Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for TorcUP ULTRA series
Summary of Contents for TorcUP ULTRA series
-
Page 2: Placing Tool In Service
NOTICE or leaks in the hoses. The use of other than genuine TorcUP replacement parts may result in safety hazards, decreased tool performance, and increased maintenance, and may invalidate all warranties. Repairs should be made only by authorized personnel. Consult your nearest TorcUP Authorized Service Center. -
Page 3: Connecting The Tool
*Use accessories recommended by TorcUP. *Always use retaining pin and ring to engage the socket *Use only impact sockets and accessories. Do not use hand to the square drive. -
Page 4: Operating The Wrench
PLACING THE TOOL IN SERVICE When decreasing pressure, always lower the pressure WRENCH POSITIONS below the desired point and then bring the gauge back up Square Drive Position for Loosening and to the desired pressure. Tightening (Dwg. 02) 4. When the desired pressure is reached, retighten the wing nut and cycle the tool again to confirm that the desired pressure setting has been obtained. - Page 5 PLACING THE TOOL IN SERVICE LUBRICATION Marine Moly Grease Lubrication frequency is dependent on factors known only to the user. The amount of contaminants in the work area is one factor. Tools used in a clean room environment will obviously require less service than a tool used out-doors and dropped in loose dirt or sand.
- Page 6 UT Series Torque Conversion Chart P.S.I./FT./lbs Bar/N.M. UT-2 UT-3 UT-7 UT-11 UT-2 UT-3 UT-7 UT-11 P.S.I. ft./lbs. ft./lbs. ft./lbs. ft./lbs. N.m. N.m. N.m. N.m. 1,000 1,090 1,003 1,478 1,200 1,308 1,204 1,773 1,400 1,036 1,526 1,404 2,069 1,600 1,185 1,745 1,606 2,366 1,800...
- Page 7 - 6 -...
- Page 8 Part Numbers for Ordering Part UT-2 UT-3 UT-7 UT-11 Housing UT-2-01 UT-3-01 UT-7-01 UT-11-01 Housing Threaded Plug TU-7-39 UT-11-39 Reaction Arm TU-2-03-1 TU-3-03-1 TU-7-03-1 TU-11-03-1 Reaction Arm Cover TU-2-03-7 TU-3-03-7 TU-7-03-7 TU-11-03-7 Cover Screws TU-2-03-8 TU-3-03-8 TU-7-03-8 TU-11-03-8 Reaction Arm Spring TU-2-03-6 TU-3-03-6 TU-7-03-6...
-
Page 9: General Instructions
Maintenance Section WARNING 3/4” wrench, unscrew and remove the two Swivel Inlets (33) with their attached Couplers (34). Always turn off the power supply, bleed off hydraulic fluid from the hose connections on the cylinder 3. Remove the Housing from the vise jaws and with the assembly and disconnect the hoses before attempting inlet openings over a container to catch the oil, drain as to repair or perform maintenance on this tool. - Page 10 NOTICE The Cylinder Gland is staked into the Housing to the surface of the part and help prevent distortion. This is prevent it from loosening due to vibration or particularly true of threaded members and housings. turbulence in the hydraulic oil flow. The stake point 3.
- Page 11 NOTICE In the following step, the Cylinder Gland must be Housing, rotation will be clockwise to tighten. A staked into the Housing to prevent it from loosening right side extension is counterclockwise for loosening. due to vibration or turbulence in the hydraulic oil flow.
-
Page 12: Troubleshooting Guide
Troubleshooting Guide Trouble Probable Cause Solution Couplers are not securely Check the Coupler connections and attached to the tool or pump make certain that they are connected. Coupler is defective Replace any defective Coupler. Piston will not advance or retract Replace the switch and/or control Defective remote control switch pendent...
Need help?
Do you have a question about the ULTRA series and is the answer not in the manual?
Questions and answers