Download
Share
Print this page
  1. Manuals
  2. Brands
  3. StandDesk Manuals
  4. Indoor Furnishing
  5. Dual Motor Stand Desk
  6. Assembly manual

StandDesk Dual Motor Stand Desk Assembly Manual

Hide thumbs Also See for Dual Motor Stand Desk:

Advertisement

Quick Links

Download this manual
DUAL MOTOR
F2 - DM - TS

Advertisement

loading

Related Manuals for StandDesk Dual Motor Stand Desk

Summary of Contents for StandDesk Dual Motor Stand Desk

  • Page 1 DUAL MOTOR F2 - DM - TS...
  • Page 2 Middle Slat Stabilizing Feet Control Box Holder Support Brace Foot Plate Control Box Handset Power Cords Cable Management Tray (optional) Crossbar (optional) Allen Wrench Open Wrench ST3.5x19 ST4.8x19 M6x12 M6x25 M6x30 M6x35 Inserts Washers DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS...

  • Page 3: Caution / Information

    Keep children away from fully electric standing desks, control boxes, and controllers. There is a risk of injury or electric shock. Keep all electrical components away from liquids. Do not sit, stand, crawl or lie on or under the StandDesk Frame. Do not place any objects taller than 20" underneath the StandDesk.
  • Page 4 STEP TWO IMPORTANT! Place the Support Braces on the DESK TOP so they match up with the pre-drilled holes in your top. Attach the SUPPORT BRACES to the outside of each LEG using x4 M6x12 BOLTS. x4 M6x12 MATCH THEM UP DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS...
  • Page 5 STEP THREE If the MIDDLE SLATS arrive disassembled, slide the two MIDDLE SLAT pieces over the U shaped piece. Place your MIDDLE SLATS on your top with the bolt holes facing up. Adjust the length of the SLATS to match the width of the LEGS by loosening the bolts and pulling ends of the SLATS apart.
  • Page 6 STEP SIX Place x1 STABILIZING FOOT PLATE on top of each LEG. Make sure the "lip" of the PLATE is touching the LEG and the smooth side is facing up. MATCH THEM UP DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS...
  • Page 7 STEP SEVEN Place x1 FOOT on top of each STABILIZING FOOT PLATE with Black Pads on the ends of the feet facing Attach each FOOT using x4 M6x12 BOLTS. PRO TIP! Install the bolts in a diagonal pattern to ensure all the holes are aligned before fully tightening.
  • Page 8 STEP EIGHT OPTIONAL UPGRADE - CABLE MANAGEMENT TRAY Remove the x2 PRE-INSTALLED M6x35 BOLTS from the BACK MIDDLE SLAT. Attach the CABLE MANAGEMENT TRAY to the BACK MIDDLE SLAT, making sure the tray is facing the back of your desk using x4 M6x12 BOLTS and x4 WASHERS to attach.

  • Page 9: Control Box

    STEP NINE Secure the CONTROL BOX to the CONTROL BOX HOLDER with x2 INSERTS. Be sure to press the INSERTS down firmly. The screw head should be flush with the rim of the CONTROL BOX. x2 INSERTS DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS...
  • Page 10 STEP TEN Attach the CONTROL BOX HOLDER to the FRONT MIDDLE SLAT using x2 M6x12 BOLTS. The CONTROL BOX HOLDER should be situated in between both MIDDLE SLATS. x2 M6x12 MATCH THEM UP DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS...
  • Page 11 STEP FIVE Use x6 ST4.8x19 SCREWS to attach your SUPPORT BRACES to your TOP. Attach the HANDSET to the front edge of the desk with x2 ST3.5x19 SCREWS. If your desk does not have pre-drilled holes you may have to drill your own.
  • Page 12 STEP ELEVEN Connect the HANDSET CORD, MOTOR CORDS, and POWER CORD to the CONTROL BOX . Go back and ensure all the screws and bolts are fully tightened! Then carefully flip your desk. Plug the desk into an outlet and make sure nothing is in its path.
  • Page 13 STEP TWELVE OPTIONAL ACCESSORY - CROSSBAR Extend the CROSSBAR to match the width of the LEGS by pulling both ends away from eachother. Make sure the bolt holes in the middle of the CROSSBAR are facing the feet. Attach the CROSSBAR to each LEG using 4 M6x25 BOLTS.
  • Page 14 INITIALIZING YOUR STANDDESK YOU MUST INITIALIZE YOUR STANDDESK BEFORE USE! Press and hold the down arrow for 15-30 seconds. As you hold the down arrow, the frame will go down to its lowest position and then calibrate. Do not release arrow before calibration is successful.
  • Page 15 MEMORY HANDSET MANUAL Up Arrow Setting One Menu LED Display Down Arrow Setting Two Setting Three Wake: To wake press any button. stands for HIT. This protects your desk against HIT: You must calibrate your desk collisions that could lead to damage. if something hits your frames while it is raising or lowering, before proceeding with any other step.
  • Page 16 MEMORY HANDSET MANUAL (CONTINUED) Setting One Menu LED Display Up Arrow Down Arrow Setting Two Setting Three 20 seconds 20 seconds PRESS/HOLD PRESS/HOLD LED Display will show PRESS LED Display will show Max/Min twice to show Collision PRESS ADJUST max/min load capacity using Load Sensitivity: then...
  • Page 17 STEP ONE Lay out all of the parts and hardware to ensure you have everything. Assemble your frame on the underside of your desk top. holes for To do this, make sure the top opt. Crossbar is laying on a soft surface such as carpet or towel with the screw holes facing up.
  • Page 18 STEP FOUR Attach the MIDDLE SLATS to the LEGS using x4 M6x35 BOLTS for each MIDDLE SLAT then Back Slat tighten the bolts in the middle of both slats. IMPORTANT! Make sure stickers 5 and 6 are pointing towards the front of your desk. This will help in a later step.