Maintenance - Xpelair GX6 Installation And Maintenance Instructions Manual

� The integral timer provides an Remove the back draught shutter/grille
The fan indicator light shows when it the timer overrun (see Fig.H).
adjustable overrun period after the assembly (see "Mounting the fan in the
is switched on. 4. Replace the back draught shutter/
2. Turn the adjuster marked "T" anti-
GX6T
relative humidity level has fallen. hole" section).
� An integral timer provides an grille assembly (see "Mounting the
clockwise to reduce the timer overrun
Turn the adjuster marked "H" anti-
adjustable overrun period after the fan in the hole" section).
� The fan is operated by a remote (see Fig.H).
Switched operation clockwise to decrease the relative
fan is switched off.
switch. 3. Turn the adjuster clockwise to increase
� A manual operation remote switch humidity level of the room (see Fig. 1).
GX6HT
The fan indicator light shows when it the timer overrun (see Fig.H).
starts the fan. The fan indicator light Turn the adjuster clockwise to increase
Adjusting the humidistat setting
is switched on. 4. Replace the back draught shutter/
shows when it is switched on. the relative humidity level of the room
Condensation operation The internal humidity sensor is factory
� An integral timer provides an grille assembly (see "Mounting the
� The integral timer provides an (see Fig.l).
� The fan operates automatically if the set at approximately 70%. The level is
adjustable overrun period after the fan in the hole" section).
adjustable overrun period after the Replace the back draught shutter/grille
relative humidity is above the set adjustable between approximately
fan is switched off.
fan has been switched off. assembly (see "Mounting the fan in the
level. 50% and 90% relative humidity.
hole" section).
� The integral timer provides an GX6HT Remove the back draught shutter/grille
GX6HT2
Adjusting the humidistat setting
adjustable overrun period after the assembly (see "Mounting the fan in the
Condensation operation The internal humidity sensor is factory
Trickle ventilation
Condensation operation
relative humidity level has fallen. hole" section).
� The fan operates automatically if the set at approximately 70%. The level is
� The fan operates automatically at low
Turn the adjuster marked "H" anti-
relative humidity is above the set adjustable between approximately
speed if the relative humidity rises Trickle ventilation is equivalent to that
Switched operation clockwise to decrease the relative
level. 50% and 90% relative humidity.
above the set level. provided by an airbrick or similar device.
� A manual operation remote switch humidity level of the room (see Fig. 1).
� The integral timer provides an Remove the back draught shutter/grille
� The integral timer provides an
starts the fan. The fan indicator light Turn the adjuster clockwise to increase
adjustable overrun period after the assembly (see "Mounting the fan in the
adjustable overrun period after the 1. Remove the back draught shutter/
shows when it is switched on. the relative humidity level of the room
relative humidity level has fallen. hole" section).
fan has been switched off. grille assembly (see "Mounting the
� The integral timer provides an (see Fig.l).
Turn the adjuster marked "H" anti-
fan in the hole" section).
adjustable overrun period after the Replace the back draught shutter/grille
Switched operation clockwise to decrease the relative
Boost operation
fan has been switched off. assembly (see "Mounting the fan in the
� A manual operation remote switch humidity level of the room (see Fig. 1).
� The integral pull cord switches the fan To allow trickle ventilation
hole" section).
GX6HT2
starts the fan. The fan indicator light Turn the adjuster clockwise to increase
on to run at high speed. The fan
shows when it is switched on. the relative humidity level of the room
indicator light shows when high 2. HOLD THE SHUTTER VANES FULLY
Trickle ventilation
Condensation operation
� The integral timer provides an (see Fig.l).
speed has been selected. OPEN.
� The fan operates automatically at low
adjustable overrun period after the Replace the back draught shutter/grille
� A remote switch may be used as an 3. Push down firmly on the trickle vent
speed if the relative humidity rises Trickle ventilation is equivalent to that
fan has been switched off. assembly (see "Mounting the fan in the
alternative to the pull cord. If this is catch until it clicks into position then
above the set level. provided by an airbrick or similar device.
hole" section).
used, cut off the pull cord, after release the shutter vanes. (See
GX6HT2
� The integral timer provides an
ensuring that the pull cord switch is in Fig.F item 6).
adjustable overrun period after the 1. Remove the back draught shutter/
Trickle ventilation
Condensation operation
the "off" position.
fan has been switched off. grille assembly (see "Mounting the
� The fan operates automatically at low
To fully close the shutters and fan in the hole" section).
GXS6
speed if the relative humidity rises Trickle ventilation is equivalent to that
stop any back draught
Boost operation
above the set level. provided by an airbrick or similar device.
� This fan is operated by a remote
� The integral pull cord switches the fan To allow trickle ventilation
� The integral timer provides an
4. Pull the trickle vent catch towards you
switch.
on to run at high speed. The fan
adjustable overrun period after the 1. Remove the back draught shutter/
until it clicks into position.
indicator light shows when high 2. HOLD THE SHUTTER VANES FULLY
GX6 (IP25)
fan has been switched off. grille assembly (see "Mounting the
5. Refit the back draught shutter/grille
speed has been selected. OPEN.
fan in the hole" section).
� This fan is operated by a remote assembly, see "Mounting the fan in
� A remote switch may be used as an 3. Push down firmly on the trickle vent
Boost operation
switch. the hole" section, ensuring that the
alternative to the pull cord. If this is catch until it clicks into position then
� The integral pull cord switches the fan To allow trickle ventilation
actuator lever is in the "fully down"
used, cut off the pull cord, after release the shutter vanes. (See
GX6T / GXC6T / GX6HT and
on to run at high speed. The fan
position.
ensuring that the pull cord switch is in Fig.F item 6).
GX6HT2 only
indicator light shows when high 2. HOLD THE SHUTTER VANES FULLY
the "off" position.
speed has been selected. OPEN.

Maintenance

Before making any adjustments,
To fully close the shutters and
GXS6
� A remote switch may be used as an 3. Push down firmly on the trickle vent
isolate the fan completely from the
stop any back draught
alternative to the pull cord. If this is catch until it clicks into position then
mains electricity supply. A QUALIFIED ELECTRICIAN MUST
� This fan is operated by a remote
used, cut off the pull cord, after release the shutter vanes. (See
CARRY OUT ALL CLEANING.
switch. 4. Pull the trickle vent catch towards you
ensuring that the pull cord switch is in Fig.F item 6).
Adjusting the timer overrun
until it clicks into position.
GX6 (IP25)
the "off" position.
The overrun timer is factory preset at NOTE: THE FAN WILL CONTINUE TO
5. Refit the back draught shutter/grille
To fully close the shutters and
approximately 20 minutes. The time is GXS6 OPERATE WITH THE INNER GRILLE
� This fan is operated by a remote assembly, see "Mounting the fan in
stop any back draught
adjustable between approximately REMOVED HENCE IT MUST BE
switch. the hole" section, ensuring that the
� This fan is operated by a remote
2 to 20 minutes. ISOLATED COMPLETELY FROM THE
actuator lever is in the "fully down"
GX6T / GXC6T / GX6HT and
switch. 4. Pull the trickle vent catch towards you
MAINS BEFORE ANY WORK IS
position.
GX6HT2 only
until it clicks into position.
1. Remove the back draught shutter/ GX6 (IP25) CARRIED OUT.
5. Refit the back draught shutter/grille
Maintenance
grille assembly (see "Mounting the
Before making any adjustments,
� This fan is operated by a remote assembly, see "Mounting the fan in
fan in the hole" section).
isolate the fan completely from the
switch. the hole" section, ensuring that the
mains electricity supply. A QUALIFIED ELECTRICIAN MUST
actuator lever is in the "fully down"
GX6T / GXC6T / GX6HT and CARRY OUT ALL CLEANING.
position.
GX6HT2 only
Adjusting the timer overrun
The overrun timer is factory preset at NOTE: THE FAN WILL CONTINUE TO
Maintenance
Before making any adjustments,
approximately 20 minutes. The time is
OPERATE WITH THE INNER GRILLE
isolate the fan completely from the
adjustable between approximately REMOVED HENCE IT MUST BE
mains electricity supply. A QUALIFIED ELECTRICIAN MUST
2 to 20 minutes. ISOLATED COMPLETELY FROM THE
CARRY OUT ALL CLEANING.
MAINS BEFORE ANY WORK IS
Adjusting the timer overrun
1. Remove the back draught shutter/ CARRIED OUT.
The overrun timer is factory preset at NOTE: THE FAN WILL CONTINUE TO
grille assembly (see "Mounting the
approximately 20 minutes. The time is OPERATE WITH THE INNER GRILLE
fan in the hole" section).
adjustable between approximately REMOVED HENCE IT MUST BE
2 to 20 minutes. ISOLATED COMPLETELY FROM THE
MAINS BEFORE ANY WORK IS
1. Remove the back draught shutter/ CARRIED OUT.
grille assembly (see "Mounting the
fan in the hole" section).
lay face down and pull shutter
and the powered shutter to close.
forwards see Fig.G1 and Fig.G2.
(Cleaning on the GXC6 and GXS6
1. Before cleaning, isolate the fan
can begin once the impeller has
completely from the mains
3. To remove the impeller. Unscrew the
stopped rotating).
electricity supply. Allow 3 minutes
central screw and remove it together
for the impeller to stop rotating
with the washer. Place screw and
2. Remove the back draught shutter/
and the powered shutter to close.
washer to one side.
grille assembly by pressing the
(Cleaning on the GXC6 and GXS6
release catch located on the side of
can begin once the impeller has
4. To clean the impeller, either wipe it
the unit with a 6mm screwdriver or
stopped rotating).
with a damp, lint free cloth or wash it
coin, whilst pulling the grille forward.
in warm soapy water. Thoroughly
To remove the back draught shutter,
2. Remove the back draught shutter/
dry the impeller and refit.
lay face down and pull shutter
grille assembly by pressing the
Replace the screw and washer
forwards see Fig.G1 and Fig.G2.
release catch located on the side of
ensuring that they are securely fitted.
the unit with a 6mm screwdriver or
3. To remove the impeller. Unscrew the
coin, whilst pulling the grille forward.
5. Clean the back draught shutter/grille
central screw and remove it together
To remove the back draught shutter,
assembly and impeller in warm soapy
with the washer. Place screw and
lay face down and pull shutter
water. Do not use strong detergents
washer to one side.
forwards see Fig.G1 and Fig.G2.
or chemical cleaners.
4. To clean the impeller, either wipe it
3. To remove the impeller. Unscrew the
6. Thoroughly dry the back draught
with a damp, lint free cloth or wash it
central screw and remove it together
shutter/grille assembly and refit by
in warm soapy water. Thoroughly
with the washer. Place screw and
sliding the grille back over the realise
dry the impeller and refit.
washer to one side.
catches, the catches will locate in and
Replace the screw and washer
secure the grille (see Fig.G3 and
ensuring that they are securely fitted.
4. To clean the impeller, either wipe it
Fig.G4). For GXS6 MODEL: Ensure
with a damp, lint free cloth or wash it
that the actuator lever is in the "fully
5. Clean the back draught shutter/grille
in warm soapy water. Thoroughly
down" position.
assembly and impeller in warm soapy
dry the impeller and refit.
water. Do not use strong detergents
Replace the screw and washer
7. Do not immerse the fan in water or
or chemical cleaners.
ensuring that they are securely fitted.
other liquids to clean any other
parts of the fan.
6. Thoroughly dry the back draught
5. Clean the back draught shutter/grille
shutter/grille assembly and refit by
assembly and impeller in warm soapy
Never use strong solvents to clean
sliding the grille back over the realise
water. Do not use strong detergents
the fan.
catches, the catches will locate in and
or chemical cleaners.
secure the grille (see Fig.G3 and
Apart from cleaning, no other
Fig.G4). For GXS6 MODEL: Ensure
6. Thoroughly dry the back draught
maintenance is required.
that the actuator lever is in the "fully
shutter/grille assembly and refit by
down" position.
Components Fig. D sliding the grille back over the realise
catches, the catches will locate in and
7. Do not immerse the fan in water or
secure the grille (see Fig.G3 and
1. Back draught shutter.
other liquids to clean any other
Fig.G4). For GXS6 MODEL: Ensure
2. Fan assembly.
parts of the fan.
that the actuator lever is in the "fully
3. Outer grille
down" position.
Never use strong solvents to clean
4. Ladder strips.
the fan.
5. Terminal cover
7. Do not immerse the fan in water or
6. Trickle vent catch
other liquids to clean any other
Apart from cleaning, no other
7. Rear cable entry.
parts of the fan.
maintenance is required.
8. Top cable entry.
9. Rating plate.
Never use strong solvents to clean
Components Fig. D
10. Lugs for screw mounting. the fan.
11. Grille.
1. Back draught shutter.
Apart from cleaning, no other
12. Screw hole caps.
2. Fan assembly.
maintenance is required.
13. Actuator lever (GXS6 model only).
3. Outer grille
4. Ladder strips.
Components Fig. D
5. Terminal cover
6. Trickle vent catch
1. Back draught shutter.
7. Rear cable entry.
2. Fan assembly.
8. Top cable entry.
3. Outer grille
9. Rating plate.
4. Ladder strips.
10. Lugs for screw mounting.
5. Terminal cover
11. Grille.
6. Trickle vent catch
12. Screw hole caps.
7. Rear cable entry.
13. Actuator lever (GXS6 model only).
8. Top cable entry.
9. Rating plate.
10. Lugs for screw mounting.
11. Grille.
12. Screw hole caps.
13. Actuator lever (GXS6 model only).
(
)
,
,
.
,
.