Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for V-ZUG GK11TGA
Summary of Contents for V-ZUG GK11TGA
- Page 1 V-ZUG Ltd GK11TG, GK51TPG Operating instructions E-Nr GK11TGA E-Nr GK51TPGA...
-
Page 2: Table Of Contents
Table of contents Ú [ e s ] I n s t r u c c i o n e s d e u s o y m o n t a j e Changing the nozzles of the rapid, semi-rapid and auxiliary Safety considerations.............. -
Page 3: Installation
given supervision or instruction concerning use of the Note: To avoid jeopardising the electrical safety of the appliance by a person responsible for their safety. appliance, it is forbidden to use high-pressure or steam jet cleaning devices. Make sure you keep these instructions for use and assembly in a safe place, so that you can hand them on with the appliance SHOULD THE RELEVANT CONDITIONS NOT BE PROPERLY if it ever changes owner. -
Page 4: Clearances
Before connecting the unit, check whether the local connection The shield must be at least 10 mm from the lowest part of the conditions (type of gas) are compatible with the unit’s setting. hotplate and must be capable of withstanding the appliance Observe any special conditions imposed by local suppliers temperatures. -
Page 5: Connection
Turn the clips and tighten them fully. Fit regulator (N.G.) or a test point (Propane gas) directly to the R 1/2’’ connection. The position of the clips depends on how thick the work surface is. Direction of gas flow is indicated on the rear of the regulator. For position of the inlet connection refer Preparing to install: Use pipe compound or thread sealant, properly theaded pipes and careful assembly procedure so that there is no cross... -
Page 6: Changing The Nozzles Of The Rapid, Semi-Rapid And Auxiliary Burners On The Cooktop
Request change-over injectors from our customer service Use the disassembly lever 483196 available from our Service deparment (refer injector chart below for sizes). Centre. To release the front clips, apply the lever in the area shown in figures below according to the cooktop model. Natural Gas Propane Gas Burner... -
Page 7: Adjustment Of The Taps
appliance's interior from liquids and dirt, which might otherwise prevent its correct operation. Adjust the minimum ring setting by turning the by-pass screw using a flat head screwdriver. To adjust the minimum flame for N.G. replace the control knob onto the spindle, light the gas and turn the control knob to the small flame position. -
Page 8: Accessories
Accessories The following accessories can be purchased from the Switching on automatically Technical Assistance Service: If your hob can be switched on automatically (ignition sparkers): Additional wok pan support Press the chosen burner control knob and turn it Only for use on double and anticlockwise to the maximum power setting. -
Page 9: Cooking Pans
For dual double-flame burners, the inner and outer flames can Cooking recommendation be controlled separately. The available power levels are as follows: Burner Very high - High Medium Inner and outer flame on full Wok burner Boiling, steam- Reheating and keeping power. -
Page 10: Cleaning And Maintenance
Clean the burners and pan supports using soapy water and Do not cook without using a lid scrub with a non-wire brush. and make sure the lid is properly fitted. This wastes Alternatively, the pan supports can be put in the dishwasher. energy. -
Page 11: Wiring Diagram
Fault Possible cause Solution The kitchen smells of gas. A gas tap has been left on. Turn off the taps. Incorrect coupling of gas cylinder. Check that the coupling is sound. Possible gas leak. Shut off the gas supply, ventilate the premises and immediately notify an authorised installation techni- cian to check and certify the installation. - Page 12 ©V-ZUG Ltd, CH-6301 Zug 2012 V-ZUG Ltd Industriestrasse 66, CH 6301 Zug vzug@vzug.ch, www.vzug.com *9000899997* Cod. 9000899997 (A) J302.360-0...