Related Manuals for Titan TTK550LWM
Summary of Contents for Titan TTK550LWM
- Page 1 TTK550LWM RIDE-ON MOWER OWNER’S MANUAL WARNING! Read this manual carefully before using the machine. Supported by For all your Warranty, Parts and Service needs 0845 601 4221 www.servicelink.org.uk...
- Page 2 Please retain this handbook in case you need to refer to any of the information in the future. Your TITAN Ride On Lawnmower comes with a 1 year guarantee, so should it develop a fault within this period contact the Service Link helpline on 0845 601 4221.
-
Page 3: Getting Started
TTK550LWM by TITAN Let’s get started These instructions are for your safety. Please read through them thoroughly before use and retain them for future reference. Getting started... Your product Technical data Accessory list Safety instructions Unpacking and assembly more detail... -
Page 4: Your Product
Your product TTK550LWM by TITAN Your product IDENTIFICATION OF THE MACHINE The identification label located under the seat has the essential data of each machine. The serial number (6) must be quoted when you require technical assistance or spare parts. -
Page 5: Technical Data
Technical and legal TTK550LWM by TITAN informations Technical data Electric Start Mechanical transmission Electrical system ......12 V Tyres 11”-13” Battery ........7.2 Ah Forward speed (approximate) in Forward gear ..1.4 - 5.5 km/h Front tyres ......11 x 4.00-4”... -
Page 6: Accessory List
Accessory list TTK550LWM by TITAN Accessory list (Available separately) 1. REAR DISCHARGE GUARD KIT 2. TOWING HITCH For use in place of the grass-catcher when the cuttings are not to be For towing a small trailer. collected. 3. KIT FOR “MULCHING”... -
Page 7: Safety Instructions
Safety instructions TTK550LWM by TITAN Safety instructions SAFETY DECALS Your machine must be used with care. Pictograms have been placed on the machine to remind you of the main precautions to be taken during use. If placed on a label, they are considered an integral part of the machine. -
Page 8: General Safety
Safety instructions TTK550LWM by TITAN General safety DESCRIPTION OF THE MACHINE AND ITS RANGE OF USE This machine is a garden tool and precisely a ride-on mower. The machine is equipped with an engine which drives a cutting unit protected by a casing, as well as a transmission unit that moves the machine. -
Page 9: Additional Safety
Safety instructions TTK550LWM by TITAN Additional safety HOW TO READ THE MANUAL The manual describes several machine models that can mainly differ in: – type of drive: mechanical or hydrostatic; – electric or manual start-up; – presence of accessories or fittings The symbol “... - Page 10 Safety instructions TTK550LWM by TITAN 7) The machine is equipped with a series of safety microswitches and devices which must never be removed, altered or tampered with. Removing these devices invalidates the warranty and the manufacturer declines any responsibility. B) PREPARATION 1) While mowing, always wear substantial footwear and long trousers.
-
Page 11: Maintenance And Storage
Safety instructions TTK550LWM by TITAN 12) Do not change the engine governor settings or overspeed the engine. 13) Before leaving the operator’s position: – disengage the blade; – go into neutral and apply the parking brake; – stop the engine and remove the key Electric start). -
Page 12: Before You Start
Before you start TTK550LWM by TITAN Unpacking and assembly For storage and transport reasons, some components of the machine are not directly installed in the factory, but have to be assembled after their removal from the packing. Final assembly is carried out by following these simple instructions. -
Page 13: Hydrostatic Transmission
Before you start TTK550LWM by TITAN Additional safety • Use equipment marked “A”. Apply plates (1) to the two supporting brackets (2) and (3), as shown in the figure. Screw (4) the two brackets (2) and (3) to the chassis supports, taking care they are in the correct right and left positions. -
Page 14: Fitting The Seat
Before you start TTK550LWM by TITAN Fit the dashboard cover (5) making sure all fastenings click into their respective housings correctly. Fit the steering wheel (6) onto the caster (3) with all the spokes directed towards the seat. Fit the steering wheel fastening it with the screws (7-a/b/c) supplied, in the indicated order. -
Page 15: Connecting The Battery
Before you start TTK550LWM by TITAN CONNECTING THE BATTERY Electric Start The battery (1) is located under the seat and can be reached by moving the cover (2). Connect the battery connector (3) to the machine connector (4) and arrange the wire (5) so that it is held firmly in place (7). - Page 16 Before you start TTK550LWM by TITAN FITTING THE “MULCHING” ACCESSORY (if provided) • Use equipment marked “E”. Fit the handle (1) on the deflector cap (2) using the pin (3) pushing it to the end with a hammer. Insert an end of the spring (4) in the deflector...
- Page 17 Before you start TTK550LWM by TITAN ASSEMBLY OF THE REAR DISCHARGE GUARD (if provided) Follow sequences on the instructions sheet supplied.
- Page 18 TTK550LWM by TITAN more detail... Operation Care and maintenance Troubleshooting Recycling and disposal EC declaration of conformity...
-
Page 19: Operation
Operation TTK550LWM by TITAN 1. STEERING WHEEL Turns the front wheels. 2. PARKING BRAKE LEVER This lever is to stop the machine from moving when it has been parked and must always be engaged before leaving the machine. – The brake is engaged by fully pressing the pedal (11 - 21) and moving the lever to position «A». -
Page 20: Key Ignition Switch
Operation TTK550LWM by TITAN 3. BLADE ENGAGEMENT AND BRAKE LEVER This lever has two positions, as shown on the label: Position «A» = Blade disengaged Position «B» = Blade engaged – If the blade is engaged when safety conditions have not been complied with, the engine shuts down. -
Page 21: Mechanical Transmission
Operation TTK550LWM by TITAN Manual start 7. PULL START HANDLE To start the engine, take the starter cable handle and give it a firm tug. Then put the handle back in its seat, guiding the cable as it automatically rewinds. -
Page 22: Brake Pedal
Operation TTK550LWM by TITAN 12. SPEED CHANGE LEVER This lever has 6 positions for the 4 forward speeds, the neutral position «N» and reverse «R». – To change gear, press the pedal (11) halfway down and move the lever to the desired gear. -
Page 23: Safety Recommendations
Operation TTK550LWM by TITAN SAFETY RECOMMENDATIONS Do not tamper with or remove the safety devices fitted on the machine. REMEMBER THAT THE USER IS ALWAYS RESPONSIBLE FOR DAMAGE AND INJURY TO OTHERS. Before using the machine: – read the general safety regulations, paying particular attention to driving and cutting on slopes;... -
Page 24: Directions Before Starting
Operation TTK550LWM by TITAN Electric Start – the speed change is activated ( from page 19 - 22) or the drive pedal ( from page 19 - 22) with the parking brake on. DIRECTIONS BEFORE STARTING Before starting to mow, it is necessary to carry out several checks and operations to ensure you can work efficiently and in maximum safety. - Page 25 Operation TTK550LWM by TITAN IMPORTANT Do not drip petrol onto the plastic parts to avoid damaging them. In the event of accidental spills or leaks, rinse immediately with water. The warranty does not cover for damage to plastic parts of the bodywork or the engine caused by petrol.
- Page 26 Operation TTK550LWM by TITAN • Preparation for mowing and rear grass discharge Hook on the rear discharge guard (1) inserting the two connections (2) in the holes on the two supports (3). Fasten the lower part to the rear plate using the pins (4) and split pins (5).
-
Page 27: Using The Machine
Operation TTK550LWM by TITAN – A badly sharpened blade pulls at the grass and causes the lawn to turn yellow. – A loose blade causes unwanted vibrations and can be dangerous. Do not use the machine if you are unsure whether it is working safely or efficiently. -
Page 28: Hydrostatic Transmission
Operation TTK550LWM by TITAN Moving without mowing The machine has not been approved for use on public roads. It has to be used (as indicated by the highway code) in private areas closed to traffic. NOTE When moving the machine, the blade must be disengaged and the cutting deck put at its highest position. -
Page 29: Grass Cutting
Operation TTK550LWM by TITAN Hydrostatic transmission The machine MUST be stopped before reverse can be en ga ged. When the machine has stopped moving, start reversing by pressing the drive pedal in direction «R». GRASS CUTTING Engaging the blade and forward movement When you have reached the area to be mowed, –... - Page 30 Operation TTK550LWM by TITAN 3. The blade must be in good condition and well sharpened so that the grass is cut straight without any ragged edge that leads to yellowing at the ends. 4. The engine must run at full speed, both to ensure a sharp cut of the grass and to get the necessary thrust to push the cuttings through the outlet.
- Page 31 Operation TTK550LWM by TITAN Mechanical transmission Never ride the machine on slopes in neutral gear or with the clutch out! Always engage a low gear before leaving the machine stopped and unattended. Hydrostatic transmission Go down slopes with your foot off the drive pedal to use the braking effect of the hydrostatic drive when the transmission is not engaged.
- Page 32 Operation TTK550LWM by TITAN End of work Once you have finished mowing, stop the machine and engage the parking brake. Electric Start – shift the accelerator lever to «SLOW»; – switch off the engine by turning the key to «STOP»;...
- Page 33 Operation TTK550LWM by TITAN – connect a water hose to its pipe fitting (1), and run water through it; – sit at the operator’s position; – lower the cutting deck completely; – start the engine and stay in neutral; – engage the blade and leave it to turn for a few minutes.
-
Page 34: Care And Maintenance
Care and maintenance TTK550LWM by TITAN Care and maintenance SAFETY RECOMMENDATIONS Routine and accurate maintenance is essential in maintaining original machine safety and performance levels. Before cleaning or doing maintenance work, take out the ignition key and read the relevant instructions. Wear adequate clothing and work gloves whenever your hands are at risk. -
Page 35: Routine Maintenance
Care and maintenance TTK550LWM by TITAN ROUTINE MAINTENANCE The following table is to help you maintain your machine’s safety and performance. It shows the main maintenance and lubrication operations and their frequency. To the right of each item, there is a box where you can write the date or after how many operating hours the work was carried out. -
Page 36: Troubleshooting
Troubleshooting TTK550LWM by TITAN Troubleshooting PROBLEM LIKELY CAUSE SOLUTIONS Electronic card blocked due to: Turn the key to «STOP» and look for Electric start the cause of the problem: 1. With the key on «START» – flat battery – recharge battery... - Page 37 Troubleshooting TTK550LWM by TITAN PROBLEM LIKELY CAUSE SOLUTIONS – check that spark plug caps are – faulty ignition firmly fitted – check that the electrodes are clean and have the correct gap – check connections – earth connections of the 5.
- Page 38 Troubleshooting TTK550LWM by TITAN PROBLEM LIKELY CAUSE SOLUTIONS – blade unbalanced – Contact your dealer 10. Unusual vibrations – Contact your dealer – blade loose while working – fixing bolts loose – check and tighten all the fixing bolts of the engine and frame –...
-
Page 39: Recycling And Disposal
Recycling and disposal TTK550LWM by TITAN Service Link This product is supported by Service Link. If you have been unable to find the information you require above please call the Service Link helpline. Here you will find 1-2-1 help and advice from HELPLINE garden machinery repair specialists. -
Page 40: Ec Declaration Of Conformity
EC Declaration of conformity TTK550LWM by TITAN DICHIARAZIONE CE DI CONFORMITÁ (Direttiva Macchine 2006/42/CE, Allegato II, parte A) Déclaration CE de Conformité EC Conformity Statement EG-Konformitätserklärung (Directive Machines 2006/42/CE, Annexe II, partie (Machine Directive 2006/42/EC, Annex II, part A) (Maschinenrichtlinie 2006/42/EG, Anhang II, Teil 1. -
Page 42: Identification Of The Machine
As soon as you have purchased the machine, write the machine identification data (3 - 5 - 6) found on the identification label in the spaces provided ( 2.1 - IDENTIFICATION OF THE MACHINE). 171505874/0...