Banda Audioparts VIKING 5000 User Manual

Banda Audioparts VIKING 5000 User Manual

Advertisement

Made in Brazil
WARRANTY
Banda Audioparts warrants this equipment to be free of all defects in material and workmanship for
a period of 12 months from the date of purchase
Within the period of this warranty, Banda Audioparts will repair or replace, free of charge, any part
proving defective in material or workmanship.
Warranty Exclusions:
1. Damage resulting from misuse, abuse, accident, alterations or improper installation;
2. Damage resulting from installation in surfaces subjected to high levels of vibration;
3. Corrective work necessitated by repairs made by anyone other than a Banda Audioparts
authorized service technician;
This warranty does not cover shipping costs.
The defective equipment must be shipped to the factory or to an authorized service center
Rua Manoel Joaquim Fiho, 353 - Jardim Santa Terezinha II - Paulínia - SP - Brazil
CEP: 13148-133
Banda Audioparts reserves the right to change the product and its specifications at any time
without prior notice.
Note:Permanent Technical Support
After the warranty expires, Banda Audioparts will continue to provide extensive technical
assistance directly or through its network of authorized service, charging, however, the repair
services and replacement of components
Warning: Continuous expose to sound pressure levels over 85dB may cause permenent hearing loss.
REGISTRATION DATA
Name:
Invoice:
Date:
Phone:
Address:
Shop:
Phone:
COSTUMER SERVICE:
+55 (19) 3844-7173 - (19) 3844-7465 - (19) 3844-4923 •
BANDA@BANDAAUDIOPARTS.COM
www.bandaaudioparts.com
12
USER MANUAL
VIKING

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VIKING 5000 and is the answer not in the manual?

Questions and answers

Summary of Contents for Banda Audioparts VIKING 5000

  • Page 1 Banda Audioparts warrants this equipment to be free of all defects in material and workmanship for a period of 12 months from the date of purchase Within the period of this warranty, Banda Audioparts will repair or replace, free of charge, any part proving defective in material or workmanship.
  • Page 2: General Technical Specification

    Protection triggered • Operation Topology: Full Bridge Class D Check if the internal fuse is blown. If so, replace it with a same current rate fuse (Megaval 225A) Viking 5000. • Variable Linkwitz-Riley active crossover: 18Hz - 8000Hz (12dB/octave) (Megaval 250A) Viking 8000.
  • Page 3: Connection Examples

    CONNECTION EXAMPLES OUTPUT VIKING 8000Wrms 2 ohms VIKING 5000 1 ohm • Output power: • Current draw at full power (average music program): 246A* VIKING 5000 2 ohms • Output power: • Current draw at full power (average music program): 246A* VIKING 8000 1 ohm •...
  • Page 4: Technical Specification

    1. Negative power input (ground): connect to car chassis. 2. Protection fuse: 225A (VIKING 5000) 250A (VIKING 8000) 3. Remote input: connect to radio/cd remote output. 4. Positive power input (+12Vdc): connect to baterry positive terminal.
  • Page 5: Instalation Instructions

    TECHNICAL SPECIFICATION CONNECTION EXAMPLES VIKING 5000Wrms 2 ohms Signal input and power output section Positive speaker output Subsonic Control Crossover Control Signal input (RCA) Subsonic control Crossover control 2000 Negative speaker output 120Hz 20kHz Sets the beggining of response Sets the end of response 8 ohms 1250Wrms woofers x 4 wired in parallel INSTALATION INSTRUCTIONS Wire the power cables in thisorder: first GND, second +12Vdc and for last the remote.
  • Page 6: Important Notes

    TECHNICAL SPECIFICATION CONNECTION EXAMPLES Important notes: • Use 1/0AWG power cables for both GND and +12Vdc. VIKING 5000Wrms 1 ohm • Do not use impedance load lower than the amplifier specification. This can damage the equipment. • Use wire solder for tinning the cable end for better electrical contact. Loose electrical connection can cause malfunction, heating and even fire •...

This manual is also suitable for:

Viking 8000

Table of Contents