Philips TPN15.2E LA Service Manual page 16

EN 16 5. TPN15.2E LA
How to Exit SAM
Use one of the following methods:
• Switch the set to STANDBY by pressing the mains button
on the remote control transmitter or the television set.
• Via a standard RC-transmitter, key in "00" sequence.
Note: When the TV is switched "off" by a power interrupt while
in SAM, the TV will show up in "normal operation mode" as
soon as the power is supplied again. The error buffer will not be
cleared.
5.2.4 Contents of the Factory mode:
Purpose
• To perform extended alignments.
Specifications
• Displaying and or changing Panel ID information.
Table 5-2 Factory mode overview
Item Item value
0 F/W VERSION
1 Board ID
2 PANEL_ID
3 DB COPY TV to USB
4 DB READ USB to TV
5 CLR_TEMP_R
6 CLR_TEMP_G
7 CLR_TEMP_B
8 AUTO_COLOR
9 ADC_GAIN_R
10 ADC_GAIN_G
11 ADC_GAIN_B
12 ADC_OFFSET_R
13 ADC_OFFSET_G
14 ADC_OFFSET_B
15 VIRGING_MODE
16 E_Fuse
17 ORT_MODE
18 AGEING MODE
19 AUD_LIMITE_MODE
20 AUD_THRESHOLD_BYTE1
21 AUD_THRESHOLD_BYTE2
22 AUD_THRESHOLD_BYTE3
23 AUD_GAIN_LINEIN
24 AUD_GAIN_HDMI
25 AUD_GAIN_ATV
26 AUD_GAIN_DTV
27 AUD_GAIN_USB
28 TUNER_ID
29 CIPLUS QUERY
30 CIPLUS UPDATE
31 CI Key Type Selection
32 AQ_TABLE_INDEX
33 EDID UPDATE
34 Vx1 SSC Ratio
35 Vx1 SSC Freq
36 DDR MIU0 SSC Ratio
37 DDR MIU0 SSC Freq
38 DDR MIU1 SSC Ratio
39 DDR MIU1 SSC Freq
40 Panel H.Flip
41 Panel V.Flip
42 Panel ABSwap
43 Watchdog
44 Backlight PWM freq.(Hz)
45 Backlight PWM Limit
46 VGA_TxRx_Mode
47 LVDS Driving
2015-Nov-27
Service Modes and Fault Finding
Default value
43" 49" 55"
Press OK
715G6079-3in1
5 4 2
Press OK
Press OK
115 128 73
114 128 89
128 128 128
Press OK
0
0
0
0
0
0
off
on
off
off
1
100
200
100
-9 -10 0
-10 -10 0
-10 -10 10
-10 -10 10
0
0
Press OK
Press OK
ProductKey
1 2 1
Press OK
0.4%
30KHz 30KHz off SSC
2% 2% 0%
30KHz 30KHz off SSC
2% 2% 0%
30KHz 30KHz off SSC
off off off
off off off
off off off
5sec 5sec off
150 150 150
2 2 20
off off off
3 3 1
• Displaying and or changing Tuner ID information.
• Error buffer clearing.
• Various software alignment settings.
• Testpattern displaying.
• Public Broadcasting Service password Reset.
• etc.
How to Activate the Factory mode
To activate the Factory mode, use the following method:
• Press the following key sequence on the remote control
transmitter: from the "menu/home" press "1999", directly
followed by the "Back/Return" button. Do not allow the
display to time out between entries while keying the
sequence.
After entering the Factory mode, the following items are
displayed,
Description
Displays the software versions of the supplier, Flash PQ, Smart Picture, BL Dimming,
Source Meter, the Picture Quality checksum, the Dimming library, the Source meter library, the
Flash AQ, MCU and OAD software versions.
Dispaly the Board ID; be careful changing this, it can result in not correct displaying the screen!
Displays and changes the Panel ID with the left and right cursor; be careful changing this, it can
result in not correct displaying the screen!
DB COPY TV to USB
DB READ USB to TV
Red colour temperature setting
Green colour temperature setting
Blue colour temperature setting
PC: any pattern that has black and white, YPbPr: SMPTE bar (colour bar), any timing.
Red ADC gain
Green ADC gain
Blue ADC gain
Red ADC offset
Green ADC offset
Blue ADC offset
Use this to return the set to virgin mode. Depends whether the set has been used already.
E-fuse mode
ORT mode
Use this for aging a new LCD panel
Three modes,0: off, 1: adaptive mode, 2: fixed mode
Limit threshold
Limit threshold
Limit threshold
Line-in audio gain
HDMI audio gain
Analogue TV audio gain
Digital TV audio gain
USB audio gain
Displays and changes the Tuner ID with the left and right cursor. Not to be changed when the
tuner is replaced with the correct service part.
Shows the Validity of the CI+ key and the supplier information
Used to enter a new CI+ code into the NVM. This can only be used when no CI+ code exists in
the NVM
CI Key Type Selection
Audio Quality index
Used to enter a new EDID codes into the NVM
LVDS SSC ratio
LVDS SSC frequency
DDR MIU0 SSC ratio
DDR MIU0 SSC frequency
DDR MIU1 SSC ratio
DDR MIU1 SSC frequency
Flip panel
Flip panel
ABSwap panel
Watchdog
Backlight PWM frequency
Backlight PWM Limit
VGA_TxRx_Mode
LVDS Driving
back to
div. table