Page 1
SMART UV® UV DISINFECTION STERILIZER INSTALLATION AND USER'S GUIDE IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS...
Page 2
Pentair Aquatic Eco-Systems, Inc. Those names and brands may be the trademarks or registered trademarks of those third parties. Because we are continuously improving our products and services, Pentair reserves the right to change specifications without prior notice.
TABLE OF CONTENTS Important Warning and Safety Instructions ..4 Maintenance ............16 Warranty Information ..........5 Quartz Sleeve Cleaning ........16 System Features and Specifications ...... 6 Winterizing ............16 SMART UV Features .......... 6 Lamp Connector Removal ........ 17 ®...
Warns about hazards that may cause death, of the following situation, DO NOT attempt repairs yourself. Call serious personal injury, or major property Pentair customer service department at 877-347-4788 for services or damage if ignored. discard the appliance. Warns about hazards that may or can cause...
If in doubt consult a qualified electrician. WARRANTY INFORMATION PENTAIR warrants to the original purchaser, the SMART UV The UV lamp has a 90-day warranty on the electrical operation only. Ultraviolet Sterilizers to be free from defects in workmanship or...
SYSTEM FEATURES AND SPECIFICATIONS SMART UV Features All SMART UV Systems UV Sterilizer models are ® packaged complete, with all necessary components Our GPH T-5 and T-6 low pressure mercury vapor that are required to operate the unit. When unpacking, germicidal amps, convert approximately 30% of their it is recommended to perform a complete component electrical input watts into UV-C output watts within...
PRE-INSTALLATION INSPECTION Component Diagram Power Supplies Please review the component diagram below. The power supply can either be a cylinder “POD” Unpack your UV system, and lay out the packaged or a rectangle style. Below are the ballasts that are components for inspection.
PRE-INSTALLATION INSPECTION Quartz Sleeve and UV Lamp Inspection – 2. Carefully, remove the quartz sleeve by unthreading the Black Retaining Nut. Gently slide out the When Packed in Tube quartz sleeve assembly and inspect for damage SMART UV Disinfection Sterilizers are packaged ®...
INSTALLATION 5. With the quartz sleeve positioned inside the Improper assembly may result in water clear quartz sleeve module properly, finish hand- damage to electrical components and unsafe tightening the white retaining nut. When the white conditions. The manufacturer is not responsible for retaining nut is tight, the quartz sleeve should damage cause by improper re-assembly of these appear straight inside the clear quartz sleeve...
INSTALLATION Mounting the Power Supply IMPORTANT NOTE: Failure to perform a leak test could lead to conditions that will void your product Depending on the style of power supply cylinder or warranty. rectangle the SMART UV system’s power supply can ®...
INSTALLATION Electrical Requirements within the GFCI outlet generates a trip signal which is applied to a coil that trips the main (normally closed) The electrical requirements for the UV sterilizer are contacts. These contacts open and break the circuit. marked on the unit’s power supply label (Ex. 120VAC 50/60Hz.).
Page 13
INSTALLATION 2. After a successful leak test and without the power NOTE: By loosening the 3 / 8 inch Threaded Watertight supply connected to a control box, attach the Cord Connector (5), Power Cord adjustments can be lamp’s 4-pins to the power cord’s white 4-pin made.
SMART UV Systems UV Sterilizers are used in a variety of applications to control waterborne This system is simple yet it achieves critical filtering pathogens. Pentair encourages the consideration of goals, such as good water circulation for increased the installation/operation recommendations provided solid waste suspension.
Page 15
OPERATION a check valve or ball valve (see filter instructions/ flow adjustments and UV removal. For best results, recommendations). See Diagram 3. install a saddle-style water flow meter, mounted horizontally on the outlet side of the UV. Follow the water flow meter manufacturer’s instructions for proper installation and operation.
Cleaning frequency is also dependent on how well Pentair recommends shutting the UV system down water is being filtered before reaching the SMART when the temperature consistently falls below 40°F Systems UV Sterilizer. Water that contains solid ®...
MAINTENANCE Lamp Connector Removal 7. Using a “new” 4-pin lamp connector, push the power cord’s tinned wires into the holes of In the event that you would need to replace you the connector making sure that they are firmly 4-pin lamp connector, follow these steps: attached.
TROUBLESHOOTING Paper Towel Leak Test Indicates a Leak 1. Turn off the pool pump at the circuit breaker and be sure all flow to the unit has been stopped. 2. Refer to pages 4–5 for “Quartz Sleeve Assembly” and page 8 for “UV Lamp Installation” (in reverse order) to disassemble the unit.