Advertisement
Quick Links
Glacier King Bed
Assembly Instructions
Before you
Start, here
are some
helpful
advices.
Revision number 1/1
215-00946 (Sprung slats)
1. We suggest you spend a short time reading through this leaflet and then
follow the simple step by step instructions.
2. If you follow the instructions carefully the end result should be worth the effort.
3. Do not discard any of the packaging until you have checked that you
have all the parts and the pack of fittings.
4. Assemble this product on a carpet.
5. To ensure an easier assembly, we strongly advise that all fittings are only
finger tightened during initial assembly. Only upon completion of the.
Assembly should all fixing points be fully tightened.
6. We recommend a periodic check on all fixing points to make sure they remain
fully tightened.
7. Keep glue and fittings out of children's reach.
In the unlikely event that this product has missing or damaged parts, please call
08442 920000 to obtain spares
215-00945 (Solid slats)
Advertisement
Related Manuals for DREAMS Glacier King Bed
Summary of Contents for DREAMS Glacier King Bed
- Page 1 215-00945 (Solid slats) Glacier King Bed 215-00946 (Sprung slats) Assembly Instructions Before you 1. We suggest you spend a short time reading through this leaflet and then follow the simple step by step instructions. Start, here 2. If you follow the instructions carefully the end result should be worth the effort.
- Page 2 PARTS Fittings M6×15mmx16pcs M6×10mm x 14pcs M6×35mm x 6pcs M6 × 6pcs Washer ( ) x 22pcs 16mm NO. PART LIST (1) HB bottom post right 1 (2) HB bottom post left 1 Plastic Washer x 16pcs (3) FB bottom post (4) Top Posts Allen key ×...
- Page 3 ASSEMBLY STEP1 Attach Cross rails (6) to HB bottom posts (1)(2)(3) by using bolts A, Plastic washer (1).将上立柱花(4)螺孔依次 F, washer E, Spring Washer 对准右下立柱花（1）、左 H, and tighten with Allen Key 下立柱花（2）、前下立柱 花（3）上的牙杆，上立柱 花(4)向下旋转,直至锁紧锁 Attach Side rail (5) to HB 到位 bottom posts (1)(2)(3) by using bolts A, Plastic washer F, washer E, Spring Washer...
- Page 4 ASSEMBLY STEP 2 Insert ends of HB panel (9) and HB Cross tubing (10) into holes on HB bottom posts (1)(2), secure the HB panel (9) onto posts by using bolts B, washer I and tighten with Allen Key G. Revision number 1/1...
- Page 5 ASSEMBLY STEP 3 Screw the Top Posts (4) onto bottom posts (1)(2)(3) by turning the top posts (4) clock-wise. Revision number 1/1...
- Page 6 ASSEMBLY Loosen the metal balls on STEP4 top of posts, align the top section of the posts in right angle. And insert the canopy rails (7)(8) into holes on top posts (4). Secure the canopy rails (7)(8) onto top posts (4) by using bolts B, washer I, and tighten with Allen Key Tighten the metal balls on...
- Page 7 Both slats on "step 5" and "step 6" can be assembled to the bedstead. you can make a choice between the two slats. OPTION"A": DREAMS FIXED WOOD SLATS （1）Carefully locate the slats onto the unit. （2）Use bolt (C) and JCN nut...
- Page 8 ASSEMBLY STEP6 OPTION"B":DREAMS SPRUNG SLATS (1) Use the bolt to fix support leg onto the slat frame. Please note that these bolts are to be found inside the slat frame box. (2) Carefully locate the slats onto the unit. (3) Use bolt (B) and JCN nut (C) to fix the unit using Allen Key (F).
Need help?
Do you have a question about the Glacier King Bed and is the answer not in the manual?
Questions and answers