Table Of Contents - IntesisBox ME-AC-KNX-1i User Manual

KNX - Mitsubishi Electric A.C.
®
IntesisBox
INDEX
1. Presentation .................................................................................................... 6
2. Connection ...................................................................................................... 7
3. Configuration and setup .................................................................................... 8
4. ETS Parameters ............................................................................................... 9
4.1 General dialog ............................................................................................ 10
4.1.1 Send READs for Control_ objects on bus recovery ..................................... 10
4.1.2 Scene to load on bus recovery / startup ................................................... 10
4.1.3 Disallow control from remote controller .................................................... 10
4.1.4 Enable func "Control_ Lock Control Obj" ................................................... 11
4.1.5 Enable func "Operating Hours Counter" .................................................... 11
4.1.6 Enable object "Error Code [2byte]" .......................................................... 12
4.1.7 Enable object "Error Text Code [14byte]" ................................................. 12
4.2 Mode Configuration dialog ............................................................................ 13
4.2.1 Indoor unit has FAN mode ...................................................................... 13
4.2.2 Enable use of Heat / Cool bit-type obj ...................................................... 13
4.2.3 Enable PID-Compat. Scaling Mode Objects ............................................... 14
4.2.4 Enable use of + / - object for Mode ......................................................... 15
4.2.5 Enable use of bit-type Mode objects (for control) ...................................... 15
4.2.6 Enable use of bit-type Mode objects (for status)........................................ 16
4.2.7 Enable use of Text object for Mode .......................................................... 16
4.2.8 Enable use of Legacy_ object for Mode .................................................... 16
4.3 Special Modes Configuration dialog ................................................................ 17
4.3.1 Enable use of POWER mode .................................................................... 17
4.3.2 Enable use of ECONOMY mode ................................................................ 18
4.3.3 Enable use of ADDITIONAL HEATING mode .............................................. 19
4.3.4 Enable use of ADDITIONAL COOLING mode .............................................. 20
4.4 Fan Speed Configuration dialog ..................................................................... 21
4.4.1 Fan is accessible in Indoor unit ............................................................... 21
4.4.2 Available fanspeeds in Indoor Unit ........................................................... 21
4.4.3 Indoor unit has AUTO fan speed .............................................................. 22
4.4.4 DPT object type for fanspeed .................................................................. 22
4.4.5 Enable use of +/- object for Fan Speed .................................................... 23
4.4.6 Enable "Fan Speed Manual/Auto" objects (for Control and Status) ............... 24
4.4.7 Enable use of bit-type Fan Speed objects (for Control) ............................... 24
4.4.8 Enable use of bit-type Fan Speed objects (for Status) ................................ 25
4.4.9 Enable use of Text object for Fan Speed ................................................... 25
4.4.10 Enable use of Legacy_ object for Fan Speed ............................................. 26
4.5 Vanes Up-Down Configuration dialog ............................................................. 26
4.5.1 Indoor unit has U-D Vanes ..................................................................... 26
4.5.2 Available positions in Indoor Unit ............................................................ 27
4.5.3 Indoor unit has AUTO Vanes U-D ............................................................ 27
4.5.4 DPT object type for Vanes Up-Down ........................................................ 27
4.5.5 Enable use of +/- object for Vanes U-D .................................................... 28
4.5.6 Enable use of bit-type Vane U-D objects (for Control) ................................ 29
4.5.7 Enable use of bit-type Vane U-D objects (for Status) ................................. 30
4.5.8 Enable "Vanes U-D Man/Auto" objects (for Control and Status) ................... 30
4.5.9 Enable "Vanes U-D Swing" objects (for Control and Status) ........................ 31
4.5.10 Enable use of Text object for Vane U-D .................................................... 31
4.5.11 Enable use of Legacy_ object for Vanes ................................................... 32
4.6 Temperature Configuration dialog.................................................................. 32
4.6.1 Periodic sending of "Status_ AC Setp" ...................................................... 32
4.6.2 Transmission of "Status_ AC Return Temp" .............................................. 33
4.6.3 Enable use of +/- object for Setpoint Temp .............................................. 33
© Intesis Software S.L.U. - All rights reserved
This information is subject to change without notice
®
IntesisBox is a registered trademark of Intesis Software SLU
User's manual r2.3 eng
URL http://www.intesisbox.com
Email info@intesisbox.com
tel +34 938047134
4 / 63