Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for DLab RE100-Pro
Summary of Contents for DLab RE100-Pro
- Page 1 Rotary Evaporator User Manual RE100-Pro LCD Digital Rotary Evaporator Please read the User Manual carefully before use, and follow all operating and safety instructions! Technical specifications and outline are subject to change without prior notice.
-
Page 3: Table Of Contents
LED Digital 7” Square Hotplate Stirrer Contents Preface ................. 1 Service ................. 1 Warranty ................1 Safety Instructions ............2 Proper Use ..............5 Inspection ..............6 3.1 Receiving Inspection ..........6 3.2 Listing of Items ............. 6 Control and Display ............ 6 4.1 Control elements ........... -
Page 5: Preface
Please provide the customer care representative with the Preface following information： Welcome to the “Rotary Evaporator User Manual”. Users • Serial number（on the rear panel） should read this Manual carefully, follow the instructions • Certification and procedures, and be aware of all the cautions when using •... -
Page 6: Safety Instructions
• Ensure that there is sufficient space above the device 1. Safety Instructions as the glass assembly may exceed the height of the • device. Read the operating instructions in full before starting • up and follow the safety instructions. Prior to each use, always check the device, accessories •... - Page 7 • of the distillation equipment. The cooler must work Do not operate the appliance in explosive atmospheres, with hazardous substances or under water. properly. Monitor the coolant flow rate at the cooler • outlet. Only process media that will not react dangerously to •...
- Page 8 relief. mechanism to lift the evaporator piston out of the • heating bath. Evacuate the danger zone and warn those CAUTION! Avoid peroxide formation. Organic peroxides can accumulate in distillation and exhaust in the surrounding area! • residues and explode while decomposing! When the device is switched off or the power supply •...
-
Page 9: Proper Use
supply network if the device power switch is off or the 2. Proper Use plug is pulled out. The instrument is designed for distilling in schools, • The socket for the mains cord must be easily laboratories or factories. Together with the accessories accessible. -
Page 10: Inspection
3. Inspection 4. Control and Display 3.1 Receiving Inspection 4.1 Control elements Unpack the equipment carefully and check for any damages which may have arisen during transport. Please contact Motor manufacturer/supplier for technical support. Condenser Note: Evaporating flask 1. If there is any apparent damage to the system, please do not plug it into the power line. - Page 11 Items Descriptions LED power Push the key and then rotate control knob Speed key to set the rated speed in the range from 20 Lift-up key Lift-down key Speed to 280. Push the key and then rotate control knob Temperature to set the rated temperature in the range LCD display Temp...
-
Page 12: Display
position. LCD display LCD displays the real working state. Display Descriptions Remote Display in case of remote control. Power ON, LED power flash. When the LED power unit running, LED power is lit. Display when the rotating function is switched ON. Power switch Power ON or OFF. -
Page 13: Installation And Operation
symbol switched ON. CAUTION! Loosen transportation lock (Figure 7). When setting timer, displaying the rated Timer display • Hold the lift with your hand on the height position and time. When the timer function is area remove the thumb screw on the back of the appliance switched ON, displaying remaining time. - Page 14 • The plastic screw nut (f) helps loosen tight-fitting • piston ground-in connections (Figure 9). Remove the clamping device for the angle setting of the rotation drive on the right side of the lift by Hold the tight-fitting evaporator piston and rotating the knurled screw (d) counter clockwise.
- Page 15 device at 200 rpm for 2 min. Then tighten the cap nut firmly. Figure 10 Figure 12 Figure 11 • Figure 13 Installing condenser (g) (Figure 12 and Figure 13). • Load the cap nut (h) and locking spring (i) to Installing the vertical glassware condenser locking condenser in turn.
-
Page 16: Operation
• Connecting tubes (Figure 15). Vacuum tube Cooling water Cooling water Figure 14 Figure 15 5.2 Operation • Make sure the required operating voltage and power supply voltage match. • Ensure the socket must be properly grounded. • Plug in the power cable，ensure the power is on and begin initializing. -
Page 17: Faults
Release Lift-up/Lift-down key, the lift stops. 6. Faults • Push the speed key and then rotate control knob to set • Instruments can’t be power ON the rated speed. - Check whether the power line is unplugged • Push the temperature key and then rotate control knob - Check whether the fuse is broken or loose to set the rated temperature. -
Page 18: Maintenance And Cleaning
7. Maintenance and Cleaning Note: • Electronic device can not clean with • Proper maintenance can keep instruments working cleanser. properly and lengthen its lifetime. • If you require maintenance service, must be • Do not spray cleanser into the instrument when cleaned the instrument in advance to avoid cleaning. -
Page 19: Associated Standards And Regulations
interference when the equipment is operated in a 8. Associated Standards commercial environment. This equipment generates, uses, Regulations and can radiate radio frequency energy and, if not installed Construction in accordance with the following safety and used in accordance with the instruction manual, may standards: cause harmful interference to radio communications. -
Page 20: Specifications
Permissible Ambient 9. Specifications 5 - 40 Temperature [° C] Items Specifications Permissible Relative Humidity Voltage [VAC] 100-240 Protection Class acc. To DIN IP20 Frequency [Hz] 50/60 EN60529 Power [W] 1400 External rotor brushless Table 4 Motor motor Speed Range [rpm] 20-280 Speed Display Reversible... - Page 22 DLAB Scientific Instrument Inc. 2311 E. Locust Court, Ontario, CA 91761 United States. Office: +1-747-230-5179 Fax: +1-909-230-5275 Sales contact: info@dlabsci.com Service contact: service@dlabsci.com www.dlabsci.com...
Need help?
Do you have a question about the RE100-Pro and is the answer not in the manual?
Questions and answers