Related Manuals for Zennio BIN 44
Summary of Contents for Zennio BIN 44
- Page 1 ➢ BIN 44 / 4X / 2X Universal Interface with Binary Inputs and/or LED Lighting & Electronic Relay Outputs ZIO-BIN44 ZIO-BIN4X ZIO-BIN2X Application program version: [1.1], [1.2] User manual edition: [1.2]_a www.zennio.com...
-
Page 2: Table Of Contents
BIN 44 / 4X / 2X CONTENTS Contents ............................2 Document updates ........................3 Introduction .......................... 4 1.1 BIN ............................ 4 1.1.1 BIN 44 ........................4 1.1.2 BIN 4X ........................4 1.1.3 BIN 2X ........................5 1.2 Installation ........................6 Configuration......................... -
Page 3: Document Updates
BIN 44 / 4X / 2X DOCUMENT UPDATES Version Changes Page(s) Application program changes: • Optimisation of the binary inputs, electronic relay [1.1]_a control and heartbeat module. Minor text changes. http://www.zennio.com Technical Support: http://support.zennio.com... -
Page 4: Introduction
1 INTRODUCTION 1.1 BIN The BIN product family from Zennio consists of a variety of small-size KNX interfaces, designed to be installed, for instance, inside electric appliance boxes. They allow connecting a variable number of binary inputs (pushbuttons, switches) while they also provide LED and electronic relay control outputs (up to 12V DC, 2 mA). -
Page 5: Bin 2X
BIN 44 / 4X / 2X 1.1.3 BIN 2X 2 input / output channels, freely configurable as: ➢ Binary inputs. ➢ LED Lighting Output. ➢ Electronic Relay Control (Heating Actuator). http://www.zennio.com Technical Support: http://support.zennio.com... -
Page 6: Installation
BIN 44 / 4X / 2X 1.2 INSTALLATION BIN is connected to the KNX bus through the incorporated terminal connector, while the input lines are connected to BIN through a screw terminal block, bundled with the stripped cables already connected. - Page 7 BIN 44 / 4X / 2X To obtain further information about the technical features of BIN 44 / 4X / 2X and on security and installation procedures, please refer to the Datasheet of the device, bundled with the original packaging and also available at the http://www.zennio.com...
-
Page 8: Configuration
BIN 44 / 4X / 2X 2 CONFIGURATION 2.1 GENERAL After importing the corresponding database in ETS and adding the device into the topology of the desired project, the configuration process begins by entering the Parameters tab of the device. - Page 9 (or which channels will behave as inputs and which channels as outputs, in the case of BIN 44, see Figure 4). After enabling them, additional tabs will be incorporated to the tab tree on the left. These functions and their parameters will be explained in later sections of this document.
-
Page 10: Inputs / Outputs
BIN 44 / 4X / 2X 2.2 INPUTS / OUTPUTS 2.2.1 BIN 44 BIN 44 incorporates four inputs and four outputs, configurable as: Inputs: pushbuttons or switches. See section 2.2.3. Outputs: ➢ Low-current LED lighting controls, for low current LED control. - Page 11 BIN 44 / 4X / 2X such cases, it will be possible to switch the mode by means of a one-bit object and/or a scene object. These settings are common for all outputs configured as LEDs. On the contrary, timers, flashing and status objects can be configured independently for each output.
- Page 12 BIN 44 / 4X / 2X In case of enabling the night mode, some more options can be configured: Figure 7. LED Ouputs - General Configuration - Night Mode Brightness Mode after ETS download [Normal/Night]: sets which of the two modes will be active after an ETS Download.
- Page 13 BIN 44 / 4X / 2X 2.2.4.2 OUTPUT X: LED LIGHTING – CONFIGURATION As already stated, each LED output allows an independent configuration of its status object, timer and flashing functions. The Timer function consists in performing a single, timed switch-on / switch-off cycle when a specific trigger object is received.
-
Page 14: Electronic Relay Control (Heating Actuator)
2.2.5 ELECTRONIC RELAY CONTROL (HEATING ACTUATOR) Please refer to “Electronic Relay Control in Heating Systems” specific manual, available in the BIN product section at the Zennio website, http://www.zennio.com. Note: BIN does not implement the following options, although they are included in the above document: Overload/short-circuit notification. -
Page 15: Annex I. Communication Objects
BIN 44 / 4X / 2X ANNEX I. COMMUNICATION OBJECTS “Functional range” shows the values that, with independence of any other values permitted by the bus according to the object size, may be of any use or have a particular meaning because of the specifications or restrictions from both the KNX standard or the application program itself. - Page 16 BIN 44 / 4X / 2X 0x8 (Stop) 0x9 (Inc. by 100%) … 0xF (Inc. by 1%) 1 Bit C T - - - DPT_Switch [Ix] [Short Press] Light On Sending of 1 (On) 1 Bit C T - - -...
- Page 17 BIN 44 / 4X / 2X 0x0 (Stop) 0x1 (Dec. by 100%) … 0x7 (Dec. by 1%) 4 Bit C T - - - DPT_Control_Dimming [Ix] [Long Press] Darker Long Pr. -> Darker; Release -> Stop 0x8 (Stop) 0x9 (Inc. by 100%) …...
- Page 18 BIN 44 / 4X / 2X 18(**) 26(*), 31(*), 36(*), 41(*), 1 Bit C - - W - DPT_Scene_AB [LEDx] Inverted On/Off 0 = On; 1 = Off 14(**), 19(**) 27(*), 32(*), 37(*), 42(*), 1 Bit C T R - -...
- Page 19 BIN 44 / 4X / 2X , 71 , 95 1 Bit C T R - - DPT_Switch [HCx] Control Value - 1 bit (Status) 0 = Off; 1 = On , 49 (**) (**) , 72 , 96 1 Byte...
- Page 20 Join and send us your inquiries about Zennio devices: http://support.zennio.com Zennio Avance y Tecnología S.L. C/ Río Jarama, 132. Nave P-8.11 45007 Toledo (Spain). Tel. +34 925 232 002 www.zennio.com info@zennio.com...