Installing The Hardware; Mounting The S7999B And Power Supply; Installing The Universal Digital Control Hardware; Quick Setup - Honeywell S7999B Manual

S7999B SYSTEM DISPLAY

INSTALLING THE HARDWARE

Mounting the S7999B and Power Supply

The S7999B can be mounted on the door panel of an
electrical enclosure.
1. Select the location on the door panel to mount the unit;
note that the device will extend into the enclosure at
least one inch past the mounting surface.
2. Provide an opening in the panel door 8-1/8 in. wide by
5-7/8 in. high.
3. Place the S7999B in the opening and use it as a
template to mark the location of the four mounting screw
holes. Remove the device and drill pilot holes at the
marked location.
4. Using the pilot holes as guides, drill 1/4 in. holes
through the door panel.
5. Place the S7999B in the opening, aligning the mounting
holes in the device with the drilled holes in the panel.
6. Secure the S7999B to the panel with four #6-32 screws
and nuts provided.
7. Select a location inside the enclosure for mounting the
power supply.
8. Using the power supply as a template, mark the
locations of two mounting holes in the enclosure.
9. Remove the power supply and drill pilot holes.
10. Drill 1/4 in.holes through the panel at the marked
locations and secure the power supply with the two
#6-32 screws and nuts provided.
11. Remove the 9-pin connector plug from the back of the
S7999B.
12. Wire the connector to the power supply and the RS-485
cables using the wiring diagram in Fig. 14.
13. Insert the 9-pin connector plug back into the S7999B
and secure firmly.
Installing the ControLinks™ and Burner
Control Hardware
Use the following ControLinks™ instructions to install the
system hardware: See Fig. 3 for wiring block diagram.
— 65-0238 R7999 ControLinks™ Control Controller.
— 65-0239 ML7999 ControLinks™ Control Actuator.
— 65-0240 Q7999 Wiring Subbase.
— 65-0101 S7830 Expanded Annunciator.
— 65-0249 S7810M Modbus™ Module.
— 65-0084 Q7800 Wiring Subbase.
— 65-0109 R78xx Flame Amplifier
— 65-0089 ST7800 Purge Card
— 65-0090 S7800 KDM
— 65-0288 S7800A1142 KDM
— 65-1085 7800 SERIES Relay Modules
65-0283—2
Installing the Universal Digital Control
Hardware
Use the following documents to install the UDC2500,
UDC3200, and UDC3500 hardware.
— 51-52-25-124 UDC2500 Quick Start Guide.
— 51-52-03-36 UDC2500 Specification.
— 51-52-25-127 UDC2500 Product Manual.
— 51-52-25-129 UDC3200 Quick Start Guide.
— 51-52-03-39 UDC3200 Specification.
— 51-52-25-119 UDC3200 Product Manual.
— 51-52-25-130 UDC3500 Quick Start Guide.
— 51-52-03-40 UDC3500 Specification.
— 51-52-25-120 UDC3500 Product Manual.
Refer to addendums at the end of this document for
configuration parameters specifically designed for the
application that the UDC controller provides.

QUICK SETUP

1. Make sure the S7999B 9-pin connector is properly
aligned and pressed firmly in place.
2. Make sure the 3-pin connector is connected securely to
the ControLinks™ controller RS-485 communication port.
3. Make sure the S7810M Modbus™ wiring is correct.
WARNING
Electrical Shock Hazard.
Can cause severe injury, death or equipment
damage.
Line voltage is present at the 120 Vac power supply.
4. Make sure the +12 Vdc power supply is connected
securely to the 120 Vac power source.
16