Page 1
MN026007EN EAFR-110 Current and Arc Light Sensor Relay User Manual...
Page 2
CONTENTS OF THIS DOCUMENT SHALL NOT BECOME PART OF OR MODIFY ANY CONTRACT BETWEEN THE PARTIES. In no event will Eaton be responsible to the purchaser or user in contract, in tort (including negligence), strict liability or other- wise for any special, indirect, incidental or consequential damage or loss whatsoever, including but not limited to damage or...
EAFR-110PB is the same point sensor unit with relay T3 in a normally closed configuration. – Normally closed – Normally open – System failure – Software – Microprocessor EAFR-110 Current and Arc Light Sensor Relay User Manual MN026007EN February 2016 www.eaton.com...
One system failure relay, form C output (SF). ● ● 2.2 Simplified Block Diagram The simplified block diagrams in Figures 2 and 3 show the main components of the EAFR-110 relay. EAFR-110 Current and Arc Light Sensor Relay User Manual MN026007EN February 2016 www.eaton.com...
Page 7
150 ms CBFP Time: 100 ms Phase Sensor: Ground Sensor: HSO1 HSO2 [ x In ] 0.05 Current [ x In ] Self supervision Control and power supply EAFR-110 Current and Arc Light Sensor Relay User Manual MN026007EN February 2016 www.eaton.com...
Page 8
150 ms CBFP Time: 100 ms Phase Sensor: Ground Sensor: HSO1 HSO2 [ x In ] 0.05 Current [ x In ] Self supervision Control and power supply EAFR-110 Current and Arc Light Sensor Relay User Manual MN026007EN February 2016 www.eaton.com...
LED activation function is latched (steady light). To sions. Sensor channels S4 and S5 are not in use in EAFR- clear the LED the “SET” button should be pressed. 110F version. EAFR-110 Current and Arc Light Sensor Relay User Manual MN026007EN February 2016 www.eaton.com...
SET button. HSO2 Normal status. HSO 2 activated. Check the reason for activation. Clear the fault and reset indications by pushing SET button. EAFR-110 Current and Arc Light Sensor Relay User Manual MN026007EN February 2016 www.eaton.com...
All LED indications will remain active until a reset is performed by the operator, even in the case of disconnecting the auxiliary power supply (see Section 3.7: Non-volatile Memory). EAFR-110 Current and Arc Light Sensor Relay User Manual MN026007EN February 2016 www.eaton.com...
Configuration select Selection of standard arc configuration. Refer to MN026009EN. Refer to MN026009EN. Configuration select Selection of standard arc configuration. Refer to MN026009EN. Refer to MN026009EN. Configuration select EAFR-110 Current and Arc Light Sensor Relay User Manual MN026007EN February 2016 www.eaton.com...
Page 13
Phase sensor: 1A / 5A nominal current selection. Earth current ground sensor nominal 1A nominal current. 5A nominal current. Earth Ground sensor: 1A / 5A current selection. EAFR-110 Current and Arc Light Sensor Relay User Manual MN026007EN February 2016 www.eaton.com...
Page 14
Current Current Current Ig set Current set [ x In ] [ x In ] X3-12,11 X3-10,9 X3-8,7 X3-6,5 X2-15 X2-14 X1-15 X1-14 BI 1 BI 2 EAFR-110 Current and Arc Light Sensor Relay User Manual MN026007EN February 2016 www.eaton.com...
8,000 lux. This default set can be also designed as 25,000 and 50,000 lux according to the demand of user’s application. The sensor does not require user settings. Detection radius is 180 degrees. EAFR-110 Current and Arc Light Sensor Relay User Manual MN026007EN February 2016 www.eaton.com...
The fixed light sensitivity of the EAFR-07 sensor is 8,000 Lux. The sensor does not require user settings. The loop sensor’s detection radius is 360 degrees (see Figure 11). EAFR-110 Current and Arc Light Sensor Relay User Manual MN026007EN February 2016 www.eaton.com...
8,000 Lux. The sensor does not require user settings. The loop sensor’s detection radius is 360 degrees (see Figure EAFR-110P Yes Yes (with Yes (with Yes (with Fiber 12). Fiber Fiber Option) Option) Option) EAFR-110F EAFR-110 Current and Arc Light Sensor Relay User Manual MN026007EN February 2016 www.eaton.com...
EAFR-101 or EAFR-110P relay (see Figure 15). Attach the connector back to the sensor PCB (see Figure 17). Figure 17. EAFR-01 Sensor Connection Step 5. EAFR-110 Current and Arc Light Sensor Relay User Manual MN026007EN February 2016 www.eaton.com...
Page 19
After completing the system auto-configuration setting, close both end side covers back (see Figure 20). EAFR-110 Current and Arc Light Sensor Relay User Manual MN026007EN February 2016 www.eaton.com...
When an open CT alarm is issued, the SF-relay is released, C = Current the ERROR LED turned on, and corresponding IL1, IL2, and IL3 LEDs starts blinking. EAFR-110 Current and Arc Light Sensor Relay User Manual MN026007EN February 2016 www.eaton.com...
The state of the SF relay remains the same until the relay returns to a healthy condition and the SF relay is energized again. EAFR-110 Current and Arc Light Sensor Relay User Manual MN026007EN February 2016 www.eaton.com...
In this case, Tx will be utilized to control the arc quenching system. The relay is sending a continuous light pulse to arc quenching system for self- supervision purposes. EAFR-110 Current and Arc Light Sensor Relay User Manual MN026007EN February 2016 www.eaton.com...
(482.6 mm) rack (height of 4U and 1/4 of a relay wide). Figure 26. EAFR-102 Dimensions in Millimeters (In.) (Side View). 175 (6.89) 160 (6.30) 10 (0.39) (0.67) 157 (6.18) 10 (0.39) EAFR-110 Current and Arc Light Sensor Relay User Manual MN026007EN February 2016 www.eaton.com...
Page 26
Ea to n Ar c Fla sh Re lay PO WE R ER RO R 157 (6.18) HS O1 BO 1 HS O2 SE T EA FR -11 0P 102 (4.01) EAFR-110 Current and Arc Light Sensor Relay User Manual MN026007EN February 2016 www.eaton.com...
Steps 4 and 5. 10. Press the SET push-button to reset all indications and latches. 11. Repeat the testing procedure for all sensors. EAFR-110 Current and Arc Light Sensor Relay User Manual MN026007EN February 2016 www.eaton.com...
BI2, verify that a trip has occurred by repeating Steps 4 and 5. 15. Press the SET push-button to reset all indications and latches. 16. Repeat the testing procedure for all sensors. EAFR-110 Current and Arc Light Sensor Relay User Manual MN026007EN February 2016 www.eaton.com...
Sensor 1 Sensor 2 Sensor 3 Fiber Sensor Channel (Option) BIN 1 BIN 2 Phase Current IL1, IL2, AND IL3 Earth Current Ig Tested by: Approved by: EAFR-110 Current and Arc Light Sensor Relay User Manual MN026007EN February 2016 www.eaton.com...
Page 30
L/R = 40 ms Standby Current 90 mA Contact Material Semiconductor 11.6 Binary Output BO1 Rated Voltage +24 Vdc Rated Current 20 mA (max) Number of Outputs EAFR-110 Current and Arc Light Sensor Relay User Manual MN026007EN February 2016 www.eaton.com...
2 to 13.2 Hz ± 3.5 mm (0.14 in.) 13.2 to 100 Hz, ± 1.0 g (0.04 oz) Shock/Bump Test Acc. to IEC 60255-21-2 20 g, 1,000 bumps/dir. EAFR-110 Current and Arc Light Sensor Relay User Manual MN026007EN February 2016 www.eaton.com...