Subscribe to Our Youtube Channel
Related Manuals for Hills Supa Fold 230
Summary of Contents for Hills Supa Fold 230
- Page 1 Supa Fold ® Folding Frame Clothesline Owner’s Manual TO SUIT MODELS: Supa Fold 230 Advantage ® Supa Fold 230 ® Supa Fold 210 ® Supa Fold 190 ® Supa Fold 120 ® Supa Fold 70 ®...
-
Page 2: Consumer Advice
You can remove and hang the product. lid to keep your Hex keys in a safe place! Thank you for choosing Hills. 3. Check all components are in the carton (refer to tables below for your model). Warning... -
Page 3: Pack Contents
Pack Contents Supa Fold 210 Supa Fold 120 / Supa Fold 70 ® ® ® Part name Qty. Part name Qty. Mount Bracket Assembly - LH Mount Bracket Assembly - LH Mount Bracket Assembly - RH Mount Bracket Assembly - RH Arm Assembly - LH Arm Assembly - LH Arm Assembly - RH... -
Page 4: Installation
If wall mounted - ensure area is free from pipes and other obstructions. If post mounted - you will need to purchase the Hills Ground Mount Kit to suit your Supa Fold Clothesline. ® 2. Ensure you have left sufficient space surrounding the Clothesline (Fig. - Page 5 Installation Fig. 2a...
- Page 6 (Fig. 4). Note: If you are replacing an existing Hills Folding Frame product, the mount hole centres may be the same. Therefore your new Supa Fold Folding Frame ®...
- Page 7 Installation Fig. 4 Top of Bracket 50mm User’s Head Height • User’s Head Height = Top of Bracket • Recommended Clearance = User’s Head Height + 50mm Ground Level...
- Page 8 Installation 1. Drill holes in wall. 2. Secure Mount Brackets Installation method Locate mount bracket assembly over holes in wall, insert masonry fasteners and secure A. Masonry fasteners are included with as per diagram below (Fig.6). this product. Note: these fasteners are designed only for installation in sound masonry walls.
- Page 9 Installation Fixing to a Post Kit 1. Install your Post Kit Post Kits for Supa Fold Folding Frame ® Clotheslines are available as optional accessories. Install the Post Kit as per the separate instructions provided with the kit. 2. Remove the Cross Brace During installation of your Post Kit the Cross Brace would have been fitted across the vertical posts.
- Page 10 Assembly 1. Fit Arms to Mount Brackets (Fig.9) A. Fit arm assembly to Mount Bracket Assembly, ensuring Arm and Strut Ends engage with the Pivots. Ensure Line Tie- Offs are facing inwards. B. Secure arms using Bayonet Caps Note: the larger Bayonet Cap is used to secure the Arm End and the smaller Bayonet Cap is used to secure the Strut End.
- Page 12 3. Assemble Corners into Spreader Bar A. Insert Corners into both ends of Spreader Bar, ensure the orientation of the corners and handle match. B. To secure the Corners, remove the Corner Caps. C. Tighten M6 socket head bolt using 5mm Hex Key.
- Page 13 4. Assemble Spreader Bar to Arms A. Raise both Arms to the ‘horizontal’ position (refer to Operation section, page 17). B. Insert the Corners into Arm Ends. C. Ensure the Handle moulding is the correct way-up (Fig.12). D. Secure both Corners by tightening M6 socket head bolt using 5mm hex key (Fig.13).
- Page 14 Assembly 5. Re-Attach Outer Cover Mouldings A. Locate the pins on Outer Cover mouldings with the keyed slots in the Mount Bracket and slide down to secure. Fig. 15...
- Page 15 Line Assembly To Attach Line Segments Step 1 Step 2 Your individual line segments are supplied partially Add one Cover Cap to each line segment in the sub-assembled like this. orientation as shown. Step 3 Step 4 Ensure the Cover Cap, Line, Spring and Retainer are Attach this end of the Line assembly to a Tie-Off on assembled like this.
- Page 16 Note: A short video showing the attachment of line We reccommend trimming excess line after a few segments is available for viewing on the Hills website: loads of washing have been hung to allow ‘pre- www.hills.com.au stretch’ of line to occur.
-
Page 17: Operation
Operation To Raise the Clothesline (Fig.16) To Lower the Clothesline (Fig.17) A. Loosely grip the Spreader Bar Handle. A. Loosely grip the Spreader Bar Handle. B. Pull the frame away from the wall slowly B. Raise the frame until you hear both and raise above your head until you hear struts ‘click’... -
Page 18: Handy Hints
Ensure way outwards for larger items. fasteners are secure. If there is any damage, parts should be replaced with original Hills When hanging thick or bulky items, you may spares. The Clothesline should be repaired remove one piece of line to give yourself before using again. - Page 19 Unless any addition or attachment to this the part free of cost for a period of TEN product has Hills specific approval or is sold (10) years from date of purchase of the as a Hills Supa Fold product the warranty ®...
- Page 20 Hills Industries Limited A.B.N. 35 007 573 417...
Need help?
Do you have a question about the Supa Fold 230 and is the answer not in the manual?
Questions and answers