SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference.
Put the cutlery in the cutlery basket with the sharp ends • pointing down or put them in the cutlery drawer in a horizontal position with the sharp edges down. Do not leave the appliance with the open door unattended to •...
Page 4
• Do not remove the dishes from the appliance until the programme is complete. Some detergent may remain on the dishes. • The appliance can release hot steam if you open the door while a programme operates. • Do not put flammable products or items that are wet with flammable products in, near or on the appliance.
CONTROL PANEL On/off button Delay button Display Programme buttons Indicators INDICATORS Indicator Description XtraDry indicator. Rinse aid indicator. It is always off while the programme operates. Salt indicator. It is always off while the programme operates.
PROGRAMMES Consumption values Degree of soil Programme Programme phases Type of load Duration Energy Water (min) (kWh) Normal soil • Pre-wash 1.039 Crockery and • Wash 50 °C cutlery • Rinses • • Pre-wash 45 - 156 0.7 - 1.4 7 - 12 Crockery, cut- •...
Page 7
CANCEL FUNCTION ADJUSTING THE WATER SOFTENER Use CANCEL to: Make sure that the appliance is in user mode: • CANCEL the currently running programme. 1. Press • Stop the countdown of the Delay option. • The indicators are off. • Bring the appliance back to the programme selection mode.
• The indicator flashes. While the drying phase operates, the • The display shows the current setting: device opens the appliance door. The door is then kept ajar. – = rinse aid empty notification activated. By default, AirDry is activated with all programmes –...
ADDING SALT Before the first use, put one litre of water in the salt container. CAUTION! Water and salt can come out of the salt container during filling. To prevent corrosion, start a programme immediately after filling the salt container. ADDING RINSE AID The rinse aid helps to dry the dishes without streaks and stains.
Page 10
ADDING DETERGENT If the programme has a prewash phase, put a small quantity of detergent also in compartment B. ADDING MULTI-TABLETS • Adjust the water softener to the lowest level. THE AUTO OFF FUNCTION STARTING A PROGRAMME This function decreases energy consumption by 1.
4. Set the applicable options. closing the door, the appliance continues from the 5. Close the appliance door to start the point of interruption. programme. If the door is opened during the drying XTRADRY OPTION phase, before AirDry automatically opens it, the programme ends after 30 Activate this option when you want to boost the seconds.
(powder, gel, tablets containing no additional • Make soft the remaining burned food on the agents), rinse aid and salt separately for optimal items. cleaning and drying results. • Put hollow items (cups, glasses and pans) with • At least once a month run the appliance with the the opening down.
CLEANING THE FILTERS • Make sure that there are no residues of food or soil in or around the edge of the sump. • Put back in place the flat filter (C). Make sure that it is correctly positioned under the 2 guides. •...
Page 14
The majority of problems that can occur can be solved without the need to contact an Authorised Service Centre. Problem and alarm code Possible cause and solution You cannot activate the appli- • Make sure that the mains plug is connected to the mains sock- ance.
Problem and alarm code Possible cause and solution The appliance trips the circuit- • The amperage is insufficient to supply simultaneously all the ap- beaker. pliances in use. Check the socket amperage and the capacity of the meter or turn off one of the appliances in use. •...
Problem Possible cause and solution The interior of the appliance is • This is not a defect of the appliance. it is caused by the hu- wet. midity in the air that condenses on the walls. Unusual foam during washing. •...
Capacity Place settings Power consumption Left-on mode (W) Power consumption Off-mode (W) 0.50 1) Refer to the rating plate for other values. 2) If the hot water comes from alternative source of energy, (e.g. solar panels, aeolian energy), use the hot water supply to decrease energy consumption.