Related Manuals for StandDesk Dual Motor Stand Desk
Summary of Contents for StandDesk Dual Motor Stand Desk
- Page 1 DUAL MOTOR F2 - DM - TS...
-
Page 2: Caution / Information
Keep children away from fully electric standing desks, control boxes, and controllers. There is a risk of injury or electric shock. Keep all electrical components away from liquids. Do not sit, stand, crawl or lie on or under the StandDesk Frame. Do not place any objects taller than 20" underneath the StandDesk. - Page 3 Middle Slat Stabilizing Feet Control Box Holder Support Brace Foot Plate Control Box Handset Power Cords Cable Management Tray (optional) Crossbar (optional) Allen Key Hex Key ST3.5x19 ST4.8x19 M6x12 M6x25 M6x30 M6x35 Inserts Washers DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS...
- Page 4 STEP ONE Lay out all of the parts and hardware to ensure you have everything. Assemble your frame on the underside of your desk top. holes for To do this, make sure the top opt. Crossbar is laying on a soft surface such as carpet or towel with the screw holes facing up.
- Page 5 STEP TWO IMPORTANT! Place the Support Braces on the DESK TOP so they match up with the pre-drilled holes in your top. Attach the SUPPORT BRACES to the outside of each LEG using x4 M6x12 BOLTS. x4 M6x12 DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS...
- Page 6 STEP THREE Use x6 ST4.8x19 SCREWS to attach your SUPPORT BRACES to your TOP. Attach the HANDSET to the front edge of the desk with x2 ST3.5x19 SCREWS. If your desk does not have pre-drilled holes you may have to drill your own.
- Page 7 STEP FOUR If the MIDDLE SLATS arrive disassembled, slide the two MIDDLE SLAT pieces over the U shaped piece. Place your MIDDLE SLATS with the pre-installed bolts facing up. Adjust the length of the SLATS to match the width of the LEGS by loosening these bolts and pulling the SLATS apart.
- Page 8 STEP FIVE Place x1 STABILIZING FOOT PLATE on top of each LEG. Make sure the "lip" of the PLATE is touching the LEG and the smooth side is facing up. DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS...
- Page 9 STEP SIX Place x1 FOOT on top of each STABILIZING FOOT PLATE with Black Pads on the ends of the feet facing up. Attach each FOOT using x4 M6x12 BOLTS. PRO TIP! Install the bolts in a diagonal pattern to ensure all the holes are aligned before fully tightening.
- Page 10 STEP SEVEN OPTIONAL UPGRADE - CABLE MANAGEMENT TRAY Remove the x2 PRE-INSTALLED M6x35 BOLTS from the BACK MIDDLE SLAT. Attach the CABLE MANAGEMENT TRAY to the BACK MIDDLE SLAT, making sure the tray is facing the back of your desk using x4 M6x12 BOLTS and x4 WASHERS to attach.
-
Page 11: Control Box
STEP EIGHT Secure the CONTROL BOX to the CONTROL BOX HOLDER with x2 INSERTS. Be sure to press the INSERTS down firmly. The screw head should be flush with the rim of the CONTROL BOX. x2 INSERTS DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS... - Page 12 STEP NINE Attach the CONTROL BOX HOLDER to the FRONT MIDDLE SLAT using x2 M6x12 BOLTS. The CONTROL BOX HOLDER should be situated in between both MIDDLE SLATS. x2 M6x12 DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS...
- Page 13 STEP TEN Connect the HANDSET CORD, MOTOR CORDS, and POWER CORD to the CONTROL BOX . Go back and ensure all the screws and bolts are fully tightened! Then carefully flip your desk. Plug the desk into an outlet and make sure nothing is in its path.
- Page 14 STEP ELEVEN OPTIONAL ACCESSORY - CROSSBAR Extend the CROSSBAR to match the width of the LEGS by loosening the two middle bolts. These bolts should be facing down. Attach the CROSSBAR to each LEG using 4 M6x25 BOLTS. x4 M6 25 DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS...
- Page 15 INITIALIZING YOUR STANDDESK YOU MUST INITIALIZE YOUR STANDDESK BEFORE USE! Press and hold the down arrow for 15-30 seconds. As you hold the down arrow, the frame will go down to its lowest position and then calibrate. Do not release arrow before calibration is successful.
- Page 16 MEMORY HANDSET MANUAL Setting One Menu Up Arrow LED Display Down Arrow Setting Two Wake: To wake press any button. Setting Three Calibrate PRESS/HOLD 15 seconds LED Display shows RELEASE then Display shows 60. HOLD until Display shows or Reset: GLP: stands for Go to Lowest Position.
- Page 17 MEMORY HANDSET MANUAL (CONTINUED) Setting One Menu Up Arrow LED Display Down Arrow Setting Two Setting Three Set Max PRESS/HOLD 15 seconds RELEASE WHEN LED Display blinks PRESS/HOLD Height: When desk raises to highest point (120 CM) RELEASE PRESS LED Display shows Set Min PRESS/HOLD 15 seconds...