Setting Clock; Using Default Schedule - Pentair Sta-rite EnviroMAX 1500 Installation, Operation And Service Manual

Setting the Clock
When the pump is first plugged in, the clock will blink to indicate that is has not been set. Any daily
schedule set by the user will be based on this clock setting, so it will be necessary to set the clock first.
To Set the Clock:
1. Press and hold the Display button for 3 seconds.
2. Use the "+" and "-" arrows to choose between a 12 or 24 hour time format.
3. Press Display to advance in the Clock Setup menu
4. Use the "+" and "-" arrows to change the time to the correct time of day. In the 12 hour time format AM/
PM will display in the bottom right corner.
5. Press Display to advance.
6. Use the "+" and "-" arrows to adjust the screen backlight brightness.
7. Press Display to exit the Clock Setup menu. The clock is now set.
During a power outage, the drive will retain the clock setting in memory for as long as 24 hours. If the
power is out longer than 24 hours the clock will have to be set again. If the drive has lost the user set time,
the clock will continuously blink until the time is reset. Once the time is reset the clock will stop blinking.
Note: When power is returned to the pump after a prolonged outage (24+ hours) the clock will
automatically set itself to the Speed 1 start time, blink and advance. The pump will also run the associated
schedule from that start time.
g the Clock
Using the Default Schedule
pump is first plugged in, the clock will blink
e that is has not been set. Any daily schedule
The default schedule is designed to provide enough daily turnover to service a typical pool. See Table 1 for
user will be based on this clock setting, so it
default schedule.
cessary to set the clock first.
Clock:
and hold the Display button for 3 seconds.
he " +" and " -" arrows to choose between a 12
hour time format.
Display to advance in the Clock Setup menu
he " +" and " -" arrows to change the time to
orrect time of day. In the 12 hour time format
M will display in the bottom right corner.
SPEED 1 is set to begin at 8:00am and run at 3000 RPM for a duration of 2 hours. When SPEED 1 is
Display to advance.
complete the pump immediately begins running the default SPEED 2. SPEED 2 is factory default to 1200
RPM and will last for 10 hours. When SPEED 2 has completed its run the pump will run SPEED 3 at 2200
he " +" and " -" arrows to adjust the screen
RPM for a duration of two hours.
ight brightness.
Display to exit the Clock Setup menu. The
After 14 hours of run time and completing its run of SPEED 3, the pump will enter a stationary/paused
is now set.
state for the next 10 hours. The pump will restart at 8:00am the next morning and cycle through the
power outage, the drive will retain the clock
default schedule again. The pump will continue to run in this in this manner until a custom schedule is
memory for as long as 24 hours. If the power
programmed into the drive by the user.
ger than 24 hours the clock will have to be set
he drive has lost the user set time, the clock
Note: The Start/Stop button must be pressed, and the LED lit, for the pump to run.
nuously blink until the time is reset. Once the
set the clock will stop blinking.
hen power is returned to the pump after
ed outage (24+ hours) the clock will
cally set itself to the Speed 1 start time, blink
nce. The pump will also run the associated
from that start time.
11
Operation
OPERATING THE PUMP
Using the Default Schedule
The default schedule is designed to provide enough
daily turnover to service a typical pool. See
for default schedule.
Duration
(Hours)
2
SPEED 1
10
SPEED 2
2
SPEED 3
Table 1: Default Schedule.
SPEED 1 is set to begin at 8:00am and run at 3000
RPM for a duration of 2 hours. When SPEED 1 is
complete the pump immediately begins running the
default SPEED 2. SPEED 2 is factory default to
1400 RPM and will last for 10 hours. When SPEED
2 has completed its run the pump will run SPEED 3
at 2200 RPM for a duration of two hours.
After 14 hours of run time and completing its run of
SPEED 3, the pump will enter a stationary/paused
state for the next 10 hours. The pump will restart
at 8:00am the next morning and cycle through the
default schedule again. The pump will continue to
run in this in this manner until a custom schedule is
programmed into the drive by the user.
Note: The Start/Stop button must be pressed, and
the LED lit, for the pump to run.
7
Table 2
Speed
(RPM)
3000
1200
2200