Connecting Water Supply; Appropriate Installation Location; Removing Packaging Reinforcement; Connecting To The Drain - Beko WTV 6502 B0S User Manual

2 Installation
Refer to the nearest Authorised Service Agent for installation
of the product. To make the product ready for use, review
the information in the user manual and make sure that the
electricity, tap water supply and water drainage systems are
appropriate before calling the Authorized Service Agent. If
they are not, call a qualified technician and plumber to have
any necessary arrangements carried out.
C
Preparation of the location and electrical, tap water and
waste water installations at the place of installation is
under customer's responsibility.
Make sure that the water inlet and discharge hoses
as well as the power cable are not folded, pinched or
crushed while pushing the product into its place after
installation or cleaning procedures.
B
:
Installation and electrical connections of
warning
the product must be carried out by the Authorized
Service Agent. Manufacturer shall not be held liable for
damages that may arise from procedures carried out by
unauthorized persons.
A
:
Prior to installation, visually check if the product
warning
has any defects on it. If so, do not have it installed.
Damaged products cause risks for your safety.

2.1 Appropriate installation location

• Place the machine on a rigid floor. Do not place it on a
long pile rug or similar surfaces.
• Total weight of the washing machine and the dryer -with
full load- when they are placed on top of each other
reaches to approx. 180 kilograms. Place the product
on a solid and flat floor that has sufficient load carrying
capacity!
• Do not place the product on the power cable.
• Do not install the product at places where temperature
may fall below 0ºC.
• Place the product at least 1 cm away from the edges of
other furniture.

2.2 Removing packaging reinforcement

Tilt the machine backwards to remove the packaging
reinforcement. Remove the packaging reinforcement by
pulling the ribbon.

2.3 Removing the transportation locks

A
:
Do not remove the transportation locks before
warning
taking out the packaging reinforcement.
:
Remove the transportation safety bolts before
warning
operating the washing machine! Otherwise, the product
will be damaged.
6 / EN
1. Loosen all the bolts with a suitable spanner until they
rotate freely (C) .
2. Remove transportation safety bolts by turning them
gently.
3. Attach the plastic covers supplied in the User Manual bag
into the holes on the rear panel. (P)
C
Keep the transportation safety bolts in a safe place to
reuse when the washing machine needs to be moved
again in the future.
Never move the product without the transportation safety
bolts properly fixed in place!

2.4 Connecting water supply

C
The water supply pressure required to run the product is
between 1 to 10 bars (0.1 – 1 MPa). It is necessary to
have 10 – 80 liters of water flowing from the fully open
tap in one minute to have your machine run smoothly.
Attach a pressure reducing valve if water pressure is
higher.
A
:
Models with a single water inlet should not be
warning
connected to the hot water tap. In such a case the laundry
will get damaged or the product will switch to protection
mode and will not operate.
:
Do not use old or used water inlet hoses on the
warning
new product. It may cause stains on your laundry.
Tighten all hose nuts by hand. Never use a tool when
tightening the nuts.
Open the taps completely after making the hose
connection to check for water leaks at the connection
points. If any leaks occur, turn off the tap and remove the
nut. Retighten the nut carefully after checking the seal. To
prevent water leakages and damages caused by them,
keep the taps closed when the machine is not in use.

2.5 Connecting to the drain

• The end of the drain hose must be directly connected to
the wastewater drain or to the washbasin.
A
:
Your house will be flooded if the hose comes
warning
out of its housing during water discharge. Moreover, there
is risk of scalding due to high washing temperatures!
To prevent such situations and to ensure smooth water
intake and discharge of the machine, fix the end of the
discharge hose tightly so that it cannot come out.
• The hose should be attached to a height of at least 40
cm, and 100 cm at most.
• In case the hose is elevated after laying it on the floor
level or close to the ground (less than 40 cm above the
Washing Machine / User's Manual