Table of Contents
Advertisement
Quick Links
Operator's Manual
Infinity-Pak Station
Register your machine:
www.lincolnelectric.com/register
Authorized Service and Distributor Locator:
www.lincolnelectric.com/locator
Save for future reference
Date Purchased
Code: (ex: 10859)
Serial: (ex: U1060512345)
IM10185
| Issue Date Oct- 14
© Lincoln Global, Inc. All Rights Reserved.
For use with machines having K Numbers:
K3926-1, K3927-1, K4106-1
Advertisement
Table of Contents
Related Manuals for Lincoln Electric Infinity-Pak K3926-1
Summary of Contents for Lincoln Electric Infinity-Pak K3926-1
- Page 1 Operator’s Manual Infinity-Pak Station For use with machines having K Numbers: K3926-1, K3927-1, K4106-1 Register your machine: www.lincolnelectric.com/register Authorized Service and Distributor Locator: www.lincolnelectric.com/locator Save for future reference Date Purchased Code: (ex: 10859) Serial: (ex: U1060512345) IM10185 | Issue Date Oct- 14 ©...
- Page 2 THANK YOU FOR SELECTING A QUALITY PRODUCT BY KEEP YOUR HEAD OUT OF THE FUMES. DON’T get too close to the arc. LINCOLN ELEC TRIC. Use corrective lenses if necessary to stay a reasonable distance away from the arc. READ and obey the Safety Data PLEASE EXAMINE CARTON AND EQUIPMENT FOR Sheet (SDS) and the warning label DAMAGE IMMEDIATELY...
-
Page 3: Section A: Warnings
W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is available from the Lincoln Electric Company, 2.d. All welders should use the following procedures in order to 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199. -
Page 4: Electric Shock Can Kill
SAFETY ELECTRIC SHOCK ARC RAYS CAN BURN. CAN KILL. 3.a. The electrode and work (or ground) circuits are 4.a. Use a shield with the proper filter and cover plates to protect your electrically “hot” when the welder is on. Do eyes from sparks and the rays of the arc when welding or not touch these “hot”... - Page 5 SAFETY WELDING AND CUTTING CYLINDER MAY EXPLODE IF SPARKS CAN CAUSE DAMAGED. FIRE OR EXPLOSION. 7.a. Use only compressed gas cylinders containing the correct shielding gas for the process used 6.a. Remove fire hazards from the welding area. If and properly operating regulators designed for this is not possible, cover them to prevent the welding sparks the gas and pressure used.
- Page 6 TABLE OF CONTENTS...
-
Page 7: General Description
INFINITY-PAK STATION GENERAL DESCRIPTION GENERAL DESCRIPTION This guide is designed to assist the user whose primary responsibility ELECTRIC SHOCK CAN KILL is to operate and maintain the Infinity-Pak Wire Dispensing System. This manual provides specific information on installation, safety, basic •... -
Page 8: Installation
INFINITY-PAK STATION INSTALLATION INSTALLATION 1. Parts as shown: A. Base B. Front Leg (adjustable length) 2.0 ASSEMBLY INSTRUCTIONS C. Wire Bridge D. Center Post E. Wire Guide Module Transfer Arm F. Conduit Bridge Some models may feature additional Guide Modules on top of transfer arm. - Page 9 INFINITY-PAK STATION INSTALLATION 2.0 ASSEMBLY INSTRUCTIONS (Continued) 5. Insert the two wire packages into place on the left and right side of the front leg. Adjust the height of the top arm assembly by loosening the two set screws on the base.
-
Page 10: Operation
INFINITY-PAK STATION OPERATION OPERATION SETUP Wire Clamp If using Empty Wire Alert Flag The empty with wire over .052 wire flag installs just above the (1.3mm), disassemble transfer arm on the center post. It and flip the clamping should be set in the downward block around to the position toward the current active textured side for... - Page 11 INFINITY-PAK STATION OPERATION 3.0 BUTT WELDING INSTRUCTIONS 1. Ensure the Wire Size Select switch is in the OFF position. (center). Connect Butt Welder to power supply. 2. Pull down both locking knobs to open wire clamps. 3. Pull and turn the Weld/Open switch to the “Open” position. 4.
- Page 12 INFINITY-PAK STATION ACCESSORIES ACCESSORIES K3921-1 Docking Station Butt Welder K3924-1 Portable Butt Welder GENERAL DESCRIPTION SAFETY PRECAUTIONS: INSTALLATION 2.0 ASSEMBLY INSTRUCTIONS 2.0 ASSEMBLY INSTRUCTIONS (Continued) OPERATION BOX SETUP 3.0 BUTT WELDING INSTRUC- TIONS Burr Removal from Wire Joint using the Wire Sizer ACCESSORIES K3921-1 K3924-1...
- Page 13 Infinity-Pak 2 Station - K3926-1...
- Page 14 General Assembly PART NUMBER DESCRIPTION K3926-1 INFINITY-PAK 2 STATION 9SS30605-1 ROTARY HOUSING ASSEMBLY 9SS30605-2 9SS30605-3 EC-4 CONDUIT & CONNECTOR 9SS30605-4 SWING ARM ASSEMBLY 9SS30605-5 CONDUIT W/ INLET 9SS30605-6 FLAG ASSEMBLY 9SS30605-7 WIRE HOLD DOWN 9SS30605-8 BRIDGE ASSEMBLY 9SS30605-9 BRIDGE RECEIVER ASSEMBLY 9SS30605-10 FRONT LEG W/ SLEEVE 9SS30605-11...
- Page 15 General Assembly P-757-C.jpg Infinity-Pak 2 Station - K3926-1...
- Page 16 Infinity-Pak 4 Station - K3927-1...
- Page 17 General Assembly PART NUMBER DESCRIPTION K3927-1 INFINITY-PAK 4 STATION 9SS30605-1 ROTARY HOUSING ASSEMBLY 9SS30605-2 9SS30605-3 EC-4 CONDUIT & CONNECTOR 9SS30605-4 SWING ARM ASSEMBLY 9SS30605-5 CONDUIT W/ INLET 9SS30605-6 FLAG ASSEMBLY 9SS30605-7 WIRE HOLD DOWN 9SS30605-8 BRIDGE ASSEMBLY 9SS30605-9 BRIDGE RECEIVER ASSEMBLY 9SS30605-10 FRONT LEG W/ SLEEVE 9SS30605-11...
- Page 18 General Assembly P-757-C.jpg Infinity-Pak 4 Station - K3927-1...
- Page 19 Infinity-Pak Wall Mount - K4106-1...
- Page 20 General Assembly PART NUMBER DESCRIPTION K4106-1 INFINITY-PAK WALL MOUNT 9SS30605-1 ROTARY HOUSING ASSEMBLY 9SS30605-2 9SS30605-3 EC-4 CONDUIT & CONNECTOR 9SS30605-15 SWING ARM ASSEMBLY 9SS30605-5 CONDUIT W/ INLET 9SS30605-7 WIRE HOLD DOWN 9SS30605-8 BRIDGE ASSEMBLY 9SS30605-9 BRIDGE RECEIVER ASSEMBLY 9SS30605-16 BASE 9SS30605-17 CENTER TUBE Infinity-Pak Wall Mount - K4106-1...
- Page 21 General Assembly P-757-D.jpg Infinity-Pak Wall Mount - K4106-1...
- Page 22 WARNING Do not touch electrically live parts or Keep flammable materials away. Wear eye, ear and body protection. electrode with skin or wet clothing. Insulate yourself from work and AVISO DE ground. Spanish PRECAuCION No toque las partes o los electrodos Mantenga el material combustible Protéjase los ojos, los oídos y el bajo carga con la piel o ropa moja-...
- Page 23 WARNING Keep your head out of fumes. Turn power off before servicing. Do not operate with panel open or Use ventilation or exhaust to guards off. remove fumes from breathing zone. AVISO DE Spanish PRECAuCION Los humos fuera de la zona de res- Desconectar el cable de ali- No operar con panel abierto o piración.
- Page 24 Lincoln Electric for advice or information about their use of our products. We respond to our customers based on the best information in our possession at that time. Lincoln Electric is not in a position to warrant or guarantee such advice, and assumes no liability, with respect to such information or advice.