Technica Engineering 100BASE-T1 MEDIACONVERTER BCM User Manual

Technica Engineering 100BASE-T1 MEDIACONVERTER BCM User Manual

Transmits data frames directly from the physical layer broadr-reach (100base-t1) to fast ethernet (100base-tx)

Advertisement

100BASE-T1
MEDIACONVERTER
BCM
USER MANUAL
November 2018
Manual-Version: 2.0
Hardware-Version: all

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 100BASE-T1 MEDIACONVERTER BCM and is the answer not in the manual?

Questions and answers

Summary of Contents for Technica Engineering 100BASE-T1 MEDIACONVERTER BCM

  • Page 1 100BASE-T1 MEDIACONVERTER USER MANUAL November 2018 Manual-Version: 2.0 Hardware-Version: all...
  • Page 2: Table Of Contents

    CONTENT GENERAL INFORMATION ................... 3 Functionality and Features of the 100BASE-T1 MediaConverter_BCM ... 3 Warranty and Safety Information ................ 4 Declaration of conformity ..................5 HARDWARE INTERFACES ..................6 Connectors ......................6 2.1.1 Black MQS Connector ................... 6 2.1.2 RJ45 Ethernet connectors ................7 Other Interfaces ....................
  • Page 3: General Information

    1 GENERAL INFORMATION 1.1 Functionality and Features of the 100BASE-T1 MediaConverter_BCM Figure 1—1: 100BASE-T1 MediaConverter_BCM The Technica Engineering 100BASE-T1 MediaConverter_BCM transmits data frames directly from the physical layer BroadR-Reach (100BASE-T1) to Fast Ethernet (100BASE-TX) with constant delay time of 2.0µs. Features: •...
  • Page 4: Warranty And Safety Information

    General Information: Power requirement: 8 to 16 Volt DC (nominal 12 Volt DC) Power consumption: 2 Watt Size: 92 x 63 x 30 mm Weight: 0,2 kg International Protection: IP 2 0 Operating temperature: -40° to +80 °Celsius LINKS: The User can download the latest firmware and documentation for the 100BASE-T1 MediaConvert_BCM here: https://technica-engineering.de/produkt/100base-t1-mediaconverter_bcm/ 1.2 Warranty and Safety Information...
  • Page 5: Declaration Of Conformity

    1.3 Declaration of conformity Figure 1—2: Declaration of conformity 100BASE-T1 MediaConverter_BCM User Manual...
  • Page 6: Hardware Interfaces

    2 HARDWARE INTERFACES 2.1 Connectors On the label on top of the device you can see an overview about all HW-Interfaces of the 100BASE-T1 MediaConverter_BCM. Figure 2—1: Label of 100BASE-T1 MediaConverter_BCM with pinning information 2.1.1 Black MQS Connector The pinning of the ECU connectors is listed on the label on top of the device as well. (See Figure 2—1).
  • Page 7: Rj45 Ethernet Connectors

    The Tyco Electronics (TE) Micro Quad Lock System (MQS) is used. Name Picture Part Number Tyco, MQS Abdeckkappe 2x9 Pol, black 1-967416-1 Alternative 1-1355350-1 Tyco, MQS Buchsengehäuse 2x9 Pol 965778-1 Alternative 962108-2 Tyco crimp contact 928999-1 Table 2—1: Parts of black MQS connector Note: You can use the official Tyco tool for these crimp contacts.
  • Page 8: Other Interfaces

    2.2 Other Interfaces 2.2.1 DIP-Switches The 100BASE-T1 MediaConverter_BCM has two DIP-Switches for configuration (see Chapter 3). 2.2.2 Status LEDs The 100BASE-T1MediaConverter_BCM has two status LEDs at the frontside of the case for the 100BASE-T1 Port. Upper LED: Green Color. It is lit when there is a linkup on the 100BASE-T1 port. Lower LED: Yellow Color.
  • Page 9: Configuration Of The Device

    3 CONFIGURATION OF THE DEVICE The 100BASE-T1 MediaConverter is configured by two DIP-Switches on the front of the device. DIP-Switch Status Description ON (up) 100BASE-T1 Port is set to Master OFF (down) 100BASE-T1 Port is set to Slave ON (up) 100BASE-T1 Port is set to FullOut OFF (down) 100BASE-T1 Port is set to HalfOut...
  • Page 10: 100Base-T1 Filter

    4 100BASE-T1 FILTER There are different BroadR-Reach Filter in different Hardware versions of the 100BASE- T1 MediaConverter_BCM: The following BR-Filter is used in the Hardware version 3.0: In Version 3.0 the Würth CMC 510010003 is used for L32. In Version 3.0a the TDK CMC ACT45L - 2 01 - 2P is used for L32. Figure 4—1: BR-Filter for HW v3.0 and v3.0a The following BR-Filter is used in the Hardware version 2.0: Figure 4—2: BR-Filter for HW v2.0...
  • Page 11: Additional Information

    5 ADDITIONAL INFORMATION • The 100BASE-T1 MediaConverter_BCM is optimized for automotive use. The maximum cable length for 100BASE-T1 segments is limited to 15 meters 100BASE-T1 MediaConverter_BCM User Manual...
  • Page 12: List Of Figures

    6 LIST OF FIGURES Figure 1—1: 100BASE-T1 MediaConverter_BCM ............. 3 Figure 1—2: Declaration of conformity ................5 Figure 2—1: Label of 100BASE-T1 MediaConverter_BCM with pinning information ..6 Figure 4—1: BR-Filter for HW v3.0 and v3.0a ..............10 Figure 4—2: BR-Filter for HW v2.0..................10 100BASE-T1 MediaConverter_BCM User Manual...
  • Page 13: Changelog

    7 CHANGELOG Version Chapter Description Date First release Rework of design and update of all information 21.09.2018 100BASE-T1 MediaConverter_BCM User Manual...
  • Page 14: Contact

    8 CONTACT If you have any questions regarding this product, please feel free to contact us: Technica Engineering GmbH Leopoldstr. 236 80807 München Germany Fax: +49-89-34290265 Info@technica-engineering.de www.technica-engineering.de 100BASE-T1 MediaConverter_BCM User Manual...

Table of Contents