Barco R9801323 Installation Manual

1
Get t i n g st ar ted
This installation guide describes how to install the air inlet filter and exhaust air kits. For more information, including technical specifications
or product specifications, visit the product website at www.barco.com or read your projector user manual.
Note! The exhaust air kit is an accessory for Barco F50- and CT- series projectors only.
Inst a l l ati on G u id el i n e s
• The exhaust kit must only be used with ceiling mounted projectors.
• The air filter kit is sold separately.
• The exhaust air kit and air inlet filter can be installed separately of one another.
• If the exhaust is to be directed into a false ceiling, this area must be well-ventilated. However, attention must be paid to ensure that the
ventilation does not override the projector's internal fans.
• Minimum safety distance between the projector (with kit mounted) and the ceiling is at least 15 cm (5.9").
• Do not try to force parts into position; if there is resistance, remove the part, reposition and try again.
• Do not overtighten screws.
• Do not block the air inlet or the exhaust air outlet.
• Hot air is exhausted from the rear air outlet. Do not place any heat-sensitive objects in the vicinity of the exhaust vent.
Note! The exhaust air kit is only intended for use with ceiling mounted projectors
3
I n st a l lati on
must be
≥90
1. Verify installation requirements. 2. Install air inlet filter (optional).
Verify that the installation area meets Position the air inlet filter onto the projector grill,
the relevant technical and environmental making sure that the plastic guide on the filter
requirements, as illustrated above. enters the grill properly. Install the filter with a
M3x8 screw at the right side (reference 1) and two
M3x14 screws at the left side (reference 2).
F50- & CT- Series Exhaust Air Kit & Air Filter Kit
Installation Guide
1
2
1 3
4
3. Install duct to ceiling cover.
Loosen the two ceiling mount fastening screws
(reference 3 and 4). Remove the center rib.
Slide the duct into the ceiling mount tracks
as illustrated. Make sure that the side of the
duct clicks into position, as shown in the detail
illustration. Install the rib side screws (reference
Note! Successful installation of the air inlet
5). Replace and fasten the two ceiling mount
filter will trigger automatic changes in the
screws (reference 3 and 4).
projector software and LFM schedule.
2
Kit co ntent s
2
1
5
6 A
6
4. Install ceiling mount cover to projector.
Position the ceiling mount cover on the projector
so that the tabs at the front of the ceiling cover
enter the slots on the rear of the projector (view
A). Install and fasten the two screws (reference 6).
R9801322/R9801323
Item
1
5 2
3
4
5
6
4
Fasteners
3
Size
PT3x7
M3x6
M3x8
M3x20
R9801320/R9801321
Item
7
7
7
Fasteners
6
Size
M3x8
M3x14
7
8
5. Install side cover to projector. 6. Mount flexible hose.
Position the side cover on the projector as Thread the flexible hose (reference 9) for the
illustrated. Install two M3x8 screws at the rear exhaust air onto the exhaust duct and fasten it
end of the projector (reference 7) and two M3x20 with the hose clamp (reference 10).
screws at the front end of the projector (reference
8).
Description
Hose clamp
Flexible hose Ø250mm
Ceiling cover
Ceiling cover rib
Exhaust duct
Side cover
Qty Description
2 Ceiling cover rib
2 Ceiling cover
2 Side cover
2 Side cover
Description
Air inlet filter
Qty Description
1 Air inlet filter
2 Air inlet filter
9
10
601-0326-01