Related Manuals for Canvas MILLA
Summary of Contents for Canvas MILLA
- Page 1 MILLA ELECTRIC FIREPLACE MODEL NO. 064-3177-0 ASSEMBLY INSTRUCTIONS Toll-free: 1-888-670-6684 IMPORTANT: Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference.
- Page 2 MADE IN CHINA IMPORTED BY TRILEAF DISTRIBUTION TRIFEUIL TORONTO, CANADA M4S 2B8...
- Page 3 Important Safety Information Parts List Installation Operating Instructions Cleaning and Maintenance Troubleshooting Guide Warranty Warning! To reduce the risk of serious injury, read the following safety instructions before assembling and operating this fireplace. This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to part 15 of the FCC rules.
- Page 4 MODEL NO. 064-3177-0 When using electrical appliances, basic precautions should always be followed to reduce the rise of fire, electric shock and injury to persons, including the following: Read all instructions before installing or using the fireplace. DANGER: If the information in this manual is not followed exactly, an electric shock or fire may result causing property damage, personal injury or loss of life.
-
Page 5: Electrical Specifications
• There is a thermostat device provided inside of the unit. If the inner temperature overheats or abnormal heating occurs, the thermostat device will cut off power supply to prevent damage or risk of fire. • DO NOT slide insert on top of wood to avoid scratching wood surface. • DO NOT place any objects on top of insert and top air intake vents as this will cause unit to overheat and can cause a fire. - Page 6 MODEL NO. 064-3177-0 Hardware indicated in brackets ( ) are extra if needed. Safety Mounting Tap - 2 Screw for Mantel - 2 + (1) Fireplace Mantel - 1 Screw for Wall Anchor - 2 + (1) Fireplace Insert - 1 Washer - 4 + (2) Wall Anchor - 2 Remote Control - 1...
- Page 7 The Fireplace can be installed with 2 options: 1. Mount the unit on the wall..Page 8 2. Freestanding..Page 11...
- Page 8 MODEL NO. 064-3177-0 Step 1 Requires 1 Before installing your fireplace, determine the desired location. WARNING: For the best effect install the fireplace out of direct sunlight and away from 6 in. overhead lighting. 15cm 6 in. 15cm 6 in. 15cm Step 2 Requires F...
- Page 9 Step 3 Requires C, E, F Select hardware best suited for your wall type and secure the mounting bracket F to the wall. Warning! Enclosed wall anchors H only can be use on a concrete wall. STUD WALL: DRYWALL: CONCRETE WALL: Secure the mounting Screw wall anchors Drill holes at marked...
- Page 10 MODEL NO. 064-3177-0 Step 5 Requires 1, G, H Use the fireplace as a guide, mark four holes at the bottom of the fireplace 1 as shown. Select hardware best suited for your wall type and secure the fireplace 1 to the wall. Warning! Enclosed wall anchors H only can be use on a concrete wall.
- Page 11 Step 1 Requires 1, A, B, C, D, E Drill two holes into the wall and insert wall anchor E. Then install the safety mounting tape A on top rear of mantel 1 using washer D and screw B. Attach opposing side of the safety mounting tape A using washer D and screw C fastened into wall anchor.
-
Page 12: Mode Button
MODEL NO. 064-3177-0 Power Button • Pressing the power button will turn the unit ON or OFF. • When the unit is in ON mode, the power icon indicator light will glow green. • When the unit is in OFF mode, the power icon indicator light will glow red. If the heater is working when the unit is powered OFF, the fan will continue to run for another 20 seconds to ensure heat will not be trapped inside the unit. -
Page 13: Care And Maintenance
13 13 Timer Setting • The timer mode shoud be used to set the countdown for the unit’s main power. • Press the up arrow button or down arrow button to adjust the timer setting from 0 hour (OFF) to 9 hours with 0.5 hour intervals. -
Page 14: Replacing The Remote Control Battery
MODEL NO. 064-3177-0 MODEL NO. 064-3177-0 WARNING: Make sure the power is turned off before proceeding. Any electrical repairs or rewiring of this unit should be carried out by a licensed electrician in accordance with national and local codes. If repairing or replacing any electrical component or wiring, the original wire routing, colour coding and securing locations must be followed. - Page 15 PROBLEM POSSIBLE CAUSE SOLUTION No power. Check that unit is plugged into a The unit does not Logs do not standard 120 V outlet. Then make sure have power. glow. power is set at “ON” position. E1 displayed Unplug unit, wait 5-10 minutes, then The overheat on control the sensor will reset itself.
- Page 16 MODEL NO. 064-3177-0 This CANVAS product carries a one (1) year warranty against defects in workmanship and materials. Trileaf Distribution agrees to replace the defective product free of charge within the stated warranty period, when returned by the original purchaser with proof of purchase. This product is not guaranteed...