Notes - Philips TPN15.2E LA Service Manual

Picture mode Screen size
Warm (6500K) 43PUH4900/88 128
43PUT4900/12 127
43PUK4900/12 126
43PUT4900/60 127
49PUH4900/88 128
49PUT4900/12 126
49PUK4900/12 128
49PUT4900/60 127
55PUH4900/88 127
55PUT4900/12 127
55PUK4900/12 125
55PUT4900/60 126
This group setting of colour temperature will be applied
automatically to the TV / VGA / HDMI / AV sources.
6.4 Option Settings
6.4.1 Introduction
The microprocessor communicates with a large number of I
ICs in the set. To ensure good communication and to make
digital diagnosis possible, the microprocessor has to know
which ICs to address. The presence / absence of these
NT72567 ICs is made known by the option codes.

Notes:

• After changing the option(s), save them by pressing the OK
button on the RC before the cursor is moved to the left,
select STORE and press OK on the RC.
• The new option setting is only active after the TV is
switched "off" / "stand-by" and "on" again with the mains
switch (the NVM is then read again).
6.4.2 Option Code Overview
Enter SAM mode to check the option codes. they could not be
edited in the NVM.
6.4.3 Display Code Overview
Press the following key sequence on a standard RC
transmitter: "062598" directly followed by MENU and "xxx",
where "xxx" is a 3 digit decimal value of the panel type: see
column "Display Code" in
Code, restart the set immediately.
Table 6-3 Display code overview
CTN_ALT BOM# Panel Type
43PUH4900/88 TPT430U3-EQYSHM.G S1C NH
43PUT4900/12 TPT430U3-EQYSHM.G S1C NH
43PUK4900/12 TPT430U3-EQYSHM.G S1C NH
43PUT4900/60 TPT430U3-EQYSHM.G S1C NH
49PUH4900/88 TPT490U2-EQYSHM.G SC1C XM
49PUT4900/12 TPT490U2-EQYSHM.G SC1C XM
49PUK4900/12 TPT490U2-EQYSHM.G SC1C XM
49PUT4900/60 TPT490U2-EQYSHM.G SC1C XM
55PUH4900/88 TPT550U2-EQYSHM.G S1E XM
55PUT4900/12 TPT550U2-EQYSHM.G S1E XM
55PUK4900/12 TPT550U2-EQYSHM.G S1E XM
55PUT4900/60 TPT550U2-EQYSHM.G S1E XM
6.5 Reset of Repaired SSB
A very important issue towards a repaired SSB from a Service
repair shop (SSB repair on component level) implies the reset
of the NVM on the SSB.
A repaired SSB in Service should get the service Set type
"00PF0000000000" and Production code "00000000000000".
Colour temperature
Red Green Blue
107 84
106 85
108 86
106 85
102 73
101 72
100 75
100 75
121 120
120 119
122 120
121 118
Table 6-3. After resetting the Display
Display Code
005
005
005
005
004
004
004
004
002
002
002
002
Alignments
Also the virgin bit is to be set. To set all this, you can use the
ComPair tool or use the "NVM editor" and "Dealer options"
items in SAM (do not forget to "store").
After a repaired SSB has been mounted in the set (set repair
on board level), the type number (CTN) and production code of
the TV has to be set according to the type plate of the set. For
this, you can use the NVM editor in SAM. The loading of the
CTN and production code can also be done via ComPair
(Model number programming).
In case of a display replacement, reset the "Operation hours
display" to "0", or to the operation hours of the replacement
display.
Remark:
- After the NVM has been replaced, go to SAM and scroll to the
<Reload MAC address> (see figure 1*).
- Select the item and press <OK> on the RC.
6.5.1 Reset of Repaired SSB
Instruction
2
C After NVM replacement, reload MAC address via SAM
menu.This ensures the correct MAC address to be available in
CSM for future repair actions.
Way of working:
• After the NVM has been replaced, go to SAM and scroll to
the <Reload MAC address> .
• Select the item and press <OK> on the RC.
Notes:
• Only applicable to all related models that are "Smart TV
level 0"enabled (only YouTube access). For models
without internet connection feature, no action is needed.
• HDCP keys are located in the NVM. If you are loading NVM
with the ComPair tool, there is warning message displayed.
New NVM EEPROMs are shipped with pre-loaded HDCP keys.
6.5.2 SSB Identification
SSB's of this chassis are identified by a "715" code on the SSB.
715Axxxx-Nnn-MMM-OOOO
• 715 main category, Printed Wiring Board
• Axxxx sub category, sequential coding number
• Nnn Version code
• N Development number
• nn Production number
• MMM Mounting variation code
• OOOO Optional variation code
Make sure when replacing an SSB the SSB identification codes
match the replacement panel.
back to
div. table
TPN15.2E LA 6. EN 23
2015-Nov-27