the trigger) to the time of the request. Once again, the accumulation restarts so that the next mean value can be calculated. CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 51 This avoids a frame being sent every time a limit value is violated if the analog value fluctuates close to one of the two limit values for a longer period of time. Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 52: Threshold Value Trigger

    The deviations of the current process value are totaled in each calculation cycle. The trigger is set only when the totaled value reaches the configured value of the threshold value trigger and a new process value is entered in the send buffer. CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 53 In this example, if a deviation of the process value of approximately 0.5 should fire the trigger, then with the behavior of the process value shown here a threshold value of approximately 1.5 ... 2.5 would need to be configured. Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 54 Configuration and operation 5.11 STEP 7 configuration of individual parameters CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 55: Diagnostics And Upkeep

    If you want to operate online diagnostics with the station via the CP, you need to select Activate online functions, see section Communication types and SNMP (Page 43). You will find further information on the diagnostics functions of STEP 7 in the STEP 7 information system. Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 56: Downloading Firmware

    New firmware versions of the CP If a new firmware version is available for the module, you will find this on the Internet pages of Siemens Industry Online Support under the following entry ID: 51297224 (http://support.automation.siemens.com/WW/view/en/51297224) On the Internet page, select the "Entry list" tab and the "Download" entry type. There you will find the available firmware files.
  • Page 57 3. Press the Enter key. The start page of the Web server opens. 4. Click on the "Download certificate" entry at the top right of the window. The "Certificate" dialog opens. Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 58 4. Select the "Firmware" tab lower down in the window. 5. Browse for the firmware file on your PC using the "Browse..." button and download the file to the station using the "Run update" button. CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 59: Module Replacement

    CP without needing to download the project data to the station again. When the station starts up again, the new CP reads the project data from the CPU. Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 60 Diagnostics and upkeep 6.3 Module replacement CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 61: Technical Specifications

    Technical specifications Technical specifications of the CP 1243-1 PCC Table 7- 1 Technical specifications of the CP Technical specifications Article number 6GK7 243-1HX30-0XE0 Attachment to Industrial Ethernet Quantity Design RJ-45 jack Properties 100BASE-TX, IEEE 802.3-2005, half duplex/full duplex, autocrossover, autonego-...
  • Page 62: Pinout Of The Ethernet Interface

    Table 7- 2 Pin assignment of the Ethernet interface View of the RJ-45 jack Signal name Assignment Transmit data + TD_N Transmit data - Receive data + Ground Ground RD_N Receive data - Ground Ground CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 63: Approvals

    Approvals Current approvals on the Internet You will also find the current approvals for the product on the Internet pages of Siemens Industry Online Support under the following entry ID: 51297224 (http://support.automation.siemens.com/WW/view/en/51297224) → "Entry list" tab, entry type "Certificates" Other approvals SIMATIC NET products are regularly submitted to the relevant authorities and approval centers for approvals relating to specific markets and applications.
  • Page 64 D-90327 Nürnberg Germany You will find the EC Declaration of Conformity for this product on the Internet at the following address: 51297224 (http://support.automation.siemens.com/WW/view/en/51297224) → "Entry List" Filter settings: Entry type: "Certificates" Certificate Type: "Declaration of Conformity" Search items(s): <name of the module>...
  • Page 65 ● Measures must be taken to prevent the rated voltage being exceeded by more than 40% due to transient disturbances. Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 66 The CP meets the requirements of the AS/NZS 2064 standards (Class A) EAC (Eurasian Conformity) Customs union of Russia, Belarus and Kazakhstan Declaration of the conformity according to the technical regulations of the customs union (TR CU) CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 67: Dimension Drawings

    Dimension drawings Note All dimensions in the drawings of the CP are in millimeters. Figure B-1 Front view and side view left Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 68 Dimension drawings Figure B-2 From above CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 69: Documentation References

    Documentation references Where to find Siemens documentation ● You will find the article numbers for the Siemens products of relevance here in the following catalogs: – SIMATIC NET Industrial Communication / Industrial Identification, catalog IK PI – SIMATIC Products for Totally Integrated Automation and Micro Automation, catalog...
  • Page 70 Documentation references SIMATIC NET Industrial Ethernet Security Basics and Application configuration manual Siemens AG Entry ID: 18701555 (http://support.automation.siemens.com/WW/view/en/18701555) CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 71: Index

    Plant Cloud Services, 55 Priority of the read jobs, 35 Process image, 36 Glossary, 5 Product name, 4 PUT/GET, 13 Hardware product version, 3 Read jobs, 35 Replacing a module, 59 Siemens Automation CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...
  • Page 72 SNMP, 12, 41 Status IDs - data points, 38 STEP 7 information system, 29 STEP 7 version, 15 Threshold value trigger, 52 Time stamp, 34 Time-of-day synchronization, 11 Training, 6 Write jobs, 35 CP 1243-1 PCC Operating Instructions, 02/2015, C79000-G8976-C384-01...

This manual is also suitable for:

Simatic s7-1200

Comments to this Manuals

Symbols: 0
Latest comments: